Answered: 1) Draw axial force, shearing force and…

Engineering

Civil Engineering

1) Draw axial force, shearing force and bending moment diagrams for the frame shown in Fig.(1).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

ChapterD: Cable-stayed Structures

Section: Chapter Questions

Problem 9P

See similar textbooks

Related questions

Q: i dont get where that 4 multiplied comes from

A: column is used to support the floor which exerts a force of 3000 lb on the top

Q: Find the location of the centroid of the following shape: 75 mm 70 mm 12 mm I I K X ka X 35 mm + y R…

Q: The pedestal shown is formed by two concrete blocks with a circular cross section. Block A has a…

A: Diameter of block A (dA) = 0.5m = 500mmDiameter of block B (dB) = 1m = 1000mmE = 25 GPa = 25 × 103…

Q: A propped cantilever beam is loaded by a bending moment of the magnitude M3 at the point B as shown…

Q: Multiple Choice O о O 1.03 cm 1.79 cm 2.13 cm 3.72 cm

Q: Q.1 Determine the short and long term camber of SST36 having a span of 75 feet with only self weight…

A: Span of the beam (L): 75 feetSelf-weight of the beam: Creep coefficient (): 2.5Free shrinkage strain…

Q: Determine the x-coordinate of the centroid of the shaded area by integration. y I 28 | 18 25 Answer:…

Q: Consider the following axially loaded bar set of bars. The bar lengths, dimensions, sizes,…

Q: what are the possible features of a smart (innovative) construction vest in civil engineering?

A: The objective of the question is to identify and explain the possible features of a smart…

Q: Q (5-4) / Water flows uniformly in an earth trapezoidal cross section open channel. Data available…

Q: Two squirrels are sitting on the rope as shown. The squirrel at A has a weight of 1.2 lb. The…

Q: 10. A vertical storage tank with a hemispherical bottom and a cylindrical shell of 4 m inside…

Q: B. Find the weighted unit cost per square meter for the project data shown and determine the cost of…

A: The cost of weighted cost per sq.m of different projects are given as follows

Q: Two drivers each have a reaction time of 2.5 seconds. One is obeying a 90 km/h speed limit, and the…

A: Reaction time of both the observer = 2.5 sec Velocity of car ( obeying speed ) = 90 km/h Velocity of…

Q: A steel cantilever beam, of length 21, has an I-section, see Figure Q3. The cantilever beam is under…

Q: The system in the figure is in balance. A load of 1600 kg is suspended frompoint C on the cable…

A: The objective of the question is to calculate the forces in the AC and BC cables when a load of 1600…

Q: Determine the reactions at the supports A, B, and C, then draw the shear and moment diagrams. El is…

Q: Problem 2) Determine the maximum compressive force developed in member HG of the side truss due to…

A: Determine the maximum comprehensive force in the member HG.

Q: (b) Rate the following types of embankment damy (frour the best (1) to the worst (4)) based on…

A: We need to rate the different types of given embankment based on safety and economic considerations.…

Q: Problem 11.9 The cube of material shown in Problem 11.8 (reproduced below) is subjected to a pure…

Q: Determine the moment of inertia of the z-section as shown in the figure about its; a. centroidal…

A: Draw the figure.

Q: Draw the shear and moment diagrams for the frame shown in Fig. Assume A is a pin, C is a roller, and…

A: A frame structure is given as per the figure belowneed to find the shear force and bending moment…

Q: 4. The water discharge through the 200 mm pipe shown is throttled to a velocity of 2.4 m/s by means…

A: delivery pipe diameter= 200 mmsuction pipe diameter = 300mlength of suction pipe = 30 mvelocity =…

Q: SCENARIO The Client who is a private investor needs a 5 storey, framed college building. The…

A: The objective of the question is to determine the most suitable type of foundation for a five-storey…

Q: In the figure, the rectangular foundation is loaded with a uniform load of 225 kPa. Accordingly,…

A: Uniform load acting on foundation, depth below point A where stress is to be calculated,

Q: 0.) Girder factor at joint D, go b.) Column factor at joint K, Ck

A: All data present in the figure as given belowNeed to find a) Girder factor of joint D, go b) Column…

Q: 11. From the figure shown, the tank contains oil having a sg = 0.82. Oil flows at a certain rate…

A: specific gravity of oil(s) =0.82fluid head = 2.8 m power (P) =9 hpDiameter of orffice =80…

Q: If the model In us = In uf-k/kj is applicable to depict the correlation between speed (mi/h) and…

Q: line and Tous line in llowing contour figure indicate Both are valley line 240 Ridge line and valley…

A: Given ContoursTo find out What is dotted and dark lines

Q: PLATE 1: ANALYZE THOROUGHLY THE DIAGRAM OF THE GIVEN FRAME. DRAW THE DIAGRAM OF EVERY ANALYZED PART…

Q: The deflections at point D and C of the given beam will be: A 2 MN/m 2 m 8 MN-m D 2 m B O Sale M M…

Q: Discuss the classification of cross sections as per the IS 800: 2007 based on yield and plastic…

A: The objective of the question is to understand the classification of cross sections as per the…

Q: SAND DAM FLOW IMPERVIOUS ROCK B = 240 FT 30 FT T= 20 FT The total length of the dam shown is 800 ft.…

Q: REACTION OF A RIGID PLATE II A) Determine the internal and external reaction forces of a composite…

A: Determine the internal and external reaction forces of a composite structure. To check the solution…

Q: Summarize the merits of HSFG bolts

A: The objective of the question is to understand the advantages or merits of High Strength Friction…

Q: Design an I section purlin for an industrial building with Galvanized iron sheets as the roofing…

A: Span of the truss (L): 14 mSpacing of trusses (St): 7 m c/cSpacing of purlins (Sp): 1.3 m c/cWind…

Q: A 10-m-wide rectangular canal carrying a discharge of 18 m³/s, where the flow is moving at a…

A: Width of rectangular channel (B) =10mDischarge (Q) =18 m³/sVelocity of flow (V) =6m/s

Q: For the structure shown in Figure (4): Draw I.L for (RA), (RC), (VB), (VD) and (MD) 39 5 Figure (4)…

Q: The same forces act on two objects having the same masses. The more massive object will experience…

Q: Given a design speed of 70 km/h, a horizontal curve radius of 550 m, a road platform width of 10…

A: design speed = 70 km/h horizontal curve radius = 550 m a road platform width = 10 minitial slope =…

Q: = A steel cantilever beam, of length 2L, has an l-section, see Figure Q3. The cantilever beam is…

Q: Question 6 Given the model expressing the connection between speed (mi/h) and density (veh/mi) on a…

A: Given Speed relationship with densityTo find out Density at Maximum flow

Q: Determine the maximum tensile and compressive bending for the beam shown. (xyz = 630) Young's…

A: A cantilever beam is loaded as followsuvl is 0 at free end and 630plf at fixed end.

Q: 1. For a constant head laboratory permeability test on a dine sand, the following values are given:…

Q: The structure below is made to handle a maximum normal stress of 90 MPa. Determine whether it can…

A: allowable normal stress, σ = 90 MPa

Q: Consider two ocean ridge segments connected by a transform fault: (b) = ridge 100km. transform fault…

A: The given values are as follows:

Q: 1. Pipelines 1, 2 and 3 are connected with parallel to each other with pipeline 1 having diameter of…

A: Pipe 1 : D1 =450mm and L1 = 600mPipe 2 : D2 =400mm and L2 = 800mPipe 3 : D3 =500mm and L3 = 700mf =…

Q: 7) The floor of a weir is 20 m long with two sheet piles of 5 m at the downstream end and 4.5m at…

A: b = 20mH = 3.9mL1 = 4.5mL2 = 5m

Q: For a soil specimen, given the following: % passing sieve #4 - 92%, sieve # 10 - 81%, sieve #40=78%,…

A: %passing sieve #4 = 92%%passing sieve #10 = 81%%passing sieve #40 = 78%LL = 48%PL = 16%GI = 18.2

Q: If the model in us = In uf-k/kj is applicable to depict the correlation between speed (mi/h) and…

Concept explainers

Frames

The trusses and frames are the two most important structural members of civil engineering. Trusses are the interconnection of links and other structural members. The interconnection with other members makes the system behave as a single member that supports and transfers loads. Trusses are generally two types, plane truss, and space truss. Frames on the other hand form the skeleton of any building construction. Frames are structures formed by the connection of beams, columns, slabs, and joists. These members provide the building with the required structural support.

Question

Q1) Draw axial force, shearing force
and bending moment diagrams
for the frame shown in Fig.(1).
La
10KN/
Fig.(1)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation of Reaction forces

VIEW

Step 3: Calculation of axial force, shear force, bending moment for different segment

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the reactions and draw the shear and bending moment diagrams for the beams shown by using the slope deflection method. PLEASE REFER TO FIG. P16.3
Q1:Draw axial ,shear force and bending moment diagrams for the following structures in fig1 and 2 9kN 9kN 9kN/m 2.5m 2.5m 2.5m Figure 2)
Determine the shear and bending moment at point B of the beam shown in Fig. 5.4.
2 In the beam ABC shown in Fig. P.16.32 the support at B settles by 10 mm when the loads are applied. If the second moment of area of the spans AB and BC are 83.4×10° mm“ and 125.1x10° mm“, respectively, and Young's modulus, E,of the material of the beam is 207000 N/mm², calculate the support reactions using the moment distribution method. Ans. Rc=28.6 kN, Rg=15.8 kN, RA=30.5 kN, MA=53.9 kNm.
Q 1: 1- Determine the x-y and n-t components of the 65 kN force F (F1, Fy, Fn, F1) acting on the simply-supported beam as shown in Fig. 1. 2- Find the vector components (F: & F;) of ; the force F onto the non-perpendicular axis x-t. F= 65 kN 40 B 3 m 5 m 16° 15 X- Fig. 1
706. For the propped beam shown in Fig. P-706, determine the reaction R and sketch the shear and moment diagrams. wo conjugate beam method Figure P-706 R
Determine the reactions and draw the shear and bending moment diagrams for the three-span continuous beam shown in Fig. 15.6(a) by the slope-deflection method.
(c) Determine the location of the shear center O of a thin-walled beam of uniform thickness having the cross section shown in Fig. Q2(c). Hint: Use polar coordinate Integrate M₁ = с arc at x = r sin a A cross-sectional area, I = α Fig. Q2(c) system and cos 20=1–2 sin² 0 . adF = ar dA, J = Aa² where A is the ατ A J == T = 2 2 a VQ It C and McVe. Centroid of Fig. Q3 α Ο
Q. 1: For the beam and loading shown in Fig. Q1 a) Draw the free-body diagram (FBD) and determine the reactions at supports A and B. b) Derive the expressions for shear forces (SF) in each appropriate section. c) Draw the shear force (SF) diagram of the beam. d) Derive the expressions for bending moments (BM) in each appropriate section. e) Draw the bending moment (BM) diagram of the beam. f) Determine the magnitude and location of the maximum absolute value of the bending moment. y A IIII 4 m 6 m 30 kN Fig. Q1: A loaded beam. B X
Determine the reactions and draw the shear and bending moment diagrams for the two-span continuous beam shown in Fig. 15.5(a) by the slope-deflection method.
Q2-Draw the shear force and bending moment diagrams for the beam shown in Fig. (2)
Q2. Draw the shear force and the bending moment diagrams for the compound beam shown in Fig. Q2. 10 KA/m WY 6m 77777 2m 2m * km 20KN/m OC *