1. Connect the circuit shown in Fig. (6). 2. Measure the values of voltages and currents of each resistor in the circuit and record the values in table 1. Note: specify the direction of the currents and voltges from the voltmeter an ammeter readings. 12 R1 1200 R4 3300 13 A 10V + Loop1 Loop2 R5 1000 R3 2200 R2 1200 Resistance R1=1202 R2=1202 R3=2202 R4=3302 Rs=1002 VR(volt) I(mA) ww.

1. Connect the circuit shown in Fig. (6). 2. Measure the values of voltages and currents of each resistor in the circuit and record the values in table 1. Note: specify the direction of the currents and voltges from the voltmeter an ammeter readings. 12 R1 1200 R4 3300 13 A 10V + Loop1 Loop2 R5 1000 R3 2200 R2 1200 Resistance R1=1202 R2=1202 R3=2202 R4=3302 Rs=1002 VR(volt) I(mA) ww.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In the circuit shown, a 6-Ohm resistor connected in series to a parallel combination of two resistors, one is 30-Ohm and the other is R being unknown. Determine the value of R maximum power transfer. Hint: To maximize power in R, use differentiation
find resistor 2k , current using mesh, nodal and superposition
A voltmeter having sensitivity of 200 ohm/volt reads 119 V on its scale of 219 V when connected across an unknown resistance in series with a multimeter. When the multimeter rads 5mA, calculate the error due to the loading effect of voltmeter. Also calculate the error if the milliammeter reads 800mA and voltmeter reads 40V on its 219 V scale.
A meeting hall in an organization is to be provided with a lighting installation. The hall is 30 m × 20 m × 8 m (high). The mounting height is 5 m and the required level of illumination is 144 lm/m2. Design a lighting system for the hall with the given data. Lumens/watt for 200-W lamp = 12 and Lumens/ watt for 500-W lamp = 16. Utilization coefficient = 0.6 Maintenance factor = 0.75 space/height ratio=1 Using metal filament lamps, estimate the following: Draw the spacing layout of these lamps State the reason if any of these 2 lamps cannot be arranged in the hall with the given specification. What is the significance of ‘room surface maintenance factor’ and ‘utilization factor’ in the lighting design
A friend brought a 960 W electric coffee maker from Europe, designed to work with a 240 V. power supply (a) What should it do to connect the appliance in a 120 V source? (b) What should be the current that the coffee maker consumes from a 120 V line? (c) What is the strength of the coffee maker? (The value of each voltage is a effective value.)
Three resistors R1, R2 and R3 are connected in tee. The resistor R1 is connected in series with the supply voltage V1 while the resistor R2 is connected in series with the voltage V2. If V1 = 30 volts, V2 = 20 volts, R1 = 5 ohms, R2 = 10 ohms, and R3 = 15 ohms, calculate the currrent flowing in each resistor. Use Norton’s theorem.
An office space measures 50ft x 90ft with 16ft high walls. A 1.25 air changes per hours is desired for this space. Find the heat loss (in btuh) when the indoor temperature is 70°F and the outdoor temperature is 36°F. Select one: a. Q = 56,100 btuh b. Q = 44,880 btuh c. Q = 37,736 btuh d. Q = 75,900 btuh e. Q = 64,350 btuh
Q: A wood panel containing 16 solar cells. Calculate the total open circuit voltage and short circuit current coming out of the board and draw the relationship between current and voltages in the following cases 1- If you connect each two cells in series and connect the groups in parallel. 2- If all four cells are connected in parallel and the groups are linked in succession, noting that each cell has the following characteristics: Vos = 0.75V, Isc = 2 mA
i. Analyze the role of ADC and DAC used in a Digital Voltmeter when it is measuring a voltage of 3V with neat sketch of the mentioned. ii. In Al Ahmadi substation, a voltmeter of range (0-300V) and ammeter of range (0-10A) are used to measure a line voltage of 11kV and current of 700A. On a particular day the ammeter shows a reading of 7.5A, then estimate the total line current in the substation. User sample values for winding turns.
There are five electric appliances, viz. electric heater, electric lamp, an electric fan,computer and an exhaust fan are connected in parallel in a household. Ther resistanceelectric appliances are 409,522, 80, 200 and 100 respectively. If ane electriccurrent of 240V is flowing through the circuit then find following 1. Evaluate the electric current through heater 2. Determine electric current through electric lamp 3. Find out total resistance of the circuit 4.calculate electric current through circuit 5.evaluate electric current through electric fan
Find the current in 10 ohms resistor of the circuit shown using nodal analysis.
1) Consider the circuit shown with a battery pack and three similar lightbulbs, with two ammeters included in the circuit, before and after the lightbulbs. How do you expect the readings of the two ammeters to compare? I1 > I2 I1 = I2 I1 < I2