A Homework 6b 03182022.docx.pdf - Adobe ReaderFileEdit View Window HelpTools Fill & Sign CommentОpen1200%TClick on Tools to convertfiles to PDF.1.A silicon p-n junction has the following parameters:Na = 1017/cm³, Na = 5 x1015/cm³, Diameter of the circularjunction = 10 µm.Calculate Vbi, Xno, Xpo, W, Volume charge in the n-typedepletion (qAxnoNp) and Emax at T=300K.3:28 AMType here to search27°CW24-Mar-22---

Answered: Image /qna-images/answer/6baf272e-60d0-4eed-9195-cc578e259f6b.jpg

1. A silicon p-n junction has the following parameters: Na = 1017/cm³, Na = 5 x10'5/cm³, Diameter of the circular junction = 10 µm. Calculate Vbi, Xno, Xpo, W, Volume charge in the n-type depletion (qAxnoNp) and Emax at T=300K.

1. A silicon p-n junction has the following parameters: Na = 1017/cm³, Na = 5 x10'5/cm³, Diameter of the circular junction = 10 µm. Calculate Vbi, Xno, Xpo, W, Volume charge in the n-type depletion (qAxnoNp) and Emax at T=300K.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A diode has a doping of NA = 14 x 1018 /cm3 on the p-type side and ND = 1015 /cm3 on the n-type side. Calculate the zero-bias junction capacitance per cm2 for the diode. Consider ni = 1010/cm3 and VT = 0.026 V.
A silicon pn junction has the following doping condition: 10^(16)cm³ at n-type side and 10^(17) cm at p-type side.calculate total depletion width W, widths of depletion regions at p and n sides of the junction.where Vbi=0.754v Emax=0.0000165v/m
A diode is doped with NA = 1018/cm3 on the p-type side and ND =1019/cm3 on the n-type side. (a)What is the depletion-layer width wdo? (b) What are the values of xp and xn? (c) What is the value of the built-inpotential of the junction?(d) What is the value of EMAX? Use Eq. E(x) = 1 /εs ∫ ρc(x) dxand as shown.
A silicon pn junction employs NA = 2 × 1016 cm−3 and ND = 4 × 1016 cm−3. Determine the built-in potential at room temperature (T = 300 K).
For the attenuator circuit shown, assume C1 and C2 to be very large (∞) capacitors. Don’t be thrown off by the capacitors (How do they behave at DC? How do they behave at AC if C =∞). Assume D1 and D2 are identical diodes with n=1, V T = 25 mV (use the exponential model). a. Determine the value of the dc voltage, V_N when I = 1mA. b. Draw the small-signal equivalent circuit, replacing the diodes with their small signal resistive model, r_d. c. Determine the value of V_o/V_s when I = 1mA.
Surface barrier diodes have a lower noise figure in high frequencies True False The capacitance of the Varactor diode increases with an increase in reverse bias voltage True False The dark current is a current that will exist with no applied illumination True False The lifetime of LCDs is longer than that of LEDs True False The liquid-crystal display (LCD) has the distinct advantage of having a lower power requirement than the LED (light emitting diodes) True False
SPECS: For the following circuit, both sources are equal, they supply the input voltage Vin, withfunction Vin = 15 sin (ωt) V, a frequency of 60 Hz.These sources connect to a set of diodes that behave ideally as shown. in the figure. Both resistors R1 and R2 are 2.2 kΩ. CURCUIT: The output voltage VA (observe the pin from which it is measured) as a functionmathematical input voltage Vin. Plot the curves of Vin and VA on different graphs.
Electronics circuits Pls show the solution step by step. Thank you. In a bridge-type full-wave rectifier with capacitor filter produces an output voltage with a peak value of 48 V. If the load is 500 Q and the ripple factor is no more than 8%, which of the following capacitors can be used? Support your choice(s)a) 0.68 µF, 50 V b) 680 mF, 25 V c) 62 µF, 75 V d) 560 µF, 75 V
Consider a silicon P- N step junction diode with Nd = 1018 cm-3 and Na = 5 × 1015 cm-3 . Assume T=300K. Calculate the capacitance when it is under reverse biased at 1.5V. Assume a cross sectional area of 1um2. If you want to make the capacitance decrease by factor of 3 what should be the width of the depletion layer?
Since C = 47μF, RL = 1kW and Vs = 90 cos2000t in the given circuit, find the diode current in the one-time filling time range of the capacitanc
In a Si diode, the junction area is 0.25 mm2 and the doping density of the n-type region is ND = 1017 / cm3. ; Additive density of p-type region NA = 1015 /cm3. ni = 1,5 1010 /cm3, q = 1,602 10-19 C, VT = 25mV, r = 12, o = 8,85 10-14 F/cm, μn =1350 cm2/Vs, μp = 480 cm2/Vs, τn = τp = 1 At room temperature, a. Find the densities of minority and majority carriers in both regions b. What is the potential wall height?
True or false a.A p-n junction has a variable capacitance depending on bias. b.n a depletion mode MOSFET the channel is created by implantation of ions not gate bias. c.Diffusion capacitance is zero if the diode length is longer than the diffusion length. d.We can accurately predict the energy and time of an electron. e.. Avalanche breakdown occurs if the potential barrier is narrow, allowing for tunneling of carriers f.For an Schottky contact there is a higher concentration of majority carriers at the interface g.Current can flow between source and drain with a gate bias, VG=0 in an enhancement modeMOSFET. h.To achieve forward active mode in an NPN bipolar junction transistor, the base-emitter voltage must be forward biased and the base-collector voltage must be reverse biased to ensure that electrons from the emitter make it to the collector. i.The Early Effect causes a decrease in IC with increased VC as the depletion region from the collector extends significantly into the base