1. An inclined plane as shown in figure 1 is used to raise an object of mass 30 kg. If the plane isinclined 5 above/the horizontal and the coefficient of friction is 0.20, calculate the idealmechanical advantage, actual mechanical advantage, and the efficiency of this machine.2. The pitch of a jackscrew shown in figure 2 is 0.3 cm and has a lever arm of 60 cm length.What force at the end of the lever arm will raise a load of 190 kg if the efficiency of the machineis 12 %?3. The IMA of the pulley system shown in figure 3 is 4, how far must the applied force move ifthe load moves 1 ft? If the load weighs 200 lb and the efficiency of the system is 90 %, whatmust be the applied force?

Given data in question Mass Angle Coefficient of friction To find out Actual and ideal mechanical…

1. An inclined plane as shown in figure 1 is used to raise an object of mass 30 kg. If the plane is inclined 5 above the horizontal and the coefficient of friction is 0.20, calculate the ideal mechanical advantage, actual mechanical advantage, and the efficiency of this machine.

1. An inclined plane as shown in figure 1 is used to raise an object of mass 30 kg. If the plane is inclined 5 above the horizontal and the coefficient of friction is 0.20, calculate the ideal mechanical advantage, actual mechanical advantage, and the efficiency of this machine.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In the figure below, the weight of the block is 300 kg and the angle of internal friction is 24.2 degrees. a. If h = 50 cm and P = 50 kg. does the block move? b. If h = 50 cm, what is the smallest P to start motion?
A 1.50-kg steel ball is dropped from a plane to an ocean. If the velocity of the ball just before reaching the water is 11 m/s and if the resistance in the water is 2.8v, what is the distance travelled by the object after 3.3 seconds? Answer in four decimal places. differential equation
A grindstone in the shape of a solid disk with diameter 0.520 m and a mass of 50.0 kg is rotating at 850 rev/min. You press an axe against the rim with a normal force of 160 N (see Figure below), and the grindstone comes to rest in 7.50 s. 1) What is the moment of inertia of the grindstone? 2) What force is bringing the grindstone to a stop? What is the net torque caused by that force? 3) What is the size of the force? 4) What is the coefficient of friction between the axe and the grindstone?
Calculate the energy required to lift an elevator and its occupants with amass of 2000 kg for the following situations: (a) between the first and thesecond floor, (b) between the third and the fourth floor, (c) between the firstand the fourth floor. (as shown .) The vertical distance between eachfloor is 4.5 m. We can use as shown to analyze this problem; the energy required to lift the elevator is equal to the change in its potential energy, starting with
A mass of 3.9kg is projected with a speed of 4.7m/s up a plane inclined 38 degrees with the horizontal. If coefficient of kinetic friction is 0.27, determine the distance it will travel before it stops. Note: use 3 decimal places
A frame shown in the figure consists of a horizontal rigid bar that is supported by two concrete columns. The temperature of system is increased by ΔT= 90 °C. Assume α1 = 7.5 x10-6/°C, α2 = 13 x10-6/°C, a = 290 mm, and L = 270 mm Determine the angle of rotation if the temperature of system is increased by ΔT? In micro rad
1. Given: X = 100 kg; Y = 150 kg Solve for the acceleration of block X in m/s2 for Case 1. Ignore the friction and mass of pulleys. (3 significant figures)
Civil question - solve this A mass of 400 g shown in given Figure is hooked up to a mild spring whose pressure regular is 5kN/m. it is free to oscillate on a horizontal frictionless track. If the mass is displaced 10cm from equilibrium and launched from relaxation, discover (a) duration of motion,( b) maximum speed of the mass, (c) maximum acceleration of the mass, and (d) equations for displacement, speed and acceleration as function of time..
The figure shown a motor pulling an object in an in clined surface determine the power required to move the object at a constant speed of 3.5m/s. The coefficient of friction between the object and the inclined surface is 0.20.
The coefficient of static friction between a book and a desk surface is 0.6. The book weighs 20 N. If a horizontal force of 10 N is applied to the book, would the book move? And if not, what is the magnitude of the friction force? What should be the magnitude of the horizontal force to set the book in motion?
A mass of 3.0kg is projected with a speed of 5.6m/s up a plane inclined 33 degrees with the horizontal. If coefficient of kinetic friction is 0.21, determine the distance it will travel before it stops.NOTE: use 3 decimal places
A 100-ft long dam holds 30 ft of water as shown in the figure. Using the panel equations, determine the hydrostatic force (in kips) acting on the dam. Determine the moment of inertia of the wetted surface of the dam. Your answer should be in ft^4. Determine the eccentricity in feet. At what distance from the bottom of the dam (along the surface of the dam) is the hydrostatic force acting? Your answer should be in feet.