1. A 50-kg box has an initial speed of 7 m/s along the floor. The coefficient of kinetic friction is 0.40. Calculate the time required for the box to stop and the maximum distance x covered by the box. Vo = 7 m/s 50 kg Mk = 0.40

1. A 50-kg box has an initial speed of 7 m/s along the floor. The coefficient of kinetic friction is 0.40. Calculate the time required for the box to stop and the maximum distance x covered by the box. Vo = 7 m/s 50 kg Mk = 0.40

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.79P: The coefficient of rolling resistance between the 30-kg lawn roller and the ground is r=0.1. (a)...

See similar textbooks

Related questions

Q: 3. A pulley of moment of inertia 2.0 kgm² is mounted on a wall as shown in the following figure.…

Q: What is the efficiency of the Diesel engine if the heat added during the constant pressure…

A: Given :heat added during the constant pressure combustion heat rejected To find: efficiency of the…

Q: The fluid at rest in a storage tank is released by opening the valve at the bottom. The fluid then…

A: Given:To find:(a) particle's maximum acceleration at the given point.(b) Is the flow steady or not.

Q: E/A K 12 B 5KN لے * Solve for reactions and draw moment diagram using method of consistent…

Q: Problem 4 For the beam and loading shown, (a) draw the shear and bending moment diagrams, (b)…

A: For the beam and loading shown,(a) draw the shear and bending moment diagrams,(b) determine the…

Q: Two 5-kg uniform bars are connected to form the linkage shown. Neglecting the effect of friction,…

A: The mass of rods are

Q: The disk starts at wo = 4 rad/s when 0 = 0, and is given an angular acceleration a = (0.30) rad/s²,…

Q: nout slipping under ing constant k, is un G after the center

A: The number of revolutions is obtained as follows-

Q: B с 34 35 K L 30 34 Z 18 20 a) What is the cycle time of one finished chair? b) What is the possible…

A: This question is from topic of resource allocation and management in operations research. Here the…

Q: summarize journals/papers related to stratified flow, or provide the titles of related journals,…

Q: 8.7 Diffuser A jet flies at an altitude of 10 km, where the pressure is 0.32 bar, and the…

A: To Find:The mass flows into the engine.The pressure increase across the diffuser.Given:The altitude…

Q: A1. Produce a Mohr's circle for the stress state of a 2D plane stress element at position C (located…

Q: Enumerate the possible steps involved in the design procedure of ventilation systems.

A: The design of ventilation system involve many steps which are enumerated (listed) below

Q: Problem 1: Recall the two-mass system from a previous problem set, in which you deter- mined the…

A: To Find:the function of the potential energy.the Taylor expansion series.The total kinetic energy…

Q: A cast iron flywheel is rotated at a speed of 1200 rpm and having a mean rim radius of 1 foot. If…

Q: Which moment has a greater magnitude? 10 m F 70° A B 7 kN A. The moment of the force F about A The…

A: Which moment has a greater magnitude?A. The moment of the force F about A.B. The moment of the force…

Q: A man having a weight of 195 lb attempts to hold himself using one of the two methods shown in…

A: Since you have posted a question with multiple sub parts, we will provide the solution only to the…

Q: 1. A truck has a weight of 7500 lbs and rest of 4 tires, each having a surface area contact with the…

Q: WHEN SEAWATER FLOWS INTO THE BOTTOM OPENING AT 10 M/S, CALCULATE THE VELOCITY OF THE SEAWATER LEVEL…

A: The objective of this question is to calculate the velocity of the seawater level inside the ballast…

Q: A thermocouple is used to measure the temperature of hot gas flowing in a duct having a wall…

A: Here we will apply the energy balance theory

Q: What is the ang. velocity and acceleration of the disk when it rolls down the slope freely? Collar A…

A: Collar-A:Write expression for velocity of collar A in vector form.Here is magnitude of slider-A…

Q: Air is exhausted from the fixed jet engine at 20 kg/s with a velocity of 420 m/s while it is being…

Q: 1. If you eat 750 calories of food and then run up several steps of stairs to work off the energy…

Q: An 12 lb weight stretches a spring .32 ft. The weight is initially displaced 0.5 feet above…

A: weight, deflection damping coefficient, Initial condition

Q: An air-conditioning system operates at a total pressure of 1 atm and consists of a heating section…

A: The inlet temperature of air is The inlet relative humidity is .The flow rate is .The temperature of…

Q: 1 kg of steam in a piston / cylinder assembly is initially at 357.933 \ deg C and 2685.66 kPa. It is…

A: Since here we are dealing with steam so despite being a constant temperature process we have to…

Q: Determine the temperature distribution in a spherical layer of a body whose inner surface of radius…

Q: 2. The velocity of a particle traveling along a straight line is v = (3t² – 6t) ft/s, where is in…

A: Given data:- The equation of velocity of the particle is…

Q: 4. For the beam shown below, determine the slope and deflection at points "B" and "C". Assume E =…

A: The modulus of elasticity is .The moment of inertia is .

Q: m - We have two toy rail cars. Car 1 of mass 2 kg is traveling at 3 towards the second rail car of…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Required information Problem 08.041-Determine the principal stresses for the circular cross section…

Q: assume spess What is the indentation diagonal length when a load of 0.60 kg produces a Vickers HV of…

Q: 6-30. The steel plate is 0.3 m thick and has a density of 7850 kg/m³. Determine the location of its…

A: To Find:the location of its center of gravity.the reactions at the pin and roller support.Giventhe…

Q: Draw the complete shear and bending moment diagram for the beam show. pin 4 kN•m 3m 8 kN 1.5 m 4…

Q: At the instant shown, the shaft and plate rotates with an angular velocity of 19 rad/s and angular…

A: The angular velocity is .The angular acceleration is .

Q: Q1. A ball moves along a straight line, starting from the origin. It has an acceleration of a = = (t…

Q: For the circuit shown, give the sequence of operation of cylinders 1 and 2 when the pump is turned…

A: A hydraulic circuit is a device that moves liquid via a network of separate components. This…

Q: The velocity of water is 1.2 m/s. The minor losses due to these bends are equivalent to a pressure…

A: Velocity of water V = 1.2 m/s

Q: Fig. P6.45 and P6.46 36 kips 36 kips Answer FDF = 60.0 kips C; FDG = 15.00 kips C. E 4 panels at 10…

A: Determine the force in members DF and DG of the truss shown.

Q: The 3.22-1b particle A slides on the smooth horizontal plane and is connected to the spring by a…

Q: 8-119 A constant-volume tank contains 30 kg of nitrogen at 900 K, and a constant-pressure device…

Q: A closed glass tube (hydrometer) of length Lond diometer D float in a tank filled with a ligud of…

Q: A cubical furnace 0.5m x 0.5m x 0.5m on the inside is constructed of fire brick(k = 1.04W/mK) with…

Q: *6-80. The polar moment of inertia for the area is Jc = 642 (106) mm4, about the z' axis passing…

Q: Question 2 There is a 20 kg block on an inclined plane that is attached to a rope. The contact…

Q: Q1: The velocity distribution for laminar flow between parallel plates is given by 2 U Umax = 1 2y h…

Q: For the section to the right, find the neutral axis due to the applied moment. (a) First work the…

Q: A mass attached to a spring, set in a container of molasses (a thick liquid) acts like a damped…

Q: lease show your complete solution. Thank you! A fluid of 700 kPa with a specific volume of 0.025m^3…

A: Determine the change in internal energy.

Q: 600 N 900 N ↑ zm 2m ↓ E A 2m- → B

A: Using the method of Joints. Solve for the force in each frame member.

Concept explainers

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.

Question

pleae answer this question

1. A 50-kg box has an initial speed of 7 m/s along the floor. The coefficient of kinetic friction is
0.40.
Calculate the time required for the box to stop and the maximum distance x covered by the
box.
Vo = 7 m/s
50 kg
Mk = 0.40

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Determine the given variable

VIEW

Step 2: Draw the free-body diagram of the box

VIEW

Step 3: Calculate the maximum distance x covered by the box

VIEW

Step 4: Calculate the time required for the box to stop

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 100kg crate is originally at rest and is subjected to two forces. Determine the distance(m) it slides to reach a speed of 18. The coefficient of kinetic friction between the crate and the surface is uk=0.3.
1. A truck is weighing 1.4 KN moves up a slope of 15 °. What is the force generated by the engine if the truck is accelerating at a rate of 3 m/s2? Assume the coefficient of friction is μ =0.1.
A crate has a mass of 120kg and the coefficient of static and kinetic friction is 0.60 and 0.50, respectively. The crate starts from rest and the motor exerts a tension T= 1220 + 200t (N). If the elevation of the dock is 30 degrees from the horizontal, What is the velocity of the crate after 1sec? Compute the power transmitted after 1sec. Provide FBD. Thank you.
A car is moving at speed of 80 km/h. If the coefficient of kinetic friction between the tires and the road is 0.80, determine how long the car takes to stop when it slams on the brakes.
A crate has a mass of 120kg and the coefficient of static and kinetic friction is 0.60 and 0.50, respectively. The crate starts from rest and the motor exerts a tension T= 1220 + 200t (N). If the elevation of the dock is 30 degrees from the horizontal, a. What is the velocity of the crate after 1sec? b. Compute the power transmitted after 1sec. Pls show diagram
The lower block of mass m2 = 3.2 kg is pulled on by a rope with a tension force of 28 N. The upper block has mass m1 = 1.8 kg. The coefficient of kinetic friction between the lower block and the surface is 0.32. The coefficient of kinetic friction between the lower block and the upper block is also 0.32. What is the acceleration of the 3.2 kg block?
The coefficient of friction between the load and the flat-bed trailer show are us = 0.3 and uk=0.2. The initial speed of the truck is 60 km/h. Determine the shortest distance in which the truck can be brought to a stop if the load should not move relative to the truck.
Small objects are delivered to the 78-in. inclined chute by a conveyor belt A which moves at a speed v1 = 1.7 ft/sec. If the conveyor belt B has a speed v2 = 8.6 ft/sec and the objects are delivered to this belt with no slipping, calculate the coefficient of friction μk between the objects and the chute. angle is 29 deg
WORK ENERGY AND POWER COMPLETE SOLUTION A 2kg block hits the spring with a speed of 4 m/s. Determine the total distance traveled by the block before it comes to stop if the spring constant is 8 N/m, and the coefficient of static and kinetic friction is 0.50 and 0.45, respectively.
In 50 seconds, a 3.2-ton vehicle can reach 140 mph from rest. Exclude friction losses while calculating the engine's output.
A block of weight 800N rests on a rough horizontal surface of coefficient of friction 0.2. It is pulled by a force of 1000N applied at an angle of 300 to the horizontal. Determine the velocity attained by the block after it has moved 30 m starting from rest. Proceed to calculate the further distance moved by the body if the pull is removed.
A crate has a mass of 120kg and the coefficient of static and kinetic frictionis 0.60 and 0.50, respectively. The crate starts from rest and the motor exerts a tensionT= 1220 + 200t (N). If the elevation of the dock is 30 degrees from the horizontal,A. What is the velocity of the crate after 1sec? B. Compute the power transmitted after 1sec. Topic: Impulse and momentum