1. Determine the distance x to the center of mass of the homogeneous rod bent into the shape shown. If the rod has a mass per unit length of 1 kg/m, determine the reactions at the fixed support O.

Q: figure below. The raw material used is a 2.5mm Mild Steel Plate and is positioned to the bed with a…

A: CNC is an abbreviation for computer numerical control programming, which is utilised in the…

Q: A 150mm long link swings on a pivot from its vertical position of rest to the right through an angle…

A: Given: Length of link OA=150 mm                        OP=30 mm                     Angle= 60o To…

Q: At a certain point in castor oil the shear stress is 0.216 N/m and the velocity gradient 0.216 s. If…

A: We know that the shear stress in castor oil is 0.216 N/m2 and the velocity gradient is 0.216 s-1 at…

Q: Draw the shear and moment diagrams for the beam

A: Need to draw Shear and moment diagram

Q: 3. Löčaté the centroid (x, y, z) of the wire which is bent in the shape shown. 2 in. 2 in. 4 in

A:

Q: An extruded polymer beam is subjected to a bending moment M. The length of the beam is L = 500 mm.…

A:

Q: 2. Derive the formula for the nonflow work in terms of P1,P2, V1 and V2 only for a process involving…

A:

Q: Two wooden members of uniform cross section are joined by the simple scarf splice shown. Knowing…

A:

Q: How technology has changed our way of living.

A: Technology has impacted the way of living in many ways. In many fields, technology has shaped the…

Q: Consider a multilayered birthday cake sitting on a table. A little kid pushes the upper layer, such…

A:

Q: Pl-3. Determine the largest internal normal force in the bar. F D A 10 kN 5 kN 2 kN 6 kN P1-3

A:

Q: Determine the diameter (in mm) of the largest circular hole that can be punched into a sheet of…

A:

Q: 7. A well-insulated piston cylinder device contains 5L of saturated liquid water at a pressure of…

A:

Q: 2. If the 30-kg crate is subjected to a varying force Fas a function of time, F= (15 ² + 24) N, (t…

A:

Q: Use the formulas for the hydraulic press to find the value. A force of 30 lb is applied to a piston…

A: Given, Diameter of the smaller piston = d1 = 5 in Force at smaller piston = F1 = 30 lb Diameter of…

Q: A plastic beam has a cross section with dimensions of a = 2.3 in., b = 8.1 in., d = 4.6 in., and t =…

A:

Q: Create a flowchart or process diagram for making a particleboard from sugarcane bagasse utilizing a…

A:

Q: If the surrounding surfaces have the same temperature as the gas, what is the total (convection plus…

A: Given                                Area, A = 1 m2 Heat transfer coefficient, h = 30 W/m2K…

Q: 7. A well-insulated piston cylinder device contains 5L of saturated liquid water at a pressure of…

A:

Q: Q/draw the projections

A: According to the details provided in the question, we need to calculate THREE PROJECTION VIEW.

Q: 5.10 Gas turbine exhaust of Ex. 5.1 is employed in a waste heat recovery boiler to raise steam at p=…

A: To find: The kinetic energy of the system at an arbitrary instant in terms of the indicated…

Q: Q6/ A car moving on a rough inclined plane are having the following data: Angle of inclination of…

A:

Q: Which statement about vaporization enthalpy and condensation enthalpy is correct?

A: This question is based on the concept of enthalpy.

Q: Density of liquid is 850 kg/m Determine relative density and weight density of the liquid.

A: We know the density of liquid is 850 kg/m3, thus we need to figure out the liquid's relative density…

Q: An ideal vapor compression cycle requires 2.5 kW to power the compressor. You have found the…

A:

Q: Lecture 6: Balanced Delta Load IBR VeN VRY BR 21.8 IRY 82,V -21.8 IYB VYB.

A: The voltages in the three-stage power framework are delivered by a simultaneous generator . In a…

Q: The man stands 18 m from the wall and throws a ball at it with the speed of 15 m/s as shown in…

A:

Q: Given the Truss as shown below with load P, = X N and P, = 3X N. Using Method of Joints, determine…

A:

Q: A chain with a 0.75 in pitch is designed to run on sprockets having 15 and 50 teeth, respectively.…

A: Given data: n=15N=50p=0.75 inCD=36 in Need to determine the length of chain required in pitches.

Q: The tube shown below is filled with oil. Determine the pressure heads at B and C in meters of water.…

A: Given Data: The specific gravity of oil, 0.85

Q: Draw the projections of the line and find the length of the Top View and true inclination of the…

A:

Q: F00 mm, rough luid in the pipe btained from t what is the % er

A: d=600mme=0.6mmL=2500mQ=450L/sρ=1.25kg/m3v=1.5×10-5m2/s To-Find:- %error

Q: Design a cast iron trunk type piston for a single acting four stroke engine developing 75 kV…

A:

Q: Problems /Casing Design Q1/ Compute the body yield strength for 10.75-in, J-55 casing having a…

A:

Q: XA W (cm'/mole) a) What is volume change of the system when 2 moles of A and 3 moles of B are mixed…

A: From given data table XA=0        ,    VB=10cm3/moleXA=1      ,    VA=12cm3/mole

Q: Completely solve and illustrate the problem. Show what are given, required, illustration, analysis…

A: given; diameter of solid shaft(ds)=4.2in                                       =0.1068mweight of…

Q: n, what is the theoretical belt length required?

A: Given: Sheave large diameter D=13.95 in Sheave smaller diameter d=5.25 in Center distance of sheaves…

Q: What are the advantages and disadvantages of the engine lubrication

A: The lubrication system's job is to provide oil to moving parts in order to minimise friction…

Q: You are trying to assess the performance of a heat sink with fins. It has straight rectangular…

A:

Q: a) at the position of the image when the boom is horizontal.

A: Given Data The weigth of the boom is:m=25 kg K=500 kg To find: The cylinder force. Now draw the…

Q: The 20-kg package has a speed of 1.5 m/s when it is delivered to the smooth ramp. After sliding down…

A:

Q: 4Describe in your own words how an aspirator won

A: An aspirator is simple type ejector jet pump. It's objective to produces vaccum with help of venturi…

Q: g at 5 °C suction temperature and a 40°C condensing temperature has an evaporator load 17.6 KW. If…

A:

Q: The platform scale consists of a combination of third and first class levers so that the load on one…

A: For the given configuration: mass of S = 3 kg mass of L = 120 kg It is required to determine the…

Q: Q#2: the condenser of Geothermal Heat Pump will be cooled by A pipe with dimeter 3 cm buried in a…

A:

Q: A spring subjected to a compressive force of 20kN with a spring constant k = 100 k/m. If the…

A:

Q: 1 -4 -2 and B =-1 4 A =-1 -6 6 -1 4 Find : e.) BB"; f.) A(B + A"); g.) A? – 3A + 61.

A:

Q: For your company you need to mass produce 20-cmx10-cm heat sinks to dissipate heat quickly from an…

A: Given data, Dimension of the base/sink = 0.2 m×0.1 m Convective heat transfer coefficient of the…

Q: X(s) from the following block diagram. F(s) Obtain the transfer function F(s) + X(s) S 5 9 A) s – 6…

A:

Q: If an astronaut and her space suit weigh 250 lb on Earth, what should be the volume of her suit if…

A: Given data Weight of the astronaut = 250 lb = 113.3981 kg   We have to identify the volume that…

Layout

The layout is a way of organizing the elements, products, and raw materials in a design. The layout is the representation of information in a structural, logical, descriptive, coherent form.The layout is a mapping of various equipment arrangements, workstations, machinery, plants, and more. It secures the continuous movement of a product quantity along with the quality.