1) A filter is used to remove the highest frequency component of the signal with the spectrum shown above. What is the minimum required sampling frequency for this new signal? 2) What if only the lowest spectrum component of this signal was required. What would be the cuttoff frequency specification of this pre-conditioning filter. What type of filter would you use for this? (edited) 700 600 500 400 300 200 100 10 20 30 40 50 60 70 80 90 100 Frequency

1) A filter is used to remove the highest frequency component of the signal with the spectrum shown above. What is the minimum required sampling frequency for this new signal? 2) What if only the lowest spectrum component of this signal was required. What would be the cuttoff frequency specification of this pre-conditioning filter. What type of filter would you use for this? (edited) 700 600 500 400 300 200 100 10 20 30 40 50 60 70 80 90 100 Frequency

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Sketch the Vout/Vin versus frequency characteristics of an LC Bandpass filter. Show flc and fhc on the sketch and explain how they are defined. On this sketch, show the bandwidth (BW) of the filter and explain how it is defined.
Let R = 150 Ohm and C = 1uF. What is the peak gain offered by this filter? At what frequency does the frequency response achieve this gain? What is the lower cutoff frequency? What is the upper cutoff frequency? What is the passband width?
Consider the following continous time signal x(t). Assume that the signal was sampled at a sampling frequency of 20 Hz. Plot the magnitude spectrum of the sampled signal as a function of cyclic frequency. Be sure to include n values of up to +-2. Label x and y axis. Did aliasing occur? If so, what is the aliased frequency? x(t) = 1 + 2cos(2pi25t)
Given an analog signal. m(t) =5cos .2000t)+2cos(2π .4000t), for t>0, sampled at a rate of 7,000 Hz, a. sketch the spectrum of the original signal; b. Sketch the spectrum of the sampled signal up to 20 kHz; c. sketch the recovered analog signal spectrum if an ideal low pass filter with a cutoff frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal.
1. Given an analog signal x(t)=10 cos(2π.5500t)+5 cos(2π.7500t) is sampled at a rate of 8,000 Hz, a. Sketch the spectrum of the sampled signal up to 20 kHz; b. Sketch the recovered analog signal spectrum if an ideal low pass filter with a cutoff Frequency of 4 kHz is used to filter the sampled signal in order to recover the original signal; c. determine the frequency/frequencies of aliasing noise.
Determine the gain and cutoff frequencies of the active filter circuit below and draw the response graph.
(can you solve it fast?) What filter type is the digital system given transfer function?
Design a high pass filter with a cut of frequency of K1 and a passband gain of K2. Take K1 equal to 27 in kHz and K2 is the 7 (b) Plot the Bode plot of the frequency response of the designed circuit using a python script and validate your answer. (c) How would you increase the passband gain by a factor of five without changing the cutoff frequency?
help please with explain A narrowband FM signal has a carrier frequency of 110 kHz and a deviation ratio of 0.05. The modulation bandwidth (signal bandwidth) is 10 kHz. This signal is used to generate a wideband FM signal with a deviation ratio of 18 and a carrier frequency of 98 MHz. a) Give the required value of frequency multiplication, n. b) Give two frequencies for the mixer to give the desired carrier. c) Define the required bandpass filter (center frequency and bandwidth).
1- Explain the principle of direct method generation of FM signal.2- What is the difference between narrowband FM and wideband FM refer tothe spectral component of the two signals.3- Compare the S/N ratio of:a) AM DSB-LCb) AM SSB-SCc) FM4- Explain the operation of frequency demodulation by using the PLL method.5- Explain what Carson's rule is.
Q 2 :J An audio signal given by 15sin(4000pi * t) + 20sin(8000pi * t) amplitude modulated(DSB-FC) a sinusoidal carrier wave 60sin(100, 000pi * t) a. Derive an expression for the modulated signal. b. Find the modulation index. c. Find the spectrum of the modulated signal. d. Sketch the spectrum of the modulated signal e. Which type of demodulation method you propose to reconstruct the audio at receiver. Why? to
a control system incorporates a sensor in its system with the signal frequency shown in the fist image i have attatched. This signal is then filtered to give the new output shown in the second image i have attatched. What type of filter has been used here? Can you provide a hand drawn sketch of an idealised represenation of its frequency response?