1) Describe the operational features of digital power relay and circuit breaker designed to protect a 100 A radial power feeder, include in your description forms of protection provided by the relay and methods of obtaining line data. 2) Discuss why power system load flow analysis is undertaken and why iterative methods are used.

1) Describe the operational features of digital power relay and circuit breaker designed to protect a 100 A radial power feeder, include in your description forms of protection provided by the relay and methods of obtaining line data. 2) Discuss why power system load flow analysis is undertaken and why iterative methods are used.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter10: System Protection

Section: Chapter Questions

Problem 10.27P

See similar textbooks

Similar questions

A wind farm is being built on an island 6km offshore and needs to be connected to the power grid substation 12km down shore before it can become operational. The cost of laying cable under water is $10,000/km, and the cost of laying cable on land is $8,000/km. a) Determine the cable route that will minimize cost. b) What is the minimum cost
Apply lasso analysis to find i Commentary: PLEASE, describe the procedure step by step, in detail. Do not do it on paper, digitally here :)
1) Time-current relay of IDMTL characteristic is generally used to achieve good discrimination in protection of:? (a) Transmission lines (b) Circuit breakers (c) Generators (d) Large motors 2- The time delay coordination (CDT) for overcurrent protection relays. d) None of these. (a) 0.1s (b) 0.2s (c) 0.4s (d) 0.5s 3-power line carrier (PLC) protection scheme is used to protect?A-power transformer, B-large motor c-long transmission lined- short transmission line
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
ASSIGNMENT 1 #1 Explain the concept of reliability and function of reliability engineering. Give three (3) reasons for studying reliability State three (3) major steps to take to accomplish reliability engineering What is product life cycle? State the stages involved in product life product. Why is it important to integrate reliability engineering into product life cycle? Describe the key engineering tasks and reliability roles in each phase of a product life cycle. Explain the important difference between serial and concurrent product realization processes. How should a reliability program be organized in the environment of concurrent engineering?
2 Give three (3) reasons for studying reliability
13.Transient stability of the power system can be improved by using? O single Lines O Parallel Lines O Alloy conductors O Single Bundled Lines
Describe the key components of a power transmission system and their functions.
Note: Answer the question by Poles and Zeros of the System "Function H(z)" & Comments on System Causality and Stability. Also, please explain the answer with the drawing.
Suppose a power system consists of two isolated regions: a western region and an eastern region. Five units have been committed to supply 3090 MW as shown below. The two systems are separated by a transmission line that can handle a maximum transfer of 550 MW in either direction. If losses are ignored, calculate the spinning reserve for the overall system and for each region. Comment on the adequacy of the spinning reserve of the overall system, and for each region. (consider the effect on the power supply in each of the regions if the various generators fail). Repeat the above calculations and analysis if an average of 8% of the output of the generators is lost in the transmission and distribution system before reaching the load.
Q1a. Explain the following terminologies: Binary State Multi State Hard failure Soft failure Q1b. With the aid of a well labelled diagram, explain the stages involved in a bathtub curve #3 The life of an automotive component can be modelled by a Weibull distribution. ∝ = 6.3?105 , ? = 1.3 Calculate F(t) R(t) h(t) at the end of rotating period of 36,000 miles Q1c How should a reliability program be organized in an environment of concurrent engineering?
Explain the importance of power system stability in maintaining grid reliability.