1 The ISO standard for HDLC procedures (ISO 4335) includes the following defini- tions: (1) An REJ condition is considered cleared upon the receipt of an incoming I-frame with an N(S) equal to the N(R) of the outgoing REJ frame; and (2) a SREJ condition is considered cleared upon the receipt of an 1-frame with an N(S) equal to the N(R) of the SREJ frame. The standard includes rules concerning the relationship between REJ and SREJ frames. These rules indicate what is allowable (in terms of transmitting REJ and SREJ frames) if an REJ condition has not yet been cleared and what is allowable if an SREJ condition has not yet been cleared. Deduce the rules and justify your answer.

1 The ISO standard for HDLC procedures (ISO 4335) includes the following defini- tions: (1) An REJ condition is considered cleared upon the receipt of an incoming I-frame with an N(S) equal to the N(R) of the outgoing REJ frame; and (2) a SREJ condition is considered cleared upon the receipt of an 1-frame with an N(S) equal to the N(R) of the SREJ frame. The standard includes rules concerning the relationship between REJ and SREJ frames. These rules indicate what is allowable (in terms of transmitting REJ and SREJ frames) if an REJ condition has not yet been cleared and what is allowable if an SREJ condition has not yet been cleared. Deduce the rules and justify your answer.

Systems Architecture

7th Edition

ISBN:9781305080195

Author:Stephen D. Burd

Publisher:Stephen D. Burd

Chapter8: Data And Network Communication Technology

Section: Chapter Questions

Problem 4VE

See similar textbooks

Similar questions

Consider a full-duplex 256 Kbps satellite link with a 240 millisecond end-to-end delay. The data frames carry a useful payload of size 12,000 bits. Assume that both ACK and data frames have 320 bits of header information, and that ACK frames carry no data. What is the effective data throughput When using Stop and Wait?
If transmission time is 5ms and propagation delay is 12ms then draw the complete ‘Stop-and-Wait Flow Control’ with both flow of frame and acknowledgment. Do the similar job for transmission time of 12ms and propagation delay of 5ms.
Computer Science A station, transmitting over a medium, employs exponential back-off. The parameters that govern the exponential back-off are CWE = 32, CWmin = 31 and CWmax = 1023. When CW > CWmax, retransmission is aborted. Assuming the slot time is 20 ns and the frame is sent after retransmission of the first frame, determine the maximum delay due to the error recovery time.
The timer of a system using the Stop-and-Wait ARQ Protocol has a time-out of 6ms and round trip time RTT is 4ms. Assume the acknowledgment of first frame is delayed by 4ms and the third frame is received in error one time. All other frames and acknowledgement are received correctly .Draw the flow diagram for four frames
Data Communication & Computer Network Suppose that Jon's and Jenny's computers are connected by an 8 Kbps link (note, 1 Kbps = 103 bps) that uses circuit switching and that Jon sent some number of bits to Jenny over the link. Suppose that circuit switching on the link connecting Jon’s and Jenny’s computers is implemented using Time Division Multiplexing (TDM), that a frame is 1 sec in duration, and that a frame consists of 16 slots. Jon is assigned one slot in every frame. Considering that it took 12 minutes for Jon to send all bits to Jenny, find how many bits were sent by Jon to Jenny.
Assume M = 1 1 0 1 02 and P = 1 1 02. Compute: a. The frame check sum (FCS).b. The transmitted frame.c. The received frame and check if there is any error in the data.
Question 1 The timer of a system using the Stop-and-Wait ARQ Protocol has a time-out of 6ms and round trip time RTT is 4ms. Assume the acknowledgment of first frame is delayed by 4ms and the third frame is received in error one time. All other frames and acknowledgement are received correctly. Draw the flow diagram for four frames.
Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem3. Consider a digital multimedia transmission system. Separate audio and video coders are used to encode these signals. Audio and video bits are packed in packets together and transmitted over a transmission link. Each packet is 2,000 bytes long, which includes a 48-byte header. The system generates one packet every 40 ms. Calculate the following values:a. The minimum data transmission rate required to support the above system.b. The minimum signal-to-noise ratio (SNR) in dB required to transmit the above audio and video information. Assume a 400-kHz transmission channel bandwidth is used.c. The end-to-end packet delay over a 50-km link, using answer in Part a).
1. identify which layer or layers of the OSl model do the following: a. Error correction and retransmissionb. Responsibility for carrying frames between adjacent nodesc. Provides independence from differences in data representationd. Format and code conversion services 2. Given two sine waves X and Y, if the frequency of X is four times that of Y, then the period of Y is ____ that of X
Q3.Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem in your submission. Consider a digital multimedia transmission system. Separate audio and video coders are used to encode these signals. Audio and video bits are packed in packets together and transmitted over atransmission link. Each packet is 2,000 bytes long, which includes a 48-byte header. The system generates one packet every 40 ms. Calculate the following values:a. The minimum data transmission rate required to support the above system.b. The minimum signal-to-noise ratio (SNR) in dB required to transmit the above audio and video information. Assume a 400-kHz transmission channel bandwidth is used.c. The end-to-end packet delay over a 50-km link, using answer in Part a).
Draw suitable diagrams for frame relay format and address field format, explain the followings with its tasks in frame relay address. CIR b) DLCI c) DE d) EIR
4. The design issue of Datalink Layer in OSI Reference Model is a. Framing b. Representation of bits c. Synchronization of bits d. Connection control