1-Moment of inertia of the pulley (kg.m2) ? 2-tension in rope of m1 (N) ? 3-tension in rope of m2 (N) ? 4-angular acceleration of the pulley (rad/s2) ? 5-acceleration of block m1(m/s2) ? 6-acceleration of block m2 (m/s2) ?

1-Moment of inertia of the pulley (kg.m2) ? 2-tension in rope of m1 (N) ? 3-tension in rope of m2 (N) ? 4-angular acceleration of the pulley (rad/s2) ? 5-acceleration of block m1(m/s2) ? 6-acceleration of block m2 (m/s2) ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Block C starts with initial velocity 0.4 m/s and moves down with a constant acceleration. Knowing…

A: Given:- Initial velocity (vi) of block C with constant acceleration = 0.4 m/s Movement of Block B =…

Q: 3. The ball is kicked from point A with the initial velocity va 10 mis. Determine the range R and…

A: Given, vA=10 m/s

Q: select three different vertical positions to hit the block and determine the required velocities to…

Q: +r

A: Vr = r , Vr = 4000 ft/s Vq = rq , Vq = 25 X 104 (0.8 X π/180) = 3490 ft/s V = √Vr2 + Vq2 V = √40002…

Q: Q3/ The ball is kicked from point A with the initial velocity VA = Determine the range R, and the…

A: The above problem is approached with the projectile motion, when the object is thrown it subject to…

Q: Q5/A sphere is fired downwards into a medium with an initial speed of 45 m/s. If it experiences a…

Q: For these conditions determine the velocity of the rocket v, the acceleration of r ar and angular…

Q: Determine the minimum speed of the stunt rider so that when he leaves the ramp 4) at A he passes…

A: Maxm height required to pass through. the loop h = 3.5 m h = v∘2 sin2o2g ⇒ v∘…

Q: 1. The 0.5-kg ball strikes the rough ground and rebounds with the velocities shown. Determine the…

Q: The drag racer P starts from rest at the start line S and then accelerates along the track. When it…

Q: The rotating arm starts from rest and acquires a rotational speed N = 600 rev/min in 2 seconds with…

A: Solution; Given data; Speed of arm, N=600rev/min Time, t=2sec Angle, θ=45° Distance between O and P,…

Q: Q1:- How many 32 m diameter parachutes (CD=1.2) should be used to drop a bulldozer weighing a 100 kN…

A: Terminal velocity When drag equals weight, the object experiences no net external force and its…

Q: The belt-driven pulley and attached disk are rotating with increasing angular velocity. At a certain…

A: Determine (a) the angular acceleration of the pulley and disk, (b) the total acceleration of point…

Q: The coefficient of friction between the 50 Ib weight and the 300 Ib weight is 0.5. The 300 lb weight…

A: When anybody on the mechanics moves on the surface, the surface gives the resistance force termed…

Q: A 97-ft3/s water jet is moving in the positive x-direction at 18 ft/s. The stream hits a stationary…

Q: A rotating flywheel of 200-mm radius is braked by the device shown. If coefficient of friction is…

Q: A car is to be hoisted by elevator to the fourth floor of a parking garage which is 32.35 ft above…

Q: The crate has a mass of 80 kg and is being towed by a chain which is always directed at 70° from the…

Q: Aeroplane A is moving in Eastern direction with a speed of 540 km/hr and a deceleration of 94…

Q: 12-77. The car travels from A to B, and then from B to C, as shown in the figure. Determine the…

Q: 2.0 ft 5 AO 10.0 ft E 30° 0.5 ft

A: Given Data Velocity at E is : VE = 12 ft/s Acceleration of gear A is :aA = 2 ft/s2 Now the…

Q: Q3: A tank containing water upto a depth of 500 mm is moving vertically upward with a constant…

A: GivenDepth, h=500mm=0.5mAcceleration, a=2.45 ms2 same for both directionWidth=2m

Q: A football player releases a ball with the initial conditions shown in the figure. Determine the…

A: Given data, Vo = 86 ft/sec θ = 40° g = -32. 2ft/s² To find out the radius of curvature of…

Q: The boy A is moving in a straight line away from the building at a constant speed v4. The boy C…

Q: Aeroplane A is moving in Eastern direction with a speed of 540 km/hr and deceleration of 94 km/hr'.…

A: Ans is given below

Q: The position of the slider P in the rotating slotted arm OA is controlled by a power screw as shown.…

A: given θ˙ = 5.4 rad/s θ¨ = -35 rad/s2 r = 396 mm = 0.396 m r˙ = -251 mm/s =.251 m/s r¨ = 0.

Q: q1 A M1 M2 L3 L3 L3

A: M1=189kNm M2=168kNm L3=3.5m

Q: 3. The o.5-kg ball strikes the rough ground and rebounds with the velocities shown. Determine the…

A: The ball strikes the ground at an angle of 45. We will have to take the vertical component of…

Q: Required: Find the uniform acceleration in ft/s-. Be sure to note the sign/direction (+ or -).

Q: Two elevations A and B which operates adjacent to each other, are approaching each other from an…

A: We have to determine the value of time when elevator pass each other and distance travelled by…

Q: Without actually solving the centroidal moment of inertia about x-axis, how will you tackle this…

A: The given section can be considered as shown below: Where, 1 - I section 2, 3 - Rectangular box

Q: F12-16. A particle is traveling along the straight path. If its position along the x axis is x =…

A: Given data : Time=t t=2 s Position of particle along X axis =x x=8×t m Position of particle along Y…

Q: Question 3: Determine the maximum constant speed at which the pilot can travel around the vertical…

A: When the airplane moves in along the vertical curve it experiences centrifugal force and self weight…

Q: CG H = 0.5 H = 0.6 Required: 1. Maximum angle theta that will move the car on the inclined plane…

A: Given data μs=0.5μk=0.5Gross weight ,MN=55Assumeθ=Maximum angle that will move the car onn the…

Q: The jeep has a weight of 2700 lb and is travelling forward at 4.563 ft/s when it crashes onto the…

A: Given,W=2700 lbu=4.563 ft/st=0.06sμk=3assuming μk=0.3as coefficient of friction can never be more…

Q: 2. The car travels up the hill with a speed of v= (0.2 s) m/s, where s is in meters, measured from…

A: Given data Speed of the car =V=0.2sm/sRadius of the curvature=p=500 ms=50 m Calculate the the…

Q: (Q6] At this instant , find angular acceleration and angular velocity for BC using - Absolute motion…

A: Step 1

Q: Block B rests upon a smooth surface. If the coefficients of static and kinetic friction between A…

Q: A tracking radar lies in the vertical plane of the path of a rocket which is coasting in unpowered…

A: Given- θ=30°r=25×103 ftVr=4000 ft/secω=0.80deg/seca0=31.4ft/sec2

Q: QI: The skateboard rider leaves the ramp at A with an initial velocity Da at a 30* angle If he…

A: The given figure is shown below:

Q: Aeroplane A is moving in Eastern direction with a speed of 540 km/hr and a deceleration of 94 km/hr.…

A: Relative acceleration and velocity is given below

Q: Q2. The rotation of the 0.9-m arm OA about O is defined by the relation U= 0.35f, where U is…

A: The given data is:

Q: Which minimum initial velocity vo in position 0 is necessary, such that the body with mass m reaches…

Q: Q1. Given the eulerian-vector field V= 4x2i – 10x?yj + 2tk find the velocity and the resultant…

Q: The disk starts at @_0 = 1 rad s^-1 when 0_0 = 0, and is given an angular acceleration α = 0.3 0 rad…

Q: 5 km/hr. If the driving force acting on the van is FD = (500) N which acts e minivan for 4 seconds…

A: we know that, from Newton's 2nd law of motion, Force = change in momentum with change in time.…

Q: Determine the angular velocity e in rad/s of the radial line OA at this instant if the truck has a…

Q: A ball is thrown with an initial velocity of 100 ft/s upward at 60° with the horizontal. When the…

A: Whenever an object is launched in the air, it is said to have an projectile motion. When an object…

Q: The two attached pulleys are driven by the belt with increasing speed. When the belt reaches a speed…

A: Given:- Two pulleys are driven by the belt The speed of the belt (v) = 1 ft/sec The total…

Question

1-Moment of inertia of the pulley (kg.m²) ?

2-tension in rope of m₁ (N) ?

3-tension in rope of m₂ (N) ?

4-angular acceleration of the pulley (rad/s²) ?

5-acceleration of block m₁(m/s²) ?

6-acceleration of block m₂ (m/s²) ?

A pulley has a mass 18.6 kg and having a radius of gyration of 0.93 m. is connected
to two blocks (m1=12.4 kg , r=0.62 m , m2=4.96 kg , and R=1.24 m) as shown.
G
r-
В
m2
m1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A compound shaft consists of a titanium alloy [G = 6,200 ksi] tube (1) and a solid stainless steel [G = 11,500 ksi] shaft (2). Tube (1) has a length of L1 = 40 in., an outside diameter of D1 = 2.05 in., and a wall thickness of t1 = 0.120 in. Shaft (2) has a length of L2 = 54 in. and a diameter of d2 = 1.05 in. If an external torque of TB = 580 lb·ft acts at pulley B in the direction shown, calculate the torque TC required at pulley C so that the rotation angle of pulley C relative to A is zero.
Determine the displacement at pulley B. The A992 steel shaft has a diameter of 30 mm.
The boom in the figure supports a load W = 1400 lb. Compute the forces in the cables AE and BD and also the components exerted by the ball and socket joint C. Answers: AE = 512 lb; BD = 878 lb; CX = -250 lb; CY = 600 lb; CZ = 800 lb
For the riveted bracket shown in the figure below. P = 250 kN. The rivets have diameter of 25mm. The connection can be analyzed by replacing the given load with an equivalent loading composed of a vertical force along acting through the centroid of the rivets and a moment. 1. Which of the following most nearly gives the shearing stress in each rivet due to the vertical force alone acting at the centroid? a. 127.3 MPa b. 145.6 MPa c. 112.8 MPa d. 186.4 MPa 2. Which of the following most nearly gives the shearing stress in rivet D in MPa? a. 134.7 b. 113.9 c. 85.6 d. 156.7 3. Which of the following most nearly gives the stress in rivet B when the instantaneous is 200 mm to the left of cg, in MPa? a. 274.5 b. 341.8 c. 389.6 d. 187.5
Replace the three forces acting on the guy wires by a single force acting on the flagpole. Use T1= 200 lb, T2= 400 lb, and T3= 350 lb.
AS SHOWN IN THE FIGURE, A RIGID BEAM WITH NEGLIGIBLE MASS ISPINNED AT ‘O’ AND SUPPORTED BY TWO RODS IDENTICAL EXCEPT FORLENGTH. A = 100 mm2 & E = 200 GPa. DETERMINE THE LOAD IN EACHROD IF P = P3
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
Two 10"-15.3 lb channels are welded together as shown in the figure. Find the moment of area of the upper channel about the horizontal centroidal axis Xo of the entire section.
A frustum of rectangular pyramid is immersed in water by anchoring it to the bottom ofthe seabed. The dimension of the base of pyramid is 4 m x 6 m and the height of frustumis 3 m. The lower base of the frustum is thrice of the upper base. The mooring line wasobserved to have a tension of 12000 N. Evaluate the specific weight of the frustum inkN/m3.
The crane and boom shown in Fig. P6-69 weigh 12,000 lb and 600 lb, respectively. The pulleys at D and E are small, and the cables attached to them are essentially parallel. determine the location of the resultant force on the thread relative to point c when the load lifted is 3600 lb (consider the fbd of the system) maginitude of the pin reaction at boom support A when the lifted load is 3600 lbs. (consider fbd of pulley b and fbd of boom ab)
GI, GE, and GD of the cage system for the loading condition given in Figure 2 Calculate the rod forces. tensile or tensile rod forces Specify the pressure. P1(kN)=20 P2(kN)=45 L3(m)=7
Q#3. An aluminium strut 14 ft long has a rectangular cross section 1.5 in by 3 in. A bolt through each end secure the strut in such a way that is acts as hinged column about an axis perpendicular to 3 in dimension; and as fixed column about an axis perpendicular to 1.5 in dimension. Determine the safe central load with a factor of safety of 2.5 and E= 10300000 psi. Also discuss in detail about the governing column capacity and reasons behind it.