1-95. If the allowable tensile stress for the bar is (ot) allow 12 ksi, determine the the allowable shear stress for the pin is Tallow = diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take tin. and w = 2 in. = 21 ksi, and

1-95. If the allowable tensile stress for the bar is (ot) allow 12 ksi, determine the the allowable shear stress for the pin is Tallow = diameter of the pin so that the load P will be a maximum. What is this load? Assume the hole in the bar has the same diameter d as the pin. Take tin. and w = 2 in. = 21 ksi, and

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for the steel is (sfail)st = 350 MPa, determine the minimum thickness t of the pipe if it supports the force of 500 kN. Use a factor of safety against failure of 1.5. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.5. The failure bearing stress for concrete is (sfail)con = 25 MPa.
Design the beam using the Working stress diagram to resist the loads. Take fc = 10 MPa, fs = 120 MPa, n = 12, bar diameter = 20 mm. Take b = d/2.
The 1.25-in diameter steel shaft BC is built into the rigid wall at C and supported by a smooth bearing at B. The lever AB is welded to the end of the shaft. Determine the force P that will produce a 2-in. vertical displacement of end A of the lever. What is the corresponding maximum shear stress in the shaft? Use G = 12 x 106 psi for steel, and neglect deformation of the lever. Please write legibly, thank you
The timber member BC, inclined at angle 0 = 60° to the vertical, is supported by a pin at B and the 0.75-in.-diameter steel bar AC. (a) Determine the cross-sectional area of BC for which the displacement of C will be vertical when the 5000-1b force is applied. (b) Compute the corresponding displacement of C. The moduli of elasticity are 1.8 x 106 psi for timber and 29 x 106 psi for steel. Neglect the weight of BC.
STRENGTH OF MATERIALS The steel pipe is supported on the circular base plate and concrete pedestal. If the normal failure stress for steel is 360MPa, determine the minimum thickness t of the pipe if it supports the force of 600KN. Use a factor of safety against failure of 1.50. Also, find the minimum radius r of the base plate so that the minimum factor of safety against failure of the concrete due to bearing is 2.50. The failure bearing stress for concrete is 28MPa.
The rigid bar ABCD of negligible weight is initially horizontal, and the steel rods attached at A and C are stress-free. Ifa20-kip load is applied, determine the vertical displacement in the barat ?and C that will cause a stress in the rod at C to be 50ksi. Indicate the direction of movement. Use E=29x106psi for steel.(Provide FBD and movement diagramin your computation).
ABCD is a rigid rod. Cross section area of AE=BF=400 mm2 Find the normal stresses of the bars ae and BF. Calculate the displacement of point D E=200Gpa
The uniform 3000kg bar is supported by a smooth wall at A and by a pin at B. Determine (a)the diameter of the smallest pin that can be used if not to exceed a shear stress of 60MPa(Drawthe required FBD and answer in mm)(b) the bearing stress in thesupport bracket (Draw the required FBD and answer in MPa)(c) the bearing stress in the bar at B (Draw the required FBD and answer in MPa).
If P=13000 N, d=22mm and t=33mm, determine the bearing stress between the rivets and plate, in MPa?
The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? Calculate also the allowable force in rod 1. Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
The simply supported wood beam carries a uniformly distributed load of w = 700 lb/ft, where LAB= 8.0 ft and LBC = 16.0 ft. The beam cross-sectional dimensions are b = 6.2 in., d = 20.4 in., yH = 5.6 in., and yK = 8.0 in. Section a–a is located at x = 4.0 ft from A.(a) At section a–a, determine the magnitude of the shear stress in the beam at point H.(b) At section a–a, determine the magnitude of the shear stress in the beam at point K.(c) If the allowable shear stress for the wood is 140 psi, what is the largest distributed load w that can be supported by the beam? Draw a horizontal line through point H. Use the area above this line to calculate the first moment of area associated with point H.Answer:QH = in.3
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.65x105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?