1. A voltage transformer has 1500 turns of wire on its primary coil and 500 turns of wire for its secondary coil. What will be the turns ratio (TR) of the transformer? 2. If 240 volts is applied to the primary winding of the same transformer in problem no. 1, what will be the resulting secondary no load voltage? Answer question #2 only, Thankyou

1. A voltage transformer has 1500 turns of wire on its primary coil and 500 turns of wire for its secondary coil. What will be the turns ratio (TR) of the transformer? 2. If 240 volts is applied to the primary winding of the same transformer in problem no. 1, what will be the resulting secondary no load voltage? Answer question #2 only, Thankyou

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter24: Gas And Oil Central Heating Systems

Section: Chapter Questions

Problem 6R: The nameplate on a transformer will indicate whether or not it is a Class 2 transformer. (True)...

See similar textbooks

Similar questions

Using the method shown in this unit, what is the approximate short-circuit current available at the terminals of a 50-kVA single-phase transformer rated 120/240 volts? The transformer impedance is 1%. a. Line-to-line b. Line-to-neutral
An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 V, what is the high-leg voltage?
1. a multimap transformer has the following taps: 0V, 3V, 5V, 10V, if the primary voltage is 100 volts, what is the turns ratio? 2. the transformer has a rated voltage of 200 volts but when loaded, it only gives 180 volts. what is the percent voltage regulation of the transformer? answer in percent ANSWER ASAP THANK U
1. A voltage transformer has 1500 turns of wire on its primary coil and 500 turns of wire for its secondary coil. What will be the turns ratio (TR) of the transformer? 2. If 240 volts is applied to the primary winding of the same transformer in problem no. 1, what will be the resulting secondary no load voltage? 3. Calculate the voltage output by the secondary winding of a transformer if the primary voltage is 35 volts, the secondary winding has 4500 turns, and the primary winding has 355 turns.
A single-phase transformer rated 75 kVA, 8000 volts primary and 240 volts secondary is given the short circuit test. With the secondary terminals short circuited, 440 volts (60 Hz) is impressed on the primary, which then draws rated current and 1125 watts. Solve for the percentage impedance of the transformer. Answer is 5.5%. Show solution ASAP complete
Calculate the number of turns needed in the secondary winding of a transformer to transform a primary voltage of 300 volts down to a secondary voltage of 180 volts, if the primary winding has 1150 turns of wire. ANS. Nsecondary= 690 turns
12. A transformer has a primary voltage rating of 240 V and a secondary voltage rating of 80 V. If the windings were connected subtractive, what voltage would appear across the entire connection? 13. If the windings of the transformer in Question 12 were to be connected additive, what voltage would appear across the entire winding? (Answer #13)
Please only answer b part iii. Thank you. You have been hired as an engineering consultant to diagnose an overheating and low output voltage problem with a three-phase transformer. The service technicians informed you that the transformer has a solid nickel core, insulated aluminum windings and a single phase of the transformer is rated at 50 kVA, 6900/400 V, 60 Hz. The transformer cannot be disconnected for open and short circuit testing and only the input lines and output outlets are accessible for current and voltage measurements. (a) The following measurements were taken after and during working hours when all the electrical devices were off and on,respectively. No load condition: Input Phase Current = 3∠−60°A, Output Voltage = 400∠0°V Load condition: Input Phase Current = 8.45∠−37.35°A, Output Voltage = 370∠−0.64°V Assuming the input voltage is maintained at its rated value, calculate the modelled internal parameters Ro, Xm, Reqand Xeq of the transformer referred to the high…
1-) A phase transformer with equivalent circuit parameters R1 = 1 ohm, R2 '= 1.4 ohm, X1 = 2 ohm, X2' = 1.8 ohm, Xm = 1100 ohm, Rre = 6400 ohm, the idle primary voltage is 220 volts and the secondary voltage is 22 volts. a.) Calculate the actual values of the parameters of the secondary side. b.) Calculate the idle running iron and magnetizing currents and transformer losses in idle operation. c.) The transformer is connected to the network whose voltage does not change and it feeds a load with impedance Zy = 0.5 + j0.3 ohms. In this operating condition, calculate the secondary voltage of the transformer and the active and reactive powers drawn from the secondary side by using the T equivalent circuit. ( please solve them all,thanks..)
Answer the following questions based on the circuit and transformer nameplate shown.
Calculate the number of turns needed in the secondary winding of a transformer to transform a primary voltage of 300 volts down to a secondary voltage of 180 volts, if the primary winding has 1150 turns of wire.
3 single-phase transformers of 2200/220 Volts each will be combined to form a 3-phase transformer. The 3-phase transformer will be fed from a line voltage of 2200 volts and will feed the load with a line voltage of 380 volts. Accordingly, which of the following should be the connection type of this 3-phase transformer? a. star-star b. triangle-star c. Triangle-Triangle D. None e. Star-Triangle