1. Below, a Vs (t) of a single-phase AC / AA power converter(AC / AA voltage controller) when loaded with ohmic (R) loadFunctions of is (wt) current drawn from linear voltage sourceand related source are given belowlinear voltage sourceV.) = 311sin(27501)V|i(@t) = 100 sin(@t)A<øt sA ve 37, <øt< 2n|welding currenti, (mt) =i(mt) = 0.A0 s ot s7, ve as øt < 37,z 5 an s 35/2a:Find the effective value of the fundamental wave of the welding current.B; Find the value of the active power drawn from the source.C; Find the value of the total harmonic distortion in the source current.www mmun mD; Find the ohm value of the load R connected to the output of the converter.

Given VS(t)=311sin2π50t is:ωt=100sinωt0π2<ωt<π0<ωt<π2…

1. Below, a Vs (t) of a single-phase AC / AA power converter (AC / AA voltage controller) when loaded with ohmic (R) load Functions of is (wt) current drawn from linear voltage source and related source are given below linear voltage source V,)=311sin(2750r)V| i(t) = 100 sin(@t)A søt sa ve 37/ søts 2n welding current i, (mt) = i(mt) = 0.A Oson s/% ve z s an s 3/½ a:Find the effective value of the fundamental wave of the welding current. B; Find the value of the active power drawn from the source. C; Find the value of the total harmonic distortion in the source current. D; Find the ohm value of the load R connected to the output of the converter. mw m mow w

1. Below, a Vs (t) of a single-phase AC / AA power converter (AC / AA voltage controller) when loaded with ohmic (R) load Functions of is (wt) current drawn from linear voltage source and related source are given below linear voltage source V,)=311sin(2750r)V| i(t) = 100 sin(@t)A søt sa ve 37/ søts 2n welding current i, (mt) = i(mt) = 0.A Oson s/% ve z s an s 3/½ a:Find the effective value of the fundamental wave of the welding current. B; Find the value of the active power drawn from the source. C; Find the value of the total harmonic distortion in the source current. D; Find the ohm value of the load R connected to the output of the converter. mw m mow w

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.29P

See similar textbooks

Similar questions

Consider the microgrid of Figure 3.66. A three-phase transformer, T1, israted at 500 kVA, 220 VY grounded/440 V delta, a transformerwith a reactance of 3.5%.Themicrogridis supplied from anAC bus of a PV generating station.The DC bus rated at 540 V.The distributionlineis 10mileslong and has a series impedance of 0.1 + j1.0 Ω per mile and local load of 100 kVA at 440 V. The microgrid is connected to the local power grid using a three-phase transformer T2, rated at 440 V Y grounded/13.2 kV delta,500 kVA with a reactance of 8%. Compute the per unitimpedance diagram of the microgrid system. Assume the voltage base of 13.2 kV on the local power grid side and kVA base of 500
If the values of real power and reactive power is specified for a bus, then it is called as PV bus. Select one: True False
Explain the concept of FACTS (Flexible Alternating Current Transmission Systems) devices. How do they enhance the control and stability of power systems? Provide examples of FACTS devices and their applications.
Which of the following statement is wrong for single phase AC distribution system? 1the drop is the sum of moments of I cos φ and I sin φ components with distances equal to resistance and reactance respectively. 2the distance of separation between wires is relatively smaller as compared to overhead line. 3the net drop is the difference of the drop in reactance due to the quadrature component and in resistance due to inphase component of current. 4the inphase and quadrature components of current contribute to the voltage drop. 5the resistance component is normally higher than the inductive reactance component.
A 3-phase transmission line is being supported by three-disc insulators. The potentials across top unit (i.e. near to the tower) and middle unit are 8 KV and 11 KV respectively. Calculate: 1) The ratio of capacitance between pin and earth to the self-capacitance of each unit 2) The line voltage 3) String efficiency Subject Power Transmission And Distribution
1. High Voltage DC Transmission Systems (HVDCTS) * Write an Overview of the HVDC technology * Focus on covering Necessity, Technology, Scopes, Limitations and Applications.
An impedance coil is connected in series with a fixed resistor, and a 120-V, 50-cyclesource is then impressed across the combination. If the voltage drops across the coil andthe fixed resistor are 70 and 80 V, respectively, when the circuit current is 1.4 A, calculatethe resistance and inductance of the impedance coil.
The time-domain expressions for three line-to-neutral voltages at the terminals of a Y-connected load are v AN = 169.71 cos (ωt+ 26 ∘ ) V, v BN = 169.71 cos (ωt− 94 ∘ ) V, v CN = 169.71 cos (ωt− 94 ∘ ) V, What are the time-domain expressions for the three line-to-line voltages vAB, vBC, and vCA?
Find the following: the power drawn by the 100ohm variable resistor If the variable resistor is set to 200-ohms, instead of 100-ohms, What is the power drawn by the 200-ohms resistor? total current of the system Is the circuit inductive, capacitive, or neither (resistive)? NOTE: Polar form for Voltage & Current. Rectangular form for Impedance
The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V, 60 Hz transformer: Esc = 87 V, Isc = 21.75 A, Psc = 590 W. Calculate (a) equivalent resistance, reactance and impedance referred to the primary, and (b) voltage regulation at a power factor of 0.866 lagging. Subject: Electrical Apparatus and Devices
Humble Reqest To solve this. subject Power Transmission and Distribution
TOPIC: Transmission Lines, Power Systems, and Powerplants:INSTRUCTIONS:- Answer in this format: Given, Illustration, Required Conversion, Solution, Final Answer.- Step-by-step solution, do not skip even simple calculations to avoid confusion.- If answered in written form, make sure it is readable.PROBLEM:A three-phase, three-wire, 500-V, 60-Hz source supplies a three-phase induction motor, a wye-connected capacitor bank that draws 2 KVAr per phase, and a balanced three-phase heater that draws a total of 10 kW. The induction motor is operating at its rated 75 Hp and has an efficiency and power factor of 90.5 and 89.5 percent, respectively. Determine the system KVA. 78.12 75.98 24.81 83.17