1- Consider the unit cube shown in the Figure, which undergoes the deformation: x₁ = a (x₁ - - X₂), x₂ =BX2,, x3 = Y X3 where a, ß, and y are constants. Determine: (a) the deformed length of diagonal OA, a В (b) the condition that constants a, ß, and y must satisfy if the material is incompressible. 1.0 0.8 1.2

1- Consider the unit cube shown in the Figure, which undergoes the deformation: x₁ = a (x₁ - - X₂), x₂ =BX2,, x3 = Y X3 where a, ß, and y are constants. Determine: (a) the deformed length of diagonal OA, a В (b) the condition that constants a, ß, and y must satisfy if the material is incompressible. 1.0 0.8 1.2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The bars shown below, with solid circular cross-sections, are made of a material with an elastic modulus E = 20,000 ksi and a coefficient of thermal expansion α=(15×10^(−6)) 1/°F Bars AB and BC are subjected to a temperature change in addition to the applied forces. If the reaction at C is 8 kips in compression, determine the temperature change ∆T
The lower ends of the three bars in the figure are the same level before the rigid homogeneous W=100 kN block is attached. The properties of the bars are shown in the table. The temperature of the bars is then increased by 80°C. The block is assumed to remain horizontal after all deformations have occured. a.) Which of the following most nearly gives the temperature rise to cause all of the applied loads to be supported by the steel rods? b.) Which of the following most nearly gives the stress developed in the bronze bar? c.) Which of the following most nearly gives the stress developed in the steel bar?
The strain components Ex, Ey, and Vxy are given for a point in a body subjected to plane strain. Determine the strain components En, Et, and Ynt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle O. Sketch the deformed shape of the element. Ex = -850 UE, Ey = 310 UE, Vxy = 1050 urad, and 0 = 39°.
#1 Determine the deformation of point b in mm
An aluminum pipe (modulus of elasticity 10.1x10^6 psi) is fixed at one end and is subjected to a tensile load of 127.5 kips at the free end. The length and cross-sectional area of the pipe is given as 36.1 in and 9.11 in^2. Assume that the aluminum pipe has clockwise torques (100 lb-in) acting at the midpoint and free end of the pipe. (a) Derive the element stiffness matrix
A state of stress is specified in the figure shown below. Determine the Normal stress σy (mPa) on the Principal Plane if P1 = -5 mPa; P2 = 39 mPa and v = 21 mPa
A horizontal bar of negligible mass, hinged at A in FIGURE Z and assume rigid, is supported by a bronze rod 2 m long and a steel rod 1 m long. For the steel rod, the area is 600 mm², and E = 200 GPa. For the bronze rod, the area is 300 mm², and E = 83 GPa. Which of the following most nearly gives the elastic deformation in the bronze rod? a. 0.58 mm b. 1.36 mm c. 2.56 mm d. 3.18 mm
A cantilever beam AB with a circular cross section and length L =750 mm supports a load P =800 N acting at the free end (see figure). The beam is made of steel with an allowable bending stress of 120 MPa. a. Determine the required diameter dmm(figure part a) of the beam, considering the effect of the beam's own weight. Repeat part (a) if the beam is hollow with wall thickness t =df$ (figure part b); compare the cross-sectional areas of the two
The bar ABC shown below is loaded by a force P acting at the end C and by a force Q acting at the midpoint B. The bar has constant axial rigidity EA (20pts) 0) 0) Determine the strain energy Ul of the bar when the force Pacts alone (Q Determine the strain energy U2 of the bar when the force Q acts alone (P Determine the strain energy Us of the bar when the forces P and Q act simultaneously upon the bar. b. c. Use the following values to solve the problem: P=30kPa Q=75 kPa E = 130 GPa L=10 m Bar's cross section 450mm 450mm
Three bars each made of same material are connected together and placedbetween two walls when temperature is T1 = 12°C. (a) Determine the temperature in which the first element yield (Tyield) (b) Increase further temperature from the obtained Tyield by further 50°C degrees, then determine the distance of Point B from two walls and the thermal stress generated in each bars. The material properties and cross-sectional area of each bar are given in the figure
The figure shows the state of stress onthe element at a point on a member. Determine thestress components acting on plane AB
A closed right circular cylinder has radius 4 units and height 18 units A load of an unknown weight is put on top of the cylinder, causing the cylinder to shorten by 2.1 units. Find the new volume of cylinder due to this deformation in the height of the cylinder.