1. A member is formed by connecting a steel bar to an aluminum bar is shown. Assuming that the bars are prevented from buckling sideways. Calculate the magnitude of force P, that will cause the total length of the member to decrease by .30 mm. E for steel is 2x105 N/mm² and for aluminum 6.5x104 N/mm². 20 cm 30 cm 6 cm x 6 cm Steel bar 10 cm x 10 cm Aluminium bar

1. A member is formed by connecting a steel bar to an aluminum bar is shown. Assuming that the bars are prevented from buckling sideways. Calculate the magnitude of force P, that will cause the total length of the member to decrease by .30 mm. E for steel is 2x105 N/mm² and for aluminum 6.5x104 N/mm². 20 cm 30 cm 6 cm x 6 cm Steel bar 10 cm x 10 cm Aluminium bar

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 42378-Nload, using the following data: length of steel = 1.28 m, length of bronze =2.5 m Area of steel = 570 mm, Area of bronze = 338 mm Modulus of elasticity of steel = 196 Gpa, Modulus of elasticity of bronze = 75 Gpa x =0.51 m, y = 1.16 m, and z = 0.76 m.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the bronze rod caused by the 37040-Nload, using the following data: length of steel = 1.36 m, length of bronze = 2.16 m Area of steel = 592 mm, Area of bronze = 350 mm Modulus of elasticity of steel = 183 Gpa, Modulus of elasticity of bronze = 80 Gpa x = 0.59 m, y = 1.16 m, and z = 0.74 m. Round off the final answer to two decimal places.
The figure shows a rigid bar that is supported by a pin at A and two rods, one made of steel and the other of bronze. Neglecting the weight of the bar, compute the force (in N) in the steel rod caused by the 40209-Nload, using the following data: length of steel = 1.23 m, length of bronze = 2.4 m Area of steel = 510 mm, Area of bronze = 268 mm Modulus of elasticity of steel = 214 Gpa, Modulus of elasticity of bronze = 84 Gpa x = 0.6 m, y = 1.1 m, and z = 0.9 m. Round off the final answer to three decimal places.
A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a) What is the maximum magnitude of shear force and bending moment, neglecting the sign? Maximum magnitude of shear force, positive value: Maximum magnitude of bending moment, positive value: b) Determine the maximum bending stress and shear stress that occurs in the beam. Maximum bending stress: Maximum shear stress
(strengths of materials) Since the safety stress = 12.5 MPa, calculate the moment M that the section given in the figure can safely carry. Find the equation of the neutral axis.(Iz = 10.67.10^6 mm4; Iy = 45.80.10^6 mm4)
Q.3 A uniform steel plate 360 mm square with a mass of 25 kg is suspended in the horizontal plane by the three vertical wires as shown. Calculate the tension in wire C. (round answer to one decimal places)
Q.2 Three bars each made of different materials are connected together and placed between two walls when the temperature is T1 = 12 oC. Determine the force exerted on the rigid supports when the temperature becomes T2=18 oC. The material properties and crosssectional area of each bar are given in the figure.
15. Compute the resultant of the three forces shown in the figure. A. 894.32 N B. 836.90 N C. None of the Above D. 315.28 N E. 948.27 N
Two forces FA =196 lb and FB =267 lb are acting on the bracket shown with axes x,y,v and w indicated. If the angle measurements on the figure are c=15 , d=7 , f=20and g=6, determine the x-component of FA (lb). Round off only on the final answer expressed in 3 decimal places.
A wooden beam is loaded by a distributed load ww = 6 N/mm as shown in Figure Q4(a). The cross-section of the beam is shown in Figure Q4(b). Assume that LAB = 3000 mm, LBC = 2000 mm, W=190 mm, B0 = 10 mm, and H = 220 mm, h0=40 mm. Units: use N, mm, MPa as consistent units for all calculations. Decimal points: any decimal points are fine a)Determine the 2nd moment of area of this cross-section in Figure Q4(b)? b)Calculate support reactions in A and C, remember the sign of the force. Reaction force at point A: x-direction: XA= y-direction: YA= Reaction force at point C: x-direction: XC= y-direction: YC= c)Calculate the equations of shear force V(x) and bending moment M(x). Type the mathematical expressions or constants. Section AB: Section BC:
The bar shown determines: a) The internal force in section AB, BC and CD. b) The approach or distance between points B and C, and between points C and D. c) The displacement of points A, B, C and D. d) Conceptually, what is the difference between deformation and displacement? Consider: Cross-sectional area of the bar A=50 mm2 , Modulus of elasticity E = 200 x109Pa
A beam has the cross-section shown in the figure. A. What is the distance from top of the flange going to the centroid of the beam, Yg? B. What is the moment of inertia about the z-axis, Iz?