1. Explain the relationship of the measured voltage and the tripping time shown in the graph? What is the effect? 2.What is the difference between over current and overload protection? Give example each  Note : attempt both the question or else skip the question

Q: Q2) In the load test, is the iron loss present?

A:

Q: What is the battery balancing? Explain the balancing types.

A: The explanation is as follows.

Q: 1 - Draw a neat circuit diagram of connections for this experiment and insert the readings of the…

A: 1)

Q: Example about PMMC Ammeter.

A: To design PMMC ammeter a shunt resister connected to PMMC , and value of shunt resister depends upon…

Q: Whale and Kanmuro are two islands located in the Chimera archipelago. These two are separated by a…

A:

Q: In static characteristics, is defined as the difference between the true value applied to a…

A: The algebraic difference between the indicated value and the true value of the quantity to be…

Q: At standstill condition, the back emf is of maximum value, so the motor can be safely urned ON…

A:

Q: 4. Plot the overcurrent relay used in the experiment according to the set values (Annendix.

A: The relay current characteristics are given in the table for a Inverse and definite time overcurrent…

Q: For tutorial 1, v1 is between 40 and 20 while v2

A: In this question we will find node voltages ... Note:- Due to bartleby policy, I will answer first…

Q: What percent of the full-load current will be attained after one time constant?

A: Let's consider the load as R-L load because most of the loads are inductive in nature and initially…

Q: Explain the working of the Potential meter float gauge with a neat diagram

A: Draw the Potential meter float gauge: Based on the displacement of the float, the float gauge…

Q: Auto Light Switch

A: Automatic Light Control - Automatic  Lighting Control ideally is to control the lights even when one…

Q: Suppose that your car will not start. To determine whether the battery is faulty, you turn on the…

A: Connect your vehicle's battery to the battery of a friend's car in series so that the automobile…

Q: What is a gluon

A: Hideki Yukawa, the Japanese physicist discovered gluon in the year 1947. Gluon is a subatomic…

Q: 1-Explain the concept of "RELIABILITY OF SERIES AND PARALLEL SYSTEMS

A:

Q: In solar module, minimum value of shunt resistance could be 300 Ohm. Select one: True False

A: In solar module, minimum value of shunt resistance could be 300 Ohm.  Select one: True False

Q: How can you measure the temperature of an object using the Calendar-Griffith's bridge, Explain in…

A: Calendar-Griffith's bridge- It is one type of potentiometer used to calculate the voltage difference…

Q: 5 - What should be done first when a person being electric shocked seen? A) Cut off the electricity…

A: If we seen person being electric shocked then we need to do take some necessary action

Q: Could you answer this question in details and giving examples if possible. Thanks a lot.  - Explain…

A: we need explain Arbitration in CAN BUS.

Q: How open circuit test can be performed and which type of losses can be found using this test

A:

Q: Discuss the operation of a multi-meter

A: Solution :    In the above question they are interested to know the operation of a multimeter.   As…

Q: Printer circuit boards are functionally tested after being filled with semiconductor chips, One…

A:

Q: a) Explain the term “suppressed demand “, and give THREE instances in which suppressed demand occurs…

A: answer a) Supressed demand is the situation where energy services provided are insufficient- due to…

Q: What are the static characteristics of a measurement system? De- scribe them with proper example.

A:

Q: Unit commitment if the spinnind reserve not there in the power system what will happen?

A: Here we need to conclude what will happen if the spinning reserve is not present in the power…

Q: Measured value: Value of a measurand as indicated by an instrument. It should always be followed by…

A: Need to find true false

Q: True or False

A:

Q: questions, thank you. Calculate the following :  1) At what voltage is the switching point? 2)…

A:

Q: 6- Explain what Carson's rule is.

A: In this question we will write about Carson rule....

Q: Are the following statements correct or wrong? Justify your answer. (a) GTO requires very high…

A: Are the following statements correct or wrong? Justify your answer. (a) GTO requires very high…

Q: 8. A larger time delay has been provided with over-voltage protection compared to the under-voltage…

A: Time delays are used to control the flow of power in different parts of the system and by…

Q: The main role of charge controller is to regulate the flow of current to the battery so it will not…

A: Given statement The main role of charge controller is to regulate the flow of current to the battery…

Q: A company is producing a certain type of circuit breaker. The fixed cost is (450 000$), and the…

A: Given data, Fixed cost of CB, FC=$450000 Variable cost, VC=$33/unit Breakeven at 37500 units.

Q: Chassis resistance has an Ohm limit for patient safety, what is the Ohm limit

A: Chassis resistance has an Ohm limit for patient safety.

Q: Drawing the pneumatic and electric circuit diagram Carrying out the pneumatic and electric circuit…

A:

Q: What is the relationship of the current-voltage characteristic and the color of the Red, Yellow,…

A: Energy Band Gap :The lowest energy is required by the electron to release from the valence band to…

Q: b) With sketch of diagram, show the number of resistor and switched would be required to implement…

A:

Q: How many types of glide resistors? With an explanation of the function of each one

A: The Club Car V-Glide is a discrete multi-step potentiometer. There are various configurations of…

Q: 2- How to make the duty cycle approach to 50%? 3. Dacian

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: What should be the k interval for the system to be stable

A:

Q: The formula to calculate the load regulation is

A:

Q: Q1/ Draw the following figure, indicating all the required dimensions as shown down.

A: The figure is as shown :

Q: Explain the important functions of the condenser in a thermal power station.

A: Condenser is a part of regenerative feed heating system. It is also called as condensate recovery…

Q: Derive and discuss mathematical relation for the max value of RRRV. Briefly explain why a percentage…

A: Introduction: The rate of increase in re-striking voltage is abbreviated as R.R.R.V. and is…

Q: How many types of glide resistors? With an explanation of the function of each one

A: To explain the types of glide resistors

Q: ease help me answer with my assignment. What is the difference between the voltage regulation and…

A:

Q: Determine the currents in the various branches

A:

Q: How open circuit test can be performed? Which type of losses can be found using this test? Subjcet…

A: Open circuit test is usually performed on low voltage winding of the transformer keeping the hv…

Q: What is the multiplier for the service demand of electric vehicle charging equipment

A: The electric charging station charges the electric vehicle by converting the AC power to DC. It…

Q: At standstill condition, the back emf is of maximum value, so the motor can be safely turned ON with…

A: Choose the correct option   The given statement is  At standstill, the back emf is of the maximum…