1 Sketch the Root Loci of following unity feedback system And find the following Ris) + K(s+ 3) s(s + 1)(s + 2)(s + 4) And find the following points: a) Asymptote center. b) Angles of asymptote. c) Find the range of K using Routh table. d) The breakaway and the break-in points.

1 Sketch the Root Loci of following unity feedback system And find the following Ris) + K(s+ 3) s(s + 1)(s + 2)(s + 4) And find the following points: a) Asymptote center. b) Angles of asymptote. c) Find the range of K using Routh table. d) The breakaway and the break-in points.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Example 2: Obtain step response of a unity feedback system having forward path 1 transfer function…

Q: Consider the following feedback system, 1 R(s) Y(s) s(s+a)(s +s+1) (a) Find the sensitivity of the…

Q: Given a unity feedback system with G (s) =K/ s (s+4). What is the value of K for a damping ratio of…

A: Given: Transfer function is Gs=K/ss+4 Feedback is unity Hs=1 Damping ratio is ζ=0.5

Q: Q6: Consider a linear system described by the T.F, Y(s) %3D 10 U(s) s (s+ 1)(s+2) Design controller…

A: According to the question, the transfer function of a linear system is described by YsUs=10ss+1s+2;…

Q: QUESTION 4 Consider the root locus of a unity feedback system that has the open loop transfer…

A: Angle of departure is calculated whenever we have complex poles. Mathematically it is defined as…

Q: 1. Given the unity feedback systems shown, analyze its stability using Routh-Hurwitz criterion.…

Q: b) What are the effect of negative feedback on gain and bandwidth? Confirm your answer by drawing…

A: The answer as given below:

Q: Q3] Sketch the root Locus of the unity-feedback system whose open-loop transfer function is given…

A: Given An open loop transfer function. We need to determine the No of poles and zeroes,locate…

Q: a) Consider a feedback amplifier with the following open loop 1018 BA = Gf + 104)jf + 104)(jf + 106)…

A: Part (a): (1): Consider the open-loop transfer function, BA=1018jf+104jf+104jf+106 The Bode plot for…

Q: 1. Given a unity feedback system that has the forward transfer functie k(s+2) G(s) = s²(s² +4s+13)…

Q: 16. For the unity feedback system of Figure P8.3, where K G(s) s(s + 6)(s +9) plot the root locus…

A: Given that, G(s)=K / s(s+6)(s+9) Pole: 0,-6,-9 P-Z=3 Root locus exist between s=-6 to s=0…

Q: s+10s + K,s²+2s + K2 = 0. where K and K, are feedback gain factors. Determine and plot the region of…

Q: Figure 1 shows a unity feedback system where the transfer function is given as 1 G(s): s(s² + 100s…

Q: The circuit as shown is a shunt-shunt feedback amplifier. Use feedback analysis to find the midband…

A: The equivalent circuit diagram for the given shunt-shunt feedback amplifier is shown in the…

Q: Frequency (rad/s) Find the phase margin &M, and the gain margin GM in dB. Is the negative unity…

A: The state-space form of a system is given below,x˙ = 12-4-5x + -10uy = 21x + 0·u

Q: True and False (correct the false) Class -A: the output stage conducts for a full 360° (a full…

A: 1) Class A output stage conducts for a full 360° because Q point lie on mid of load line TRUE 2)…

Q: An op amp has a dc gain of 100 dB and a unity-gain frequency of 10 MHz. What is the upper-cutoff…

A: Given data: The value of dc gain is: 100 dB The value of unity-gain frequency is: 10 MHz The value…

Q: Given the unity feedback system of Figure P8.3, make an accurate plot of the root locus for the…

A: we need to calibrate the gain for at least four points for each case. Also find the breakaway…

Q: Ex. 430. G(s)=k (s+3)/(s(s+ 4)(s+ 5)) is the forward transfer function of a unity feedback…

A: The root locus is the plot of location of poles of the closed loop transfer function by varying the…

Q: QUESTION 5 A unity feedback system has the open loop transfer function shown below. Use the Nyquist…

Q: Find steady state error for ramp input, system type, Kp, Kv, and K. for the following non-unity…

A: In this question the given system have non unity feedback so we convert it having unity feedback .…

Q: Consider a unity feedback system with a forward transfer function, G(s) = = K s(s+ 2)(s + 10) (a)…

Q: Given that a feedback network is shunt-series, and output load is 10kΩ, what is the output voltage…

Q: Problem: Given the following 2nd feedback system with step input u(t). First, determine its…

Q: 3. gain to 70.7% of its midrange value. --- Frequencies are values of frequency at which the RC…

A: 3. Cutoff frequencies are values of frequency at which the RC circuits the voltage gain to…

Q: A unity feedback system has an open loop function G(s) = s(s+2)(s+4) Make a rough sketch of root…

Q: Determine the transfer function using Mason’s Rule: (note: -H3(s) and -H2(s) for feedbacks)

A: Mason gain formula is ∑k=1npk×∆k∆ ∆=1-(sum of the Product of gains of individual loops)+(sum of the…

Q: Fuels True the feedback path in closed loop system representation by r(t) The numerator polynomial…

A: 1. False, The feedback path in closed loop system is represented by H(s) 2. True, The numerator…

Q: (b)- For a feedback system G-k, G,-1/(s'+6s+12) and H=s+2, k20. (bl)- sketch the Root Locus (RL)…

A: The Given Feedback system Gc=k Gp=1s2+6s+12 & H=s+2,k≥0. To sketch the root locus RL To find…

Q: Q6: For a unity feedback system with G(s) =- do the following: s(s+5)(s+11)’ a. Find the gain K,…

A: Unity feedback system is given as, Gs=Kss+5s+11 Formula for percentage overshoot, μp=e-Cn1-c2×100…

Q: Consider the root locus of a unity feedback system that has the open loop transfer function shown…

Q: R(s) + E(s) V(s) N(s) K P(s) We want to design a speed control for a DC motor. The transfer function…

A: We need to find the value of compensator K

Q: R(s) + E(s) Σ V(s) (s) K P(s) We want to design a speed control for a DC motor. The transfer…

Q: 8.1 Given find the state feedback gain k so that the state feedback system has -1 and -2 as its…

A: Given state representation shown X˙=21-11X+12uy=11XThe desired eigen values are -1 and -2

Q: Consider the ideal op-amp based circuit shown in the figure below: R The transfer function of the…

A: Given circuit is - Given values are - VosVis=-10sR=1mega ohm=106Ohm

Q: Consider a unity feedback system with forward path transfer function: 360 360 G(s) = (s + 3)(s +…

A: Brief description: State space representation is not unique depending upon the requirement we can…

Q: 117 Q.1 - The open loop transfer function for a unity - feedback system is and S? +8S r(t)=3t…

A: The Block diagram reduction technique is used to determine the transfer function of complex control…

Q: For the open loop transfer function shown below, sketch the Nyquist plot and then check the…

Q: 5.1 Determine the transfer function C/R for the system below using signal flow graph. K is constant.…

A: The given block diagram can be converted into the signal flow graph by considering the summing point…

Q: 5. The forward transfer function of a control system has no zero and three poles at 0, 0, and -5 and…

Q: A unity feedback system with its forward transfer function G(s) = K(s+a)/s(s+B) is to be designed to…

A: The solution is given below

Q: K Q6: For a unity feedback system with G(s) = do the following: s(s+5)(s+11)' a. Find the gain K,…

A: Given unity feedback system with G(s) = k/s(s+5)(s+11) And by considering the given factors…

Q: 13. Given the unity feedback system of Figure P6.3 with 84 G(s) = s(s7 + 5s6 + 12ss + 25s4 + 45s3 +…

Q: Sketch the root locus plot of unity feedback system with an open loop transfer function k s(s+5)(s+…

A: Referring to the given transfer function, here number of poles are 3 and number of zero are 0.…

Q: 10- A unity feedback system has open-loop transfer function G(s)=2/ (S+4), the ratio of time…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: Problem 2: The following is the open-loop transfer function for a unity- feedback discrete system…

A: Given open loop transfer function for a unity feedback discrete system Changing z-domain into…

Q: Example 2: Obtain step response of a unity feedback system having forward path transfer function of…

Question

1 Sketch the Root Loci of following unity feedback system
And find the following
K(s + 3)
s(s + 1)(s + 2)(s + 4)
R(s) +
C(s)
And find the following points:
a) Asymptote center.
b) Angles of asymptote.
c) Find the range of K using Routh table.
d) The breakaway and the break-in points.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

: It is known that the lower cutoff frequency value is 63.66 Hz and the bandwidth value is 381.97 Hz in the circuit with Op-Amp in the figure. According to the element values and connection information given in the circuit, R1=?
Q-4. How many op-amps are required to implement this equation? V1+ R2 V. =- A) 3 B) 4 C) 2 D) 1 Q- 5. For the following feedback circuit. Identify the type of feedback and find the closed loop gain. E A ► VOUT
Six similar attenuators are used in an audio design and are linked in a cascade. The total attenuation is 80 decibels. The first section of the attenuator circuit has a 20 mV input. Determine (i) the attenuation in decibels provided by each individual attenuation stage, (ii) the output in volts of the final stage (iii) the output in volts of the fifth stage.
4. Design a clipper circuit which limits input signals to +3V and -2V. This means that the output signal should not rise above 3V and should not fall below -2V. Assume Vs has amplitude of 5V and a frequency of 1 kHz, Verify your design by computer simulation on a computer.
5. Consider the following Bode diagrams for the loop gain of a feedback amplifier and find the following. a. Gain Margin b. Phase Margin Is the amplifier stable? c. Bode Diagram 20 -20 -40 -60 -80 -180 -270 -1 10 10° 10' Frequency (rad/s) (gp) apnyubew (6op) aseud
What is the effect of the resistance connected in series with the capacitor on the feedback?
Fuels True the feedback path in closed loop system representation by r(t) The numerator polynomial of the transfer function G(s) represented in matlab as the coefficients of increasing powers of s in the numerator of G(s) The name of the Simulink block for plots one signal against another is a scope If finite number of blocks are connected in series or cascade.configuration, then the blocks combined algebraically By addition Can we simulate transient states in Simulink The output in the scope is an analog signal By equating the denominator of transfer function to zero, will be obtained Poles
I have the following circuit, please help me to identify the feedback topology of the circuit usechatgpt init success
Define and differentiate the following terms. Also Draw plots where required. You can use different symbols to denote each term a. Gain Cross over Frequency VS.Phase Cross over Frequency b. Phase Margin VS. Gain Margin c. Three Conditions of Stability in terms of phase cross-over frequency and gain-cross over frequency. Three Conditions of Stability in terms of phase margins and gain margins
Determine the transfer function using Mason’s Rule: (note: -H3(s) and -H2(s) for feedbacks)
The output of the op-amp comparator is a --------. a. rectangular waveform b. sinusoidal waveform c. sawtooth waveform
2- For the circuit given below : Vin is a sine wave Vinpp=9 V and Vref=1.2 V , Assume Vsat=+12V Name the circuit and draw the input and output waveforms. Vo Vin Vref 3- Explain why open-loop op-amp configurations are not used in linear applications? Draw the block diagram of opamp and define the function of each block