1. A connecting rod supported by a knife-edge at point A. For smalloscillations the angular acceleration of the connecting rod is governedby the relation a = -60 where a is expressed in rad/s2 and 0 in radians.Knowing that the connecting rod is released from rest when 0 = 22.4°,determinea. the maximum angular velocity,b. the angular position when t = 2. 24 s.В

Answered: Image /qna-images/answer/a54c07f9-5fd6-4ba9-b0e5-681377ee3e7d.jpg

1. A connecting rod supported by a knife-edge at point A. For small oscillations the angular acceleration of the connecting rod is governed by the relation a = -60 where a is expressed in rad/s² and 0 in radians. Knowing that the connecting rod is released from rest when 0 = 22.4°, determine a. the maximum angular velocity, b. the angular position when t = 2. 24 s. В

1. A connecting rod supported by a knife-edge at point A. For small oscillations the angular acceleration of the connecting rod is governed by the relation a = -60 where a is expressed in rad/s² and 0 in radians. Knowing that the connecting rod is released from rest when 0 = 22.4°, determine a. the maximum angular velocity, b. the angular position when t = 2. 24 s. В

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the largest value of couple moment M just before the disk begins to slip.
If the e = 45°, and the bar 0Q is rotating in the counterclockwise direction at 1.6 rad/s, which of the following is the velocity of the slider P?.
Rod AB is rotating with an angular velocity of 20 rad/s. Determine the angular velocity of rod BC and the velocity of point C.
For the simply supported beam carrying the concentrated load P = 176 N at its midspan, determine the magnitude of the maximum displacement (in mm) if d = 2.34 m, E = 11.24 GPa , and I =1749035mm4.
l=160mm, b=60mm. AB rotating with constant angular velocity 1600 rpm clockwise. determine the velocity of P. θ = 45°
The collar has velocity of 500 mm/s downward and the speed of the collar is decreasing at a rate of 150 mm/s2. The angular velocity of the bar is 3.20 rad/s CCW and the velocity of point B is 0.400 to the right. (1) Find the angular acceleration of bar AB, (2) Find the acceleration of point B on bar AB.
Should the moment at ED be 256.95? and i am not seeing you calculate that moment at E
The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, θ = 32°, θ˙ = 47 deg/s, and θ¨ = 21 deg/s2. Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.3-kg slider B. Neglect all friction, and let L = 0.64 m. The motion occurs in a vertical plane.
If point B settles by 2mm, determine the reaction of the beam shown. Assume EI is constant withE=200GPa and I =400x106mm4. (Use either Three Moment Equation or Slope Deflection Method)
Data are as follows: P=6.2 kN, L=3.2m, d=1.25m, b=80mm, t=25, h=120mm, h1=90mm. Determine the moment of inertia about the centroidal x-axis in mm^4.
The flexible band F is attached at E to the rotating sector and leads over the guide pulley. Determine the angular accelerations of AD and BD for the position shown if the band has a constant velocity of 4 m/s. Use the Relative Motion Analysis method.
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 150 L/s, and leaves the sprinkler nozzles as 2cm diameter jets at an angle of u from the tangential direction. The length of each sprinkler arm is 0.52 m. Disregarding any frictional effects, determine (a) Angular momentum and (b) the rate of rotation n of the sprinkler in rev/min For ϴ = 60°.