i need the answer quickly ICPC-309 Data Acquisition and TelemetryPractice Session-61. For the sample-and-hold (S/H) circuit shown in Figure 1, determine the largest-value capacitorthat can be used. Consider output impedance for Z, of 10 Q, ON resistance for Q, of 10 Q,acquisition time of 10 us, maximum peak-to-peak input voltage of 10 V, maximum output currentfrom Z, of 10 mA, and charge time of capacitor C as 4.6 s where ç is time constant.Sampling pulseAnaloginputa,PAMoutC,Fig.1 S/H circuit for problem 1

Sample and hold circuits - Sample and hold circuits are most commonly used in applications like A/D…

1. For the sample-and-hold (S/H) circuit shown in Figure 1, determine the largest-value capacitor that can be used. Consider output impedance for Z, of 10 2, ON resistance for Q, of 10 2, acquisition time of 10 us, maximum peak-to-peak input voltage of 10 V, maximum output current from Z, of 10 mA, and charge time of capacitor C, as 4.6 s where ç is time constant. Sampling pulse Analog input a, Z2 PAM out C,

1. For the sample-and-hold (S/H) circuit shown in Figure 1, determine the largest-value capacitor that can be used. Consider output impedance for Z, of 10 2, ON resistance for Q, of 10 2, acquisition time of 10 us, maximum peak-to-peak input voltage of 10 V, maximum output current from Z, of 10 mA, and charge time of capacitor C, as 4.6 s where ç is time constant. Sampling pulse Analog input a, Z2 PAM out C,

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Given the information below. Your task is to write a program that samples an analog signal a0 as illustrated below using the MSP430’sADC12 device. Answer the following questions. A. What is the maximum and minimum input voltage of the input signal a0?B. What is the duration of one period of the input signal a0 in milliseconds?C. Let us assume that we configure the MSP430’s device to sample analog input a0 with the sampling frequency fsample = 2 KHz. How many samples, M, do we have per one period of the input analog signal? Fill in the following table by determining the first 6 samples and the last (Mth) sample. Assume that our sampling is synchronized with the a0 (i.e., the first sample is taken at the very beginning of an a0 period). Assume reference voltages VR+ = 2.5 V and VR- = 0V. Sample Number t [ms] a0 [V] Sample value [decimal] 1 2 3 4 5 6 M = E. If you know that…
a. In AC, how are the capacitors treated? b. In AC, how are DC sources treated? c. What is the amplifier configuration of Figure 4? d. What is the expected phase shift of the sinusoidal input at the output side? e. What is Zi across RG, the gate resistor? f. It is the IC in its smallest form. g. The most commonly used metal as interconnect of the chip to external peipheral. h. How is pin 1 of the chip determined? i. An IC package similar to a DIP but with the pins bent outward. j. Which sensors are packed as IC?
For an efficient communication in PCM system, the number of samples per second must be at most be equal to twice the highest modulating frequency.a. A very important considerationb. No, it must be at least equal to twice the highest modulating frequencyc. 80-50 percent true
For the LC Oscillator shown a. Calculate the minimum amplifier gain needed to sustain oscillation b. is the amplifier an inverting or non inverting? why
Using 741 op amp, design a suitable circuit to generate Binary Phase Shift Keyiing(BFSK) modulator. Design should perform in such a way that the BFSK output should contain a frequency of f1=2kHz when message signal is low and f2 =4kHz when the message signal is high. Take the frequency of message signal as 200Hz. Draw the clear circuit diagram and calculate the values of resistors and capacitors used.
Determine the output voltage of 8-bit successive approximation digitalvoltmeter, if (8V) is the input voltage and (10V) is the reference voltage.
Discuss how non band-limited signals be sampled practically
In a binary PCM system, the output signal-to-quantizing-noise ratio is to be held to a minimum value of 40 dB. Determine the number of required levels, and find the corresponding output signal-to-quantizing-noise ratio.
i. Describe the precaution you would take in selecting the sampling interval ii. How may the original signal recovered from the sampled signal?
1. What are the two ways of generating DSB_SC.2. What are the applications of balanced modulator?3. What are the advantages of suppressing the carrier?4. What are the advantages of balanced modulator?5. What are the advantages of Ring modulator?6. Write the expression for the output voltage of a balanced modulator?
Q1.A) If an 8-bit SAR ADC is used to digitize 8V full scale signal, what will be the digital o/p for an analog i/p of 5.76 V (perform complete analysis)?
Present your complete analysis, solution in the proper sequence, and all needed figures. Show all computations.What change(s), if any, can be introduced into the circuit shown below for a) zero bias? b) depletion- mode bias? c) enhancement- mode bias?