1. A two phase system has the following parameters: R₁ = 10 resistance, XA = 60 inductive reactance, R = 70 and XB = 12 capacitive reactance. If the phase voltage is equal to 120 volts, calculate a) The individual load currents. b) The power taken by each load. c) The total circuit power. PHASE B 120 V LOAD B 120 70 LOAD A 120 V 0000 PHASE A 100 $60 Ев EA

1. A two phase system has the following parameters: R₁ = 10 resistance, XA = 60 inductive reactance, R = 70 and XB = 12 capacitive reactance. If the phase voltage is equal to 120 volts, calculate a) The individual load currents. b) The power taken by each load. c) The total circuit power. PHASE B 120 V LOAD B 120 70 LOAD A 120 V 0000 PHASE A 100 $60 Ев EA

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.30P: Figure 2.26 shows three loads connected in parallel across a 1000-V(RMS),60Hz single-phase source....

See similar textbooks

Similar questions

A source supplies power to the following three loads connected in parallel: (1) a lighting load drawing 10kW. (2) an induction motor drawing 10kVA at 0.90 power factor lagging, and (3) a synchronous motor operating at 10hp,85 effIciency and 0.95 power factor leading (1hp=0.746kW). Determine the real, reactive, and apparent power delivered by the source. Also, draw the source power triangle.
A 60Hz, single-phase source with V=27730 volts is applied to a circuit element. (a) Determine the instantaneous source voltage. Also determine the phasor and instantaneous currents entering the positive terminal if the circuit element is (b) a 20 resistor. (C) a 10mH inductor, and (d) a capacitor with 25 reactance.
Consider the load convention that is used for the RLC elements shown in Figure 2.2 of the text. A. If one says that an inductor absorbs zero real power and positive reactive power. is it (a) True (b) False B. If one says that a capacitor absorbs zero real power and negative reactive power (or delivers positive reactive power), is it (a) False (b) True C. If one says that a (positive-valued) resistor absorbs (positive) real power and zero reactive power, is it (a) True (b) False
The total kVA rating of capacitors required to raise the full-load power factor of a 3-phase, 440 V, 50 Hz induction motor from 0.75 to 0.85 lagging is Qc = 15 KVAR. Capacitors are delta connected. (i) Determine the line current drawn by the capacitor bank (ii) Determine the phase current of the capacitor bank (iii) Determine the capacitive reactance per phase Xc (iv) What will be the capacitance per phase if the capacitors are delta connected ?
1/3 h p ,120 v , 60 hz split phase 1 ph I m has the following parameters : R main = 4.5 ohm , Ra = 9.5 ohm , xa= 3.5 ohm , Xm=3.7 ohm Find the appropriate value of the starting capacitance? Draw the starting phasor diagram relating V, I, I main, and I aux. Ans : 176 µF
Propose size of the capacitor required to improve the pf of a single phase system to 98%. The system supplies follwoing loads i) Lighting load of 50 kW p.f=1 ii) Induction motor load of 125 kW with a lagging p.f of 0.707 iii) A synchronous condenser of 75 kW at p.f 0.9 iv) Other miscellaneous loads of 25 kw at p.f 0.8 lagging. The voltage of the system is xxx V where xxx is 311
AC electrical circuit is below: (refer picture below) a. Determine the current flowing in the load. b. If it is desired that the system power factor be 0.9. With system frequency = 50 Hz. Determine how large the capacitor is must be installed? Which one is correct? A/B/others answer A. C = 7.7015 mF B. C = 35.243 µF c. Please Draw all the phasor. Please give complete, details, and correct answer. Please do step by step, draw the phasor Please using handwriting (not typing ). THANK YOU, I WILL GIVE MANY THUMBS UP.
A parallel circuit of 25 – ohm resistor, 64 – mH inductor and 80 - μF capacitor connected across a 110 V, 50 Hz, single phase supply is shown in the figure below. Calculate: a.) the current in the individual element, b.) the total current drawn from the supply, c.) overall power factor of the circuit. Draw a neat phasor diagram showing IR, IL and IC.
Task A2 Power factor correction In an AC circuit, the current flowing through Load A is found to be 15<9.20 A. The voltage across the load is 240<620 V. 1) Calculate the apparent, real and reactive power, and the power factor of Load A. 2) A capacitor is connected in parallel with Load A to raise the load power factor to 0.98 lagging. Calculate the capacitance C of the capacitor to achieve the desired power factor. (< is the phase sign)
Calculate the following values using circuit analysis with detailed steps of calculation. Reactance of L1 XL = …………..ΩTotal Impedance ZT = …………..ΩCurrent in circuit I =……………mAFigure 2: RL CircuitVoltage across R1 ER =……………VVoltage across L1 EL =……………VPower dissipated P =……………WQuality Factor Q.F = XL /R =………Phase angle θ =……………Total reactive power in the circuit Q =……………VArApparent power delivered by source S =…………….VA
An industrial load of200KW has a powerfactor of 0.5 lagging. Agroup of synchronousmotors operating at apower factor of 0.8leading is installed andthe over-all power factorimproves to 0.75 lagging.Determine the KVArating of the synchronousmotors installed.Answer = 130.2354 KVA
A non-reactive resistance of 60 Ω is connected in series with a 36 µF capacitor in each phase of a star-connected load.The load is connected to a 260 V, three-phase,50 Hz supply and ABC phase rotation. Use Van as the reference. Calculate the line current,( Ia) in polar form.