1. 2. Amplitude 3.5 3 2.5 2 1.5 1 0.5 (a) 0.4 (b) 0.5 (c) 0.6 (d) 0.7 0.5 1 (a) 3.14 (b) 6.28 (c) 1.57 (d) 1.00 Step Response 1.5 Time (seconds) 2 What is the damping ratio, , associated with the unit step response for the pure, two-pole system? (Please allow for rounding error.) 2.5 3 Find the damped frequency of oscillation, wa, for the pure, two-pole system. (Please allow for rounding error.)

1. 2. Amplitude 3.5 3 2.5 2 1.5 1 0.5 (a) 0.4 (b) 0.5 (c) 0.6 (d) 0.7 0.5 1 (a) 3.14 (b) 6.28 (c) 1.57 (d) 1.00 Step Response 1.5 Time (seconds) 2 What is the damping ratio, , associated with the unit step response for the pure, two-pole system? (Please allow for rounding error.) 2.5 3 Find the damped frequency of oscillation, wa, for the pure, two-pole system. (Please allow for rounding error.)

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.22P

See similar textbooks

Similar questions

Suppose an electrical signal generated, y(t) can be modelled as follows where t, is time in second, y(t) is voltage in mv. a) Produce graphs showing the amplitude and phase spectrum of y(t). b) State whether this time-domain signal y(t) is periodical, or non-periodical and justify your answer.
A forced excited m–k–c system is under a harmonic force F: F=5000sinωt If the mass m = 50 kg; k=80E3 N/m; damping ratio=0.3 and dynamic deflection is to be less than 0.08 m. Determine the range of operating excitation frequency. Also the show the operating range of frequency on a graph.
Example 1 A mass of 1 kg is to be supported on a spring having a stiffness of 9800 N/m. The damping coefficient is 5.9 N-sec/m. Determine the natural frequency of the system. Find also the logarithmic decrement and the amplitude after three cycles if the initial displacement is 0.003m.
Consider two systems one is second order and the other is third order. The characteristic equations are: as2+bs+c for the second order and as3+bs2+cs+d for the third order, where a,b,c,d are positive real numbers. Then which of the following is correct with regard to the stability of these two systems? a. stability of either system cannot be confirmed with the given data b. third order is definitely stable but second order cannot be confirmed c. both systems are definitely stable d. second order is definitely stable but third order cannot be confirmed
Find f(t) for each of the following functions. 1. F(s)=320s2(s+8). 2. F(s)=80(s+3)s(s+2)2. 3. F(s)=60(s+5)(s+1)2(s2+6s+25). 4. F(s)=25(s+4)2s2(s+5)2.
Consider the following linear time-invariant discrete-time system which is casual. Y[n]=y[n-1]-0.21y[n-2]+3x[n]+2x[n-2] Find the system function H(z). Draw its pole zero plot with the region of convergence.
Calculate the range of values K will take for the steady-state error to be ??? ≤ 0.04 when the input of the system is ?(?) = ?. Calculate the range of values K will take for the damping ratio to be 1>ξ ≥(1/2√6). Calculate the damping rate ξ and the undamped natural frequency ?? so that ? = 0.5
: If F(s) = s 4+ 5s3+20s 2 + 40s + 50 , Investigate the stability of this system
The system whose characteristic equation is given as s3 + 2s2 + Ks + 20 = 0 is asymptotically stable for which K values
Enter the value of the K coefficient required for the marginally stable/unstable system of a system whose characteristic equation is given as s3+6s2+3s+K=0.
Find the solution to the difference equation given below?[?] − 0.25?[? − 2] = ?[?]when the unit-step function ?[?] = ?[?] is applied to this system assuming the initial conditions of ?[−1] = 1 and?[−2] = 0.
The equation in Excel should be of the form: , where A and b are constants. In this case, x is the independent variable representing time, and y is your current measurements. A represents the initial value of the current from , and b represents the reciprocal of the time constant, RC. This means that b = 1/RC. Since RC = (100,000 Ω)(100x10-6 F) = 10 s, therefore the reciprocal should be: b = 0.1. It is this value that want to use to verify the theoretical equation in the Background. Please answer questions in image.