Answered: 1-7. The pre-cast T-beam has the…

1-7. The pre-cast T-beam has the cross-section shown. Determine its weight per foot of length if it is made from reinforced stone concrete and eight-in. cold-formed steel reinforcing rods.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4-10 Compute M, and check As.min for the beam shown in Fig. P4-10. Use f'. = 5000 psi and fy =…

Q: Draw the shear, moment and axial load diagrams for each 25 kN 20 kN -1.5 m- 2 m- +1.5 m- B of the…

A: Diagrams showing how shear force changes along the length of a beam are called shear force diagrams.…

Q: The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab.…

A: From given figure ; Required member = BF - Dead load = Density of slab X Thickness Density of slab =…

Q: B 400 N 200 N E) FBD of pipe AB above. Fixed support at B. Thrust-bearing at A.

Q: The column consists of a wooden post and a concrete Tooting, separated by teel bearing plate. Find…

Q: the beam has a roof with a slope of 40mm/m. it is located in an open field where the ground snow…

A: Given data: Ground snow load (Pg) = 1.5KN/m2 Slope of roof ( θ…

Q: Q/ Draw A.F.D, S.F.D and B.M.D. for the beam shown below 6 kN/m B 3 M

A: The following figure shows the Free Body Diagram of the beam.

Q: An 8.0x8.0m interior bay in a continuous floor of an offshore platform has to be designed under the…

Q: Determine the moment capacity, øMa, for a 14 in. x 32 in. reinforced concrete beam with 7 - #6…

Q: support the 6-il ightweight plal Ming a thick portio and therelore its Dotton coated with 5psf…

A: For the concrete slab :Loading =ρconc×w×t=3pdf2×6ft=192 lb per feetFor the plaster ceiling :Loading…

Q: The wall is 12-ft high and consists of 2 × 4 studs. On Answer : 1008 ib/ft each side is acoustical…

A: Given that height of the wall(H) = 12'For the 2 x 4 in studs:The minimum dead load for 2 x 4 in…

Q: Using three moment equation method, draw the bending moment diagram of the structure. 6t 18t 4t\m I…

Q: Q1/ Jet water in pipe with diameter equal to 50mm moving to velocity 30 m/sec. divided in two…

A: Given data Diameter Velocity Discharge ratio To find Forces

Q: Perform a cantilever method to determine the force and moment of the three-storey frame given below.…

Q: A C 3m L-6m en El = 10,000 kN-m² he given beam, you can choose Double Integration Method or I Method…

Q: 12-47. The wooden beam is subjected to the load shown. Determine the equation of the elastic curve.…

A: We will use superimposition method.

Q: |2KN P K 32KN Com E A 10m Nem Kum 1om

Q: 16" For the short of cross sectio shown, P and en at the balanced condition using bas principles.…

Q: 2- Calculate the Design moment strength for the shown floor system. Span is 34 ft and: f=40,000 psi…

A: The given data is: Span length=34 ft fy=40,000 Psi fc'=4000 Psi bw=12 " hf=3"

Q: 2-3. The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab.…

Q: The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab.…

A: Procedure: Find the slab behaviour and find the type of slab Draw tributary area of the joist and…

Q: 5. Design a rectangular reinforced concrete beam subjected to a factored load moment, Mu=250 ft-kip…

A: Given- Mu=250ft-kipb=10inh=24fc=4000 Psify=60,000psistirrups=3

Q: Determine the depth of compression block. of a beam with 375 mm width, 675 mm depth and reinforced…

Q: Design a square column to carry the working load of 1200 kN

A: given- a square column carrying load of 1200KN grade of steel=500 grade of concrete=M20

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Given: The working stress for wood is 1000 psi. The working stress for concrete is 450 psi. Consider…

Q: Determine the T1 and T2 on the rope if the resultant is 5 kN as shown. 5 kN / 50 deg

Q: Q/ Draw A.F.D, S.F.D and B.M.D. for the beam shown below 6 KN/m B 3 M

Q: The column consists of a wooden post and a concrete footing, separated by a steel bearing plate.…

A: Diameter of wooden post=8in side for the concrete footing=12in Working stress for wood=1100psi…

Q: For the overhanging beam, determine (a) the value of Ely under the 24 kN load; and (b) the maximum…

Q: 1-2. The floor of the office building is made of 4-in.-thick lightweight concrete. If the office…

A: Given Data:Floor thickness=4inLength of floor = 20ftwidth = 15ft

Q: 3. Determine if the beam shown will fail in tension or compression. Use fy = 60,000 psi and f'c =…

A: Given - As =6.00 in2 f'c = 4000psi = 4ksi fy = 60000 psi = 60ksi

Q: 1) Show shear force diagram and bending moment diagram for the loading shown below 15 kips 8 kips w…

Q: the lightest available section a service live load of 3.B =

A: solution step 1 . load combination and moment calculation L =34 ftsupported dead load =1.6…

Q: The building wall consists of 12-in. clay brick. In the interior, the wall is made from 2 x 4 wood…

Q: Reinforced Depth Singly 5.75mm. and a Beam width of 250mm. if the Beam is reinforced with…

Q: The beam is built up of 1/4-in vertical plywood strips separated by wood blocks. Determine the…

Q: %06 O Take Quiz Exit Assume the area of the interior columns is twice the area of the exterior…

Q: 2-57. If the resultant force acting on the bracket is required to be minimum, determine the…

A: Given ; To Find : The magnitude F1 and resultant force FR

Q: The horse stall has a flat roof with a slope of 80 mm/m. It is located in an open field where the…

A: Solution: Given, slope of Roof=80 mm/m =80mm1000mm=0.08 Slope, tanθ=0.08θ=tan-10.08=4.57°<5° Snow…

Q: 1-1. The floor of a heavy storage warehouse building is made of 6-in.-thick stone concrete. If the…

A: Given:- thickness = 6 in Length = 15 ft width = 10 ft To find:- Resultant force caused by dead load…

Q: The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab.…

A: Given Data:Floor system 4in reinforced stone conc.slaba=8ftb=8ft

Q: The floor system used in a school classroom consists of a 101.6 mm reinforced stone concrete slab.…

A: Draw the tributary area in the slab.

Q: Situation 1. A 7.5 m long simply supported beam has a cross sectional area of b = 400 mm by h = 550…

A: Answer We are given Beam span L = 7.5 m width b = 400 mm height h = 550 mm Tension reinforcement…

Q: A cantilever is to be constructed from a 40 mm x 60 mm T-section beam with a uniform thickness of 5…

A: The length of the cantilever beam (L)=1 m, The cross-section dimensions=40 mm×60 mm, Stress(σy)=225…

Q: The given plan below shows a 2-way floor system carried by 1-story 2-bays frame system as shown in…

A: Solution Note= you asked multiple questions. I only solve I Part for You

Q: If the coefficient of static friction at the contact points A and B is 0.40, determine the minimum…

Q: 7-21. If the beam is made from wood having an allowable shear stress Tallow = 400 psi, determine the…

Q: Design a square base plate to support 12 mm thick pipe column with an inside diameter of 400 mm. The…

Q: 3. The steel framework is used to support the reinforced stone concrete slab that is used for an…

A: Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: calculate the depth of neutral axis of a beam of size 450 x 300mm. Use M25 concrete grade and 4 no.s…

A: Consider the free body diagram As per limit state method. IS-456:2000 The diameter of…

Concept explainers

Sizing Joists and Rafters

In civil engineering and building construction, joists and rafters are the major components including beams and columns. Almost every structural construction including buildings, skyscrapers, bridges, commercial complexes, and so on makes use of joists and rafters to provide structural integrity to the building. Joists are primarily thick long pieces of metals, concrete, or wood that are used to support the floor and ceiling. On the other hand, rafters form the major component of pitched roofs, which are a series of sloped long pieces extending from a ridged area that makes contact with the plane area of the wall. They account for the load-bearing of the building along with the beams.

Question

1-7. The pre-cast T-beam has the cross-section shown.
Determine its weight per foot of length if it is made from
reinforced stone concrete and eight -in. cold-formed steel
reinforcing rods.
8 in.
8 in.
20 in.
F15 in.
-15 in..
6 in. 6 in. 6 in.
00

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Calculate the required steel area for a reinforced concrete T-beam with an effective flange width of 1200 mm and a slab thickness of 100 mm. The beam is to carry an ultimate moment of 1300 kN-m. The width of the web is 300 mm and the effective depth is 550 mm. Assume f’c = 28 MPa and fy = 400 MPa * a. 7772 mm² b. 8256 mm² c. 7932 mm² d. 7232 mm²
A floor system consisting of 100mm thick concrete slab cast monolithic with continuous T beams of 8m span and on a center-to-center spacing of 1.20m. Web dimensions are bw = 300mm and d = 500mm. The midspan is reinforced with 6-32mm bottom bars and 2-32mm top bars. f'c = 21MPa, fy = 415Mpa. Determine the ultimate bending moment at midspan.
calculate the depth of neutral axis of a beam of size 450 x 300mm. Use M25 concrete grade and 4 no.s of Fe500 steel at the bottom with a cover of 25mm
SITUATION A: The floor system shown has the following applied loads. Super Imposed Dead Load = 2.00 kPa Live Load = 1.90 kPa Slab Thickness = 100.00 mm Weight of Concrete = 24 kN/m3 Self-Weight of the beam = 1.92 kN/m Material Specifications: f’c = 21.00 MPa fy = 345.00 MPa Steel Cover = 50.00 mm What is the maximum positive moment of beam BE, acting on the midspan? in kN-m What is the maximum steel ratio of the section located at the supports? What is the actual steel ratio of the beam section at the supports? What is the ultimate moment capacity of the beam at the supports? in kN-m What is the effective flange width at the midspan? in mm What is the height of the compression block of the section at midspan? in mm What is the ultimate moment capacity of the beam at the midspan? in kN-m What would be the height of the CHB that can be placed on beam BE? Assuming the weight of the blocks is 2.30 kN/m per meter height? in meters
The pre-cast T-beam has the cross-section shown. Determine its weight per foot of length if it is made from reinforced stone concrete and eight 3/4 -in. cold-formed steel reinforcing rods.
The 5 Story Apartment building has the following design specifications. The 5m normal-weight concrete cantilever beam is subjected to a factored Mu = 452 kN-m and a factored shear Vu = 222 kN at the face of the support. Design the top reinforcement and the appropriate embedment of 90° hook into the concrete wall to sustain the external shear and moment. Use f’c =34 MPa, fy = 420 MPa. Beam dimensions: h = 600mm, d = 525mm, b = 375mm.
The floor system used in a school classroom consists of a 4-in. reinforced stone concrete slab. Sketch the loading that acts along the joist BF and side girder ABCDE. Set a = 7.5 ft, b = 20 ft. Hint: See Tables 1.2 and 1.4.
The figure shows a beam column joint. In a continuous building frame analysis, the maximum negative moment at the face of thesupport is 268.04 kN-m, requiring a steel reinforcement area of 1871 sq.mm. 2D36mm bars are provided. Normal density concrete is to be usedwith fc’=27.6 MPa and fy=414.7MPa
The overhanging beam shown supports the given ultimate load Wu= 5okN/m. The section is 300mm by 500mm rectangular beam having f'c=35MPa, fy=420 MPa, stirrups diameter = 10mm and concrete cover 40mm. a.) Calculate the vertical reaction at B in kN b.) Calcute the vertical reaction D in kN c.) Calculate the area of steel reinforcement corresponding to rho max in mm^2. d.) Calculate the location of the point of zero shear in the beam measured from the left support B in mm. e.) Calculate the maximum positive moment in the beam in kN.m.s
A pre-tensioned beam 160 mm wide and 320 mm deep is prestressed by four plain wires of 7 diameter at an eccentricity of 100 mm. If the cube strength of concrete at transfer is 40 N/mm2. Estimate the transmission length at the ends of the pretensioned member using IS: 1343 code provisions.
Explain briefly the purpose of the bearing plate between the steel column and the concrete pedestal.
A continuous beam is shown. Determine momen't A, B, C, and D.