1- In a buck DC/DC converter: V₁ = 100 V, R= 8M, D= ton = 0.8, f == 20000 Hz, L = 200 µÍ, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd C1 www + V₂

1- In a buck DC/DC converter: V₁ = 100 V, R= 8M, D= ton = 0.8, f == 20000 Hz, L = 200 µÍ, Find: a) average voltage and current of the load Vala. b) maximum and minimum current of inductor. c) Voltage ripple of the capacitor. d) the average input current. e) draw the figure of the inductor current. C1 = 40 Micro farad Q Vd C1 www + V₂

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 2PA: You are working in an industrial plant. You have been instructed to double the capacitance connected...

See similar textbooks

Similar questions

You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
Q.1. A power suppply having 220 V AC input and two fixed outputs as 10 V DC and 20 V DC is requested from you. For this purpose, a transformer with 220 V AC input / 15 V AC output, some capacitors, some silicon diodes, and zener diodes are presented.a) Design your power supply and point out DC voltage outputs b) Explain the operation of the network and all the components used in the design .c) Calculate and plot input and output signals of the network.Hint: For design, remember clipper, clamper, rectifier,voltage multiplier and zener circuits
A buck converter is supplied from a 50V battery source. Given L=400uH, C=100uF, R=20 Ohm, f=20KHz and D=0.4. Calculate: (a) output voltage (b) maximum and minimum inductor current, (c) output voltage ripple
low voltage systems What is the general reason for selecting the capacitor voltage with a value greater than 400 V (such as 415,445 V) in Reactive Power Compensation? a) Reduce losses b) Harmonics C)Current decrease d) Voltage drop
Design a buck converter that converts input DC 50 V to output 30 V/1 A. (Specifications: Inductor current continuous, output ripple voltage effective 10 mV or less, input 50 Vdc, output 30 Vdc/1 A)
Electrical Engineering --question 1-- Calculate the theoretical voltages across the resistor and inductor for 10 kHz and 60 kHz using the 680Ω theoretical resistance, 3.3 mH inductance, and 5-V source. Demonstrate the step-by-step process. Answer must be in Polar form. --question 2-- Calculate the theoretical voltages across the resistor and capacitor for 500 Hz and 1750 Hz using the 680Ω theoretical resistance, the observed capacitance, and the 5V source. Demonstrate the step-by-step process. Answer must be in Polar form.
Q) Design a boost PWM converter to meet the following specifications: V;=30V, Vo=270V, R, =480 Q, f: =25 kHz, V,/Vo < 1%. Find L, C, minimum inductor current /y(min), maximum inductor current /y(max), and output power. Qa)
In the circuit given in the figure, calculate the IC current by full analysis, since |VBE| = -0.7V, R1 = 2.66Kohm, R2 = 11.73Kohm, RC = 0.79Kohm, RE = 2.36Kohm, VCC = 14.00V, Beta = 115.00.
Please solve this problem in detail A step up DC converter is used to control power flow from a DC votage Vs = 100V to a battery voltage E = 200V. The power transferred to the battery is 20 kw. The current ripple of the inductor is negligible. The duty cycle and the effective load resistance as seen from the input are respectively equal to: Select one: a. None of these b. 0.5, 0.5 Ohms c. 0.33, 0.5 Ohms d. 0.5, 0.33 Ohms
With reference to the attached circuit image: If the capacitor is now removed from the attached circuit and is placed in parallel with the secondary of the transformer. A) What is the impedance seen at the supply (HV side) B) What is the power dissipated by the tube
Draw a circuit diagram for a series circuit containing a R = 100-ohm resistance, a coil with L = 0.1 H inductance, and a C = 20-micro-F capacitor connected across a 110-V, 60 Hz voltage source. What will be the current (I) through the supply and the phase angle between current and the source? You tried to draw a circuit diagram for a series circuit containing a R = 100-ohm resistance, a coil with L = 0.1 H inductance, and a C = 20-μF capacitor connected across a 110-V, 60 Hz voltage source. What would be the voltmeter readings across R, L, and C? (Show your work on scratch papers). Show your work in calculating the resonance frequency of a circuit containing an inductance L = 40.0 mH and a capacitance C = 600 pF