Use 2n = 6.28Computations :1 to 2 decimal placesAnswers (as indicated) in polar form. 1. A series AC circuit consisting ofRare connected across V = 20 VL0°, 100 Hz source. Determine:200 2 and L = 320 mH%3D(a) Inductive Reactance, XL• 75o 75mA L(b) Impedance, Z =(c) Current, I =(d) Voltage drops, VrVL °V =VL °(e) circuit phase angle, 0(f) phase relationship of V and I :The current Ithe applied voltage V by the angle 0.

1) For a series AC circuit consisting of R and L Determine the following : Inductive reactance,…

1. A series AC circuit consisting of R = 200 2 and L = 320 mH are connected across V = 20 VL0°, 100 Hz source. Determine: (a) Inductive Reactance, X. • 75 (b) Impedance, Z = • 75 (c) Current, I mA L (d) Voltage drops, VR VL ° V. VL ° (e) circuit phase angle, 0 (f) phase relationship of V and I : The current I the applied voltage V by the angle 0.

1. A series AC circuit consisting of R = 200 2 and L = 320 mH are connected across V = 20 VL0°, 100 Hz source. Determine: (a) Inductive Reactance, X. • 75 (b) Impedance, Z = • 75 (c) Current, I mA L (d) Voltage drops, VR VL ° V. VL ° (e) circuit phase angle, 0 (f) phase relationship of V and I : The current I the applied voltage V by the angle 0.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

An RLC series circuit connected to a 110 – volt and 50 – cycle AC source, contains the following series resistances and reactances: R1 = 10 ohm, R2 = 15, R3 = 5 ohms, XL1 = 20 ohms, XL2 = 25 ohms, XC = 40 ohms. Find the following: a.) EQUIVALENT REACTANCE b.) TOTAL IMPEDANCE c.) VOLTAGE DROP ACROSS THE CAPACITOR d.) TOTAL INDUCTANCE IN MILLIHENRY e.) TOTAL CURRENT f.) REACTIVE POWER g.) REAL POWER DRAW THE PHASOR DIAGRAM IF POSSIBLE AND ROUND OFF TO FOUR DECIMAL PLACES
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, and admittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. Please show complete solution and draw the circuit diagram. Please round off answers up to the 3rd decimal place.Thank you!
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
An AC series circuit has a load of 100 ohms, 0.5 henry and 10 millifarad and being supplied by a sine wave voltage of 100sin(10t). Calculate the total impedance, total current, voltage drop of the resistor, inductor and capacitor. also the plot phasor of the current and voltages
An impedance (inductive) ZL = (11.5 + j10) ohms is connected in parallel with an impedance (capacitive) ZC = (8 – j20) ohms. Calculate (a) the conductance and susceptance of each branch; (b) the total conductance, susceptance, andadmittance of the circuit; (c) the current in each branch, and the total current and power factor, if the impressed emf is 120 volts. draw the circuit diagram
1) Principle and features of different methods for measuring three-phase power. 2) Discuss the formula of Total Power and Power Factor in a three-phase AC circuit.
Circuit elements with an inductance of 200 mH, a capacity of 50 μF and a resistance of 10 Ω are connected in parallel. If the average value of 198 V sinusoidal AC voltage is applied to this system, find the line current, impedance and phase angle of the circuit. (Take the frequency as 60 Hz.)
Three Impedances each of (6 – j20)Ω are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power and apparent power drawn from supply. phase current (Ip) Answer for part 1 Line current Answer for part 2 real power Answer for part 3 reactive power Answer for part 4 Apparent power Answer for part 5
Understand ac power concepts, their relationships to one another, and how to calcuate them in a circuit For each of the following sets of voltage and current, calculate thereal and reactive power in the line between networks A and B in thecircuit shown. In each case, state whether the power flow is from A to Bor vice versa. Also state whether magnetizing vars are being transferredfrom A to B or vice versa. v=100 cos (ωt−45°) V;i=20 cos (ωt−105°) A.
A 3-phase 60hz wye connected 2000kVA, 2300V alternator gives a short circuit current o 600A for a certain field excitation. With the same excitation, the open circuit voltage was 900V. The resistance between a pair of terminals was 0.12 ohm. Find the full load regulation at a. unity pf b. 0.8 lag pf
The impedance Z1 and Z2 are connected in parallel across 200 V, 50 HZ single phase ac supply. Z1 carries 2 A at 0.8 lag p.f. If the total current is 5 A at 0.985 lagging p.f. Determine - 1.5 1. Value of Z1 and Z2 2. Total power and power consumed by Z2.
Kindly answer letters d, e, f, g A 25 ohm resistor connected in series with a coil of 50 ohm resistance and 150 mH inductance. The combination is connected across the 220 V source. Calculate for the (a) power factor; (b) impedance; (c) true power; (d) graph the impedance triangle; (e) graph the power triangle; (f) show via phasor diagram the behavior of the current and voltage; (g) plot the sine wave equation of the current and voltage.