1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g 9 19mm Gusset Plate 178mm L 178 x 102 x 19

1. An L 178 x 102 x 19 with one line of 20mm diameter bolts in each leg in usual gage as shown. Assume the connection length is 450mm. The pitch distance for the subsequent standard size holes is 75mm. Use ASTM A572M Grade 345 steel materials and : a. Determine the design strength of the member. b. Specify the maximum permitted length of the member as per AISC specifications.) 102mm g 9 19mm Gusset Plate 178mm L 178 x 102 x 19

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.6.5P

See similar textbooks

Similar questions

An L 150 x 100 x 16 is used as a tension member, with one gage line of 20 mm bolts in each leg at the usual gage location (Table3.1, where g=60 mm, g1=55 mm, and g2=60mm). Two rows of bolts are used in the long leg, and one in the short leg. What is the net area of the given steel connection? Stagger, s=58.63mm (Key Answer: An=3,008.00 mm)
Determine the factor of safety with an applied load of 500 kN. The six bolts are in single shear connection, have an ultimate strength of 670 MPa, and a diameter of 32 mm.
The plate shown is attached by using three M12x2 grade 8.8 bolts. Which screw is subjected to the largest stress? What safe load ( static) F can be supported by the screw for n=1.5.
A bracket must support the service loads shown in the figure below. The loads act through the center of gravity of the connection. The connection to the column flange is with eight 7/8-inch diameter, A325N bolts. A992 steel is used for all components. Is the connection adequate? Use LRFD. Show all work to verify the bearing strength and the combined effects from tension and shear in the bolts. Ignore any potential prying action created in the WT.
A C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown in Figure P3.2-3. If Fy = 50 ksi, Fu = 65 ksi, and Ae = 0.90An, compute the following. a. The design strength for LRFD. b. The allowable strength for ASD.
0.1: An MC9x23.9 is connected with 3 /4-inch diameter bolts as shown below. A572 Grade 50 steel is used. Determine the design strength for the section.
A single-angle tension member 175 mm x 100 mm x 18 mm haw two gage lines in its long leg and one in the short leg for 16 mm bolts arranged as shown. Area of the angular section is 4961 mm^2. Use A36 steel Fy = 248 MPa and Fu = 400 MPa. Standard nominal hole diameter for 16 mm bolt = 17 mm. Determine the net area of the angular section. Determine the allowable tension strength of the angular section based on the gross area. Determine the allowable tensile strength of the angular section based on the effective net area. Reduction factor U = 0.75
Compute the net area. The 1 x 10 plate shown in Fig. P3-10.The holes are for 7/8-in Ø bolts.
A C12 × 30 is connected with 1-in. diameter bolts in each flange, as shown. If Fy = 50 ksi, Fu = 65 ksi, and Ae = 0.90An, compute the following. a. The design strength for LRFD. b. The allowable strength for ASD.
Check the block shear capacity of the connection, use lrfd and asd design expression. Given the lightest W section from Plate 3, connected toa PL% x 10 on its top and bottom flanges, available to support working tensile loads of D = 420 kips and W = 330 kips. The member is to be 20 ft long and is assumed to have two lines of holes for 4-in diameter bolts in each flange. There will be at least three holes in each line 3 inches on center.
Using bearing type connection, determine the number of25mm A490 bolts required, by LRFD only. Determine the design tensilestrength Pu and the allowable tensile strength Pa of the connection ifeight 25mm A325x bearing type bolts are used in each flange. Includeblock shear in your calculations. Use A36 steel for connecting members.
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 2. The shear lag coefficient U and the effective area Ae