1. A PT100 RTD has a positive temperature coefficient (a) of 0.00392 02/°C. It is being used to monitor the temperature in a room. If the present resistance reading of the RTD is 1150. What is the room temperature? Hint: R = Ro (1+q AT) 2. A differential pressure transmitter's output is a 4-20mA signal. If the input is set to measure liquid level in a tank at 0-15 meters, what is the Liquid level when the transmitter's output is 13mA?

1. A PT100 RTD has a positive temperature coefficient (a) of 0.00392 02/°C. It is being used to monitor the temperature in a room. If the present resistance reading of the RTD is 1150. What is the room temperature? Hint: R = Ro (1+q AT) 2. A differential pressure transmitter's output is a 4-20mA signal. If the input is set to measure liquid level in a tank at 0-15 meters, what is the Liquid level when the transmitter's output is 13mA?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

a. An AM transmitter has the unmodulated carrier power of 20kW and can be modulated to a maximum of 70% before the system saturates/overloads. Find the value to which carrier power can be increased if 40% modulation limit is imposed.b. An analog communication system using FM has the highest modulating frequency of 5 kHz and maximum deviation of 25 kHz. Calculate the bandwidth of modulated signal using Carson’s rule. Compare this value with the one obtained using the simple formula. For practical systems which of these values should be used?
An analog signal of maximum frequency component of 10 kHz is applied at the input of a PCM system with an uniform quantizer having 32 levels. What will be the Transmission bandwidth of the PCM system? Please answer only if you are confident.
Q1-The message signal m(t) into a FM modulator with the parameter kf=25 is shown in the following figure. a) Express the FM signal in time domain.b) Calculate and plot the frequency deviation in Hz.c) Calculate and plot the phase deviation in radians.
Calculate the modulating voltage of an audio signal necessary to provide100% modulation of a 100-V carrier that is simultaneously modulated by 2audio waves with m1 and m2 equal to 75% and 45% respectively.
Given an FM modulator with a deviation sensitivity K1= 3.7 kHz/V and a modulating signal vm = 5.2 sin(2π1,906t), determine the carrier swing in kHz For an FM modulator with an unmodulated carrier amplitude Vc= 14 V, a modulation index m = 1, and a load resistance RL = 8 ohms, determine the power (in watts) in the modulated carrier The percent modulation of the sound portion of a TV signal is 85%. The maximum frequency deviation for the sound portion of the TV signal as specified by the FCC is 25 kHz. Determine the carrier swing (in kHz) of the signal. For an FM modulator with 40-kHz frequency deviation and a modulating-signal frequency fm= 13 kHz, determine the bandwidth (in kHz) using Carson's rule. Given an FM modulator with a deviation sensitivity K1= 1.4 kHz/V and a modulating signal vm = 3.9 sin(2π1,948t), determine the peak frequency deviation in kHz. The percent modulation of the sound portion of a TV signal is 73%. The maximum frequency deviation for the sound portion of the…
What is the period and frequency of this signal? Is the frequency constant?What is the bit rate of a given signal?What is the baud rate of a given signal?
The power of a signal at input to a 200-meter communication cable is 15 milliwatts. The attenuation of the communication medium is -0.5 dB/meter. The output signal of the cable is fed to an amplifier that increases the power of signal by a factor of 1000. a) What is the power of the signal in milliwatts at the output of the amplifier? b) Suppose we measure a total noise power of 60 nanowatts at the output of the amplifier. What is the SNR(dB) for the signal at this point?
Given Kp=50uA/V2, VTP=-1V,VSG=0V, VSD=5V, compute ID?
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: ( i ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC.
For an FM modulator with unmodulated carrier amplitude of Vc = 20cos(2π600Mhz t) and modulating signal of Vm= 8cos(2π10KHz t) a frequency deviation of 15kHz, and a load resistance RL = 10ohms. Determine the total power of the side frequencies A. 14.808W B. 0.1851W C. 0.93W D. 7.404
1. a) Analogue signals, such as audio and video, are digitised for transmission over a digital communication network. i) For a signal of bandwidth B Hz what is the minimum sampling rate at which the signal must be sampled to prevent distortion of the signal? ii) Show, using diagrams of the signal spectrum, why a signal that is not sampled at a sufficiently fast rate will suffer distortion. iii) An audio signal with a bandwidth of 0-20kHz is digitised with a sample resolution of 10 bits. What is the minimum bit rate required to transmit the audio signal? (Assume no data compression).
a) Describe the main sources of errors in a measurement process and state how they may be avoided or reduced. b) List two sources of coherent interference and describe how each may be minimized or eliminated. c) An 8-Bit ADC is used to convert an audio signal ranging over 0 – 12 V. What is the RMS quantization noise associated with full-scale operation of this ADC?