1. Assume length of the m-tape steel weighs 12.5g/m and has a cross section of 0.022 cm². It measures correctly when supported throughout under a tension of 8.0 kg and at a temperature of 20°C. When used in the field, the tape is only supported at its end, under a pull of 9.0 kg, and at only supported at an average temperature of 28°C. Determine the distance.

1. Assume length of the m-tape steel weighs 12.5g/m and has a cross section of 0.022 cm². It measures correctly when supported throughout under a tension of 8.0 kg and at a temperature of 20°C. When used in the field, the tape is only supported at its end, under a pull of 9.0 kg, and at only supported at an average temperature of 28°C. Determine the distance.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The single rope of a cantilever crane supports a load of 200 kN and passes over two pulleys and then vertically down the axis of the crane to the hoisting apparatus. The section AB of the crane is a hollow rectangle. The outside dimensions are 37.5 cm and 75 cm and the material is 2.5 cm thick all round, and the longer dimension is in the direction AB. Calculate the maximum tensile and compressive stresses set up in the section, and locate the position of the neutral axis. (Cambridge) ANSWER: tensile 155 MN/m2, compressive 147 MN/m2; neutral axis 0.365 m from outside of box-section Please show the solution to get the answer.
The steel shaft shown rotates at 4 Hz with 35 kW taken off at A, 20 kW removed at B, and 55 kW applied at C. Using G = 83 GPa, find the maximum shearing stress and the angle of rotation of gear A relative to gear C. NOTE: SHOW FREE BODY DIAGRAM AND COMPLETE SOLUTON
horizontal load applied to the bar AC causes point A to be displaced to the right by an amount ∆?, determine the normal strain in the wire AB. Originally, ?=45°.
The block slides down an incline. It starts from rest and, after moving 6 ft, strikes a spring (k= 100 lb/in). Determine the maximum deformation of the spring. Coeff fr= 0.20. please use energy-work method.
The steel shaft with two different diameters rotates at 4.2 Hz. The power supplied to gear C is 68 kW, of which 42 kW is removed by gear B. Find the maximum shear stress (in Pa) in the shaft if d = 58.1 mm, h = 60.6 mm, L = 3.9 m, M = 2.1 m, and G = 83.49 Gpa. Round off the final answer to two decimal places
Determine the following A. Depth of compression block "a" B. Strength Reduction C. Ultimate moment capacity
The section of the masonry dam is as shown. The specific weight of water is 9.81 kN/m^3 and that concrete is 23.54 kN/m3. Determine the following: a. The resisting moment
The following beam is supported by three cables AD, BE, and CF. Cables AD and CF are made of steel, and cable BE is made of aluminum. The data is presented in the table. A force P of 125 kN is applied, and the temperature increases by 100°C. Determine: The stress in each cable. Answ: 25.09 MPa, 49.22 MPa. The vertical displacement of the beam. Answ: 1.99E-3 m.
The block has a mass of 5 kg and rests on the smooth plane. Determine the unstretched length of the spring.
The standard length of a tape is 100m having a weight of 1.2kg with the standardtemperature of 20 C and standard pull of 5.5kg. The young modulus of elasticity of thetape is 200GPa, cross sectional area is 2.8mm? and the coefficient of linear expansionis 0.0000116/°C. Determine the normal tension of the tape.
A 1-m-diameter cylindrical mass, M, isconnected to a 2- m-wide rectangulargate as shown in Fig. below. The gate is toopen when the water level, h, dropsbelow 2.5 m. Determine the requiredvalue for M in lbs. Neglect friction at thegate hinge and the pulley.
Replace the loading by an equivalent resultant force and determine the magnitude of the resultant and its position from point A.