1- Discuss the suitable method of thermocouple calibration and show the wrongs in this experiment. 2- Sketch the curve between the thermocouple reading and thermometer reading and what we can get from the curve (find the relation between the T&V). 3- By what we can correct the readings of the thermocouple ? 4- Write a short answer a bout the method used in junction welding of thermocouple junction .

1- Discuss the suitable method of thermocouple calibration and show the wrongs in this experiment. 2- Sketch the curve between the thermocouple reading and thermometer reading and what we can get from the curve (find the relation between the T&V). 3- By what we can correct the readings of the thermocouple ? 4- Write a short answer a bout the method used in junction welding of thermocouple junction .

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the signal flow chart of the simple resistance network.a) Determine the variables.b) Establish relationships between variables (using circuit rules).c) Identify branches and nodes and draw the signal flowchart.
How does the power, P, dissipated by a resistor depend on the indicated parameter (resistance, R,of the resistor, or the voltage or current of the supply) for each of the following scenarios? I amlooking for a mathematical equation for power as a function of the indicated parameter followed bya description of the dependence - does the power increase, decrease, remain the same or some otherdependence, as the parameter is increased? (and if other, describe.) If it is increasing or decreasing,by what factor does the power change if the parameter is increased by a factor of 3?(a) Constant R, powered by ideal voltage supply (We will examine real batteries that have internalresistance in class and the next homework.) How does P depend on the voltage, V, of thesupply?(b) Constant R, powered by ideal current supply. How does power depend on the current I?(c) Ideal battery operating at a fixed voltage, powering a variable resistor R. How does P dependon the resistance, R, of the resistor?(d)…
The high-voltage power supply for a television's picture tube has an open-circuit voltage of 18 kV and an internal resistance of 1.5 MQ. (a) Find the voltage at the anode of the picture tube when the anode current is 800 µA. (b) What will the anode voltage be if the anode current is increased by 50%? (c) Find the short-circuit current of the power supply
In the Boost DA-DA converter circuit, given below; 1) Source voltage (E) value: In the voltage range [ AB ] (Volts) 2) Switching frequency (f) value: M kHz 3) Voltage between load terminals (Vload) F (Volt) 4) Capacitance value 470 (uF) 5) Pload 2 H (Watts) consumed per load The lowest L inductance value that can keep the DC-DC converter in continuous current condition under Which option do you see below as pH ? A = 10 Volts B = 19 Volts M = 23kHz F = 26 Volts H = 8 Watts
1) What is the relationship between the voltage across the power and the current? (P = I V ) 2) What are the limitations of a basic PMMC instrument? Explain how a basic PMMC instrument can be converted to an ammeter? Explain how a basic PMMC instrument can be converted to a voltmeter?
In the figure given we have u(t)=10· coswt [V]. We assume the diodesand the A-meter (A) to be ideal.a) Plot the waveform of the current flowing through the A-m in scale.b) What is the reading of the A-m, if it is moving-coil type?c) What is the reading of the A-m, if it is moving-iron type?d) Calculate the power factor of the WHOLE structure.
Apply each of diodeapproximations and determine:a. Current through D1b. Voltage across D2c. Voltage across R3 GIVEN: R1 = 2 kΩ, R2 = 1.2 kΩ, R3 = 6.8 kΩ E= 10 V D1: Si, rB = 2 Ω, rR = 220 kΩ D2: Si, rB = 5 Ω, rR = 560 kΩ DETERMING FIRST IF IT IS A FORWARD BIASED OR REVERSED BIASED THEN, SOLVE IN FIRST APPROXIMATION, SECOND APPROXIMATION AND THIRD APPROXIMATION SHOW THE CIRCUIT DIAGRAM IN EACH APPROXIMATION
A thermocouple application is illustrated in figure (a). If the measurement junction produces X2=92 mV at 2800°C and the reference junction 1mV at 24°C.then determine, 1) the net voltage for an oven temperature of 2800°C; 2) the net voltage for an oven temperature of 800°C. Note X2=92mV
Give example with aid of diagrams and explain the usage of capacitive transducer as: i) Pressure sensor ii) Displacement sensor and What are the advantages of piezoelectric compare to capacitive transducers? Provide an example of electronic device that uses piezoelectricity and explain its concept based on the type of piezoelectric effect.
What is the operation of the circuit below? Describe qualitatively
A storage battery of internal resistance of 0.4 is to be charged from a DC line. If the EMF of the battery is 12 V, what resistance must be placed in series with the battery to limit the charging current to a safe value of 4 A? What is the TPD?
A resistor of resistance ? is supplied by a battery which consists of voltage source ? in series with an internal resistance ?. Plot the power ? as a function of the resistance ? for 1 Ω < ? < 10 Ω given that ? = 12 V and ? = 4 Ω. From the resulting plot, when does the maximum power transfer occur and what is this maximum power being dissipated by the load?