The supporting wheel on a scaffold is held in place on the leg using a 4-mm-diameter pin as shown.(Figure 1)Figure1of1 >Part AIf the wheel is subjected to a normal force of P=2.5 kN, determine the average shear stress developed in the pin. Neglect friction between the inner scaffold puller leg and the tube used on thewheelExpress your answer to three significant figures and include the appropriate units.Templates Symbols undo resto resel keyboard shortcuts HelpTag = 99.471mpqSubmitPrevious Answers Request AnswerProvide FeedbackNext >

Answered: Image /qna-images/answer/e906d51a-91e2-4715-8287-5c9570e4af5a.jpg

1 of 1 If the wheel is subjected to a normal force of P = 2.5 kN, determine the average sh wheel Express your answer to three significant figures and include the appropriate un Templates Symbols undo reto resel keyboard shortcuts help Thug - 99.471 mpq Submit Previous Answers Request Answer Provide Feedback

1 of 1 If the wheel is subjected to a normal force of P = 2.5 kN, determine the average sh wheel Express your answer to three significant figures and include the appropriate un Templates Symbols undo reto resel keyboard shortcuts help Thug - 99.471 mpq Submit Previous Answers Request Answer Provide Feedback

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The stepped shaft shown rotates at 480 rpm. Knowing that r = 0.2 in. and using figure 3.28, determine the largest torque T that can be transmitted without exceeding an allowable shearing stress of 7000 psi.
A solid constant-diameter circular shaft is subjected to the torques of TA = 460 lb·ft, TB = 1000 lb·ft, TC = 880 lb·ft, and TD = 340 lb·ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in Section 6.6. (b) If the allowable shear stress in the shaft is 7200 psi, what is the minimum acceptable diameter for the shaft?
For the shaft shown, a. Determine the maximum stress on the shaft and the maximum angle of twist of end D relative to end A. b. If the stress in every section must not exceed 25 MPa, what should be the uniform diameter of the shaft? dAB = 100mm, dbc = 80mm, dcd = 50mm G for the shaft is 80GPa. Consider clockwise torques as negative.
For the beam shown, determine the support reactions and draw the stress diagrams.shear and bending moment. EI is constant. Use the force method. I have a correct answer, it is: VA = 44.3 kN (↑); HA = 0 kN; MA = 34.3 kN.m (counterclockwise); VB = 38 kN (↑). I don't know how to get to this result, please show me how to get there step by step
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
3.Figure (a) shows a rigid bar that is supported bya pin at A and two rods, one made of steel and theother of bronze. Neglecting the weight of the bar,compute the stress in each rod caused by the 50-kN load, the following data：
A rigid bar, hinged at one end, is supported by two identical springs as shown. Each spring consists of 20 turns of 10-mm wire having a mean diameter of 150 mm. Compute maximum shearing stress in the springs. Neglect the mass of the rigid bar.
The steel shaft of a socket wrench has a diameter of 8.0 mm. and a length of 200mm (see figure). If the allowable stress in shear is 60 MPa, what is the maximum permissible torque Tmax that may be exerted with the wrench? Through what angle f (in degrees) will the shaft twist under the action of the maximum torque? (Assume G=78 GPa and disregard any bending of the shaft.)
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
Question-04: Solve for the torque T that can causes a maximum shearing stress of 4.2 ksi in the cylindrical steel shaft as shown in Figure 3. Assume radius of the shaft r = 1.2inches.
From the given figure below and its properties, calculate the stress at the top where the maximum moment is located. (MPa) Properties: Beam width = 207 mmBeam height = 386 mmWLL = 12.48 kN/mWDL = 15.26 kN/mSpan of the beam = 8 mPrestressing force = 293 kNeccentricity = 135 mm