i need the answer quickly تة مر1. In a parallel communication, each bit requires a transmitter and receiver.a) Trueb) False2. What is the cable that carries the information in parallel transmissioncalled?a) Parallel lineb) Data busc) Data lined) Data link3. Which of the following is a false reason for parallel lines not being used forlong distances?a) Cost factorb) Signal Attenuationc) Number of transmission channelsd) Low speed,4. Why higher speed communications in parallel transmission require shorterlength?a) Costb) Resistancec) Inductive and capacitance effectsd) Noise5. Which bit is transmitted first in a serial communication?a) Least significant bitb) Most significantc) All the bits simultaneouslyd) Not in any specific order6. In serial communication, if the time interval to transmit one bit is 10us.What is the time to transmit an'8-bit word?a) 8usb) 80usc) 0.8µsd) 0.008µs

Note :- As per guidelines we are supposed to answer only 3 questions. So I request you to please…

1. In a parallel communication, each bit requires a transmitter and receiver. a) True b) False 2. What is the cable that carries the information in parallel transmission called? a) Parallel line b) Data bus c) Data line d) Data link 3. Which of the following is a false reason for parallel lines not being used for long distances? a) Cost factor b) Signal Attenuation c) Number of transmission channels d) Low speed.

1. In a parallel communication, each bit requires a transmitter and receiver. a) True b) False 2. What is the cable that carries the information in parallel transmission called? a) Parallel line b) Data bus c) Data line d) Data link 3. Which of the following is a false reason for parallel lines not being used for long distances? a) Cost factor b) Signal Attenuation c) Number of transmission channels d) Low speed.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter5: Transmission Lines: Steady-state Operation

Section: Chapter Questions

Problem 5.1MCQ: Representing a transmission line by the two-port network, in terms of ABCD parameters, (a) express...

See similar textbooks

Similar questions

What is the delay of sending a data file a station to a destination station? Suppose that the length of the data file is 1 Mbytes and the bandwidth of the channel is 200 Kbps, and the network link between the sender and receiver is 2000 Km and the speed of the light inside the link is 2x108 m/s? Assume that the delay is composed of only transmission time and propagation time.
Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a direct link of R = 1 Mbps. Suppose the propagation speed over the link is 2.5 x 10^8 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuously as one big message. What is the maximum number of bits that will be in the link at any given time?c. Provide an interpretation of the bandwidth-delay product.d. What is the width (in meters) of bit in the link? Is it longer than a football field?e. Derive a general expression for the width of a bit in terms of the propagation speed s, the bandwidth R, and the length of the link d.
Use a 3-to-8 line decoder to implement the following two switching expressions: a. f = A'BC+AB'C'+AB'C+ABC'+ABC b. g = πM(3,4,5,6,7)
Suppose two hosts A and B, are separated by 10,000 kilometers and are connected by a direct link of R = 1 Gbps. Suppose the propagation speed over the link is 2.5 x 10^8 meters/sec.a. Calculate the "bandwidth-delay product", R.tprop.b. Consider sending a file of 400,000 bits from host A to B. Suppose the file is sent continuously as one big message. What is the maximum number of bits that will be in the link at any giventime?c. What is the width (in meters) of bit in the link?
A. Given a fixed route and fixed link types between two end systems, which of the following delays may vary depending on the level of congestion in the network? Select one: a. processing delay b. propagation delay c. transmission delay d. queueing delay ============================= B. Suppose there is exactly one packet switch between a sending host and a receiving host. The transmission rates between the sending host and the switch and between the switch and the receiving host are R1 and R2, respectively. Assuming that the switch uses store-and-forward packet switching, what is the total end-to-end delay to send a packet of length L? (ignore queuing, propagation, and processing delays) Select one: a. L/(R1+R2) b. (R1+R2)/L c. L/R1+L/R2 d. 2∗(L/R1)
04] The engineers of the telecommunication company tested the link between the sender and the receiver for a multimedia application, and found Q(x)=0.158 for the 16-QAM digital communication system. Can this system transmit data free from ISI problem with 10 kbps speed over a noisy channel of 5 kHz? Prove mathematically.
For transmission over small distances, PAM would be used only as a means of message processing for time-division multiplexing. Select one: True False
For a mobile operator, govt allocated 33 MHz of total bandwidth. If frequency division multiplexing is used, and two 25 kHz simplex channels are used for full duplex purpose, then estimate the total number of simultaneous users that can be accomodate by the operator.
A.a.Two electricians are discussing industrial cabling. Electrician A says that copper cable provides clearer transmission signals than fiber optic cable. Electrician B says that fiber optic cables will be larger thancopper cables with identical data transmission rates. Who is correct?B. Both Electrician A and Electrician B are correct.C. Only Electrician A is correct.D. Neither Electrician A nor Electrician B is correct. A.b. Two electricians are discussing industrial cabling. Electrician A says that signal losses in fiber optic cableare more likely to be caused by splices and connectors than cable length. Electrician B says that wire-wrapterminations should be used when there isn't enough time available to use IDC terminations. Who iscorrect?A. Only Electrician A is correct.B. Both Electrician A and Electrician B are correct.C. Only Electrician B is correct.
Higher bit rates can be achieved over voice grade line by employing M-ary modulation schemes TRUE FALSE
Q1.Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem in your submission.Consider a client-server system with the following parameters and requirements. The client transmits 10x106 bits of data every minute to the data server connected directly to it. The transmission link speed is 20x106 bps. Each packet is 2,000 bytes long which includes a 20-byte packet header.a. Calculate the number of packets generated per second for data transmission at the client node.b. The system requires every packet must be delivered within 4 ms of generating a data packet. Calculate the maximum link distance between the client and the server that still can meet this requirement. Ignore processing and queuing delays.c. Calculate the number of overhead bits transmitted per second from the client to the server.
Q2.Unless specified otherwise, use the free space propagation speed of light 3x108 m/s to calculate the propagation delay. For numerical calculations, the results must show the appropriate unit. Show a complete solution for each problem in your submission. Suppose network users share a 4 Mbps link. Also, suppose each user requires 200 kbps when transmitting, but each user transmits only 15% of time.a. When circuit switching is used, how many users can be supported?b. Suppose packet switching is now used and that there are 20 users. Find the probability that any given time, at most 4 users are transmitting simultaneously.