1. Determine the tension in cables BD and CD and the X, Y, and Z components of reaction at the ball and socket joint at point A. NOTE 1: The shaded half disk is a semi-circle with a radius of 1.5 meters (arrow shown in blue) So, the ball and socket joint at A is 1.5 meters from the straight edge of the semi-circle. NOTE 2: The 30ON force (shown in red) is acting in the Z direction only, 0.5m from the straight edge of the disk as noted on the drawing. NOTE 3: The Y axis of the XYZ axis shown on the diagram is 1m from, and parallel to, the straight edge of the semi-circle. NOTE 4: The disk lies in the XY plane. D 3m 300 N fadius B SpointA is s 1.5M 0.5 m C 1m N

1. Determine the tension in cables BD and CD and the X, Y, and Z components of reaction at the ball and socket joint at point A. NOTE 1: The shaded half disk is a semi-circle with a radius of 1.5 meters (arrow shown in blue) So, the ball and socket joint at A is 1.5 meters from the straight edge of the semi-circle. NOTE 2: The 30ON force (shown in red) is acting in the Z direction only, 0.5m from the straight edge of the disk as noted on the drawing. NOTE 3: The Y axis of the XYZ axis shown on the diagram is 1m from, and parallel to, the straight edge of the semi-circle. NOTE 4: The disk lies in the XY plane. D 3m 300 N fadius B SpointA is s 1.5M 0.5 m C 1m N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

look for: a. Reactions b. Shear and Moment Diagramc. Maximum Momentd. Equations w=022 Kn/m
For the beam presented below:a) What is the degree of indeterminacy; b) Determine the moment reactions at the supports and draw the shear and momentdiagrams. (Solve by expressing the internal moment in terms of vertical reactionsat A and B, EI is constant). c) What would the shear diagram look like if a transverse load P was applied right atthe middle of the beam (Make a sketch of the new shear diagram). W (30kN/m) , L (1.9m)
Draw the normal force, shear force and moment diagram of the structure AB = 2 m, BC = 1 m, CD = DE = 2 m
Determine the reactions and all bar forces for thetruss in Figure P9.34. E = 29,000 ksi and members AB,BC, AD, and DC have A = 3 in.2, and members BD, DE,and CE have A = 1 in.2 for all bars.
Calculate the vertical reaction at support D. Enter your answer in kN to two decimal places.
The pole is subjected to the two forces F1 = 860 N and F2 = 450 N in the direction as shown inFigure 1. On the ground, the pole is supported by two cables CB and ED. (a) Determine the components of reactions at the base of a pole, A assuming it to be aball-and-socket joint.
If the pulley can only carry a resultant force of 8kN acting 45 degrees below the x-axis. Determine the magnitudes of the belt forces, P and Q.
look for and show complete solution: a. Reactions b. Shear and Moment Diagramc. Maximum Momentd. Equations w=022 Kn/m
1. what is the maximum moment in the beam? answer in KN-m 2. what is the maximum shear in the beam? what is the highest shear force at 6m? (kN) 3. what is the shear force at the free end of the beam? 4. what is the highest shear force at 6m? (kN 1Decimal point)
Determine the Horizontal component of the reaction at support A. And what is the magnitude of the tension force at point D?
In influence line for vertical reactions at support A and the moment at point B of the beams are shown. From the influence line of support A, what is the value of Ay when x = 4.20 m due to a unit load?
Determine (a) the absolute maximum values of shear and moment in the beam produced by the wheel loads and (b) the maximum value of moment when the middle wheel is positioned at the center of the beam in Figure P12.43.