1 A one room service building is shown in Fig (1), All walls are bricks walls with thickness 036 I -0.36 m Example 130 Xor &8 Slab thickness=t = given in table, If it is reinforced with at top and bottom and in both directions as in table below. a- Find the maximum live load that can be 036 applied safely. Note : Do not check the shear. 0.36 036 Fig (1) GROUP B Reinforcement L1, L2, t, We spacing kN/m m mm 21 350 #13@175 15 3.75 110

1 A one room service building is shown in Fig (1), All walls are bricks walls with thickness 036 I -0.36 m Example 130 Xor &8 Slab thickness=t = given in table, If it is reinforced with at top and bottom and in both directions as in table below. a- Find the maximum live load that can be 036 applied safely. Note : Do not check the shear. 0.36 036 Fig (1) GROUP B Reinforcement L1, L2, t, We spacing kN/m m mm 21 350 #13@175 15 3.75 110

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The standard load is 100kN. Given that n=4 and α=1, calculate EALF 80.
Pls solve with FBD’s it’s imperative. Handwritten answers only. The building section associated with the floor plan in Figure P2.3 is shown in Figure P2.7. Assume a live load of 60 lb/ft on all three floors. Calculate the axial forces produced by the live load in column C2 in the third and first stories. Consider any live load reduction if permitted by the ASCE standard.
Describe about the cyclic loading method.
Will rate immediately. need asap answer. Ty A reinforced concrete column carries a dead axial load of 500 kN, a live axial load of 650 kN and a compressive earthquake load of 270kN. Use fc'=27.6MPa and fy=350Mpa 1. If the size of the column is limited to 250mmx400mm, what must be the number of 20mm diameter bars? 2. If the sise of the column is limited to 300mm diameter, what must be the number of 20mm diameter bars? 3. Determine the ultimate axial load that the column will carry 4. Determine the smallest dimension of the spiral circular column section if the steel ratio 1.25%
Please Answer it fast on Sheet of paper. F1=1.5KN ,F2=3.8KN, a=3.6m ,b=2.0m ,c=1.3m. You need to find Forces in member (CH,AH and CD) And whether it's +ve or -ve.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2.0 mon centers, on simple supports over a span of 6.0 m. The floor supports a superimposed servicedead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa,calculate: 7. Factored uniform load on a typical interior beam in KN/m using load factors of 1.2 for dead load and 1.6 forlive load.
If the resultant force acting on the bracket isrequired to be a minimum, determine the magnitudes of F1and the resultant force. Set Φ = 30°.
Question 45 Calculate the nominal shear strength (kN) of 4-legged stirrups 10-mm-diameter, spaced at 210 mm on centers for a beam with effective depth of 470 mm. Use yield strength of stirrups fy = 275 MPa.
1. The aluminum block has a rectangular cross section and is subjected to an axial compressive force of 8 kip. If the 1.5-in. side changed its length to 1.500132 in., determine Poisson’s ratio and the new length of the 2-in. side. Eal = 10(103 ) ksi.
The appied load on a shallow square fondation makes an angle of 20° wiht the vertical. Given: B= 5 ft, Df= 3 ft, γ= 115 lb/ft3, φ’= 25°, and c’= 600 lb/ft2. Use FS= 3 and determine the gross inclined allowable load. Use Eq (6.28)
A five-storey building is subjected to a windload, computed Vu = 2,350 KN, design the reinforcement of a shear wall that is 5.8m long and 4.2m high, and 250mm thick. F’c= 23.5MPa and fy=275MPa. If the wall is considered to be a load bearing with a concentrated load, Pu= 7,255 KN, can the thickness of wall carry the ultimate axial load, otherwise what is the design wall thickness? Assume . Sketch the rebar details.
HELP ME PLEASE URGENT!! 3 DECIMAL POINT 1. Determine the design compressive strength of the beam column in KN.02. Determine Cb.0 3. Determine the nominal moment strength of the beam column in KN.m.04. Compute the AISC moment amplification factor.0 5. Determine the required factored load in KN.06. Determine the maximum axial service load P (KN) that can be applied.0