1. The bottom circular plate is slowly rotated at 2 rpm. The 0.1 inch gap, h between the top and bottom plates is filled with glycerin as shown. Determine the torque required to prevent the top plate from rotating. The diameter of the top and bottom circular plates is 12 inches. Neglect fluid transients at the edges. + H R

1. The bottom circular plate is slowly rotated at 2 rpm. The 0.1 inch gap, h between the top and bottom plates is filled with glycerin as shown. Determine the torque required to prevent the top plate from rotating. The diameter of the top and bottom circular plates is 12 inches. Neglect fluid transients at the edges. + H R

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter1: Introduction To Statics

Section: Chapter Questions

Problem 1.10P: A differential equation is d2ydt2=Ay2+Byt where y represents a distance and t is time. Determine the...

See similar textbooks

Similar questions

A differential equation is d2ydt2=Ay2+Byt where y represents a distance and t is time. Determine the dimensions of constants A and B for which the equation will be dimensionally homogeneous.
Explain why there is an “extra” term in the Bernoulli equation in a rotating reference frame.
Two pressure sensors are located at the seafloor: one is 100 m and the other is 500 m off the coastline. For a wave train of 10-s period, the pressure sensor closer to the shoreline measures the non-hydrostatic pressure amplitude as 5911 Pa and the other sensor measures the pressure amplitude as 4987 Pa. Given that the wave height is , what is the average bathymetric slope between the two pressure sensors? Take the magnitude of the gravitational acceleration as and the density of the seawater as . (Hint: Assume that the wave height has negligible variation between the two observation points.)
The blue cart has a fan attached and it’s mass is 660g. The red cart is 240 g. The other data necessary for the question is in the table provided below. Thanks!
A constant torque electric motor is used to drive the punching press. The pressis provided with a flywheel that rotates at maximum speed of 125 r.p.m. Theradius of gyration of the flywheel is 0.6 m. The press punches 200 holes perhour, each punching operation takes 1.5 second and requires 16 kNm ofenergy. Calculate the power of the motor and the minimum mass of theflywheel, if its speed is not to fall below 100 r. p. m
A 200-pound cube cargo of about 50 centimeters on the side. The static coefficient is 0.4 and the dynamic is 0.2. Calculate the maximum acceleration of the car that keeps the box from moving.
A cylinder with a piston diameter of 100mm supports astable mass of 100 kg vertically. a) Calculate the pressure generated at the base of the cylinder b) If the speed of this actuator is 0.1 m/sec, calculate its power Answer: a) 124 kPa b) 98.1 W
A 30 mm diameter shaft rotates in a 30.1 mm inner diameter and 60 mm long bearing with a frequency of 5000 rpm. At that frequency it can be assumed that the eccentricity is zero. The lubricant used is SAE-30 oil at 60 ° C (μ = 4 x 10-2 Nm-2s). What is the power absorbed by the mechanism? Remember that W = C. ω, Where: ω = angular velocity = 2πf, C = conjugate (moment or torque) and 1hp = 736W = 75 kg.m/s. Expected Answer: w = 0.38hp
The compressor shown has a mass of 250 kg and operates at 2000 rpm. At this operating condition, the force transmitted to the ground is excessively high and is found to be mrw2f. where mr is the unbalance and wf is the forcing frequency. To fix this problem, it is proposed to isolate the compressor by mounting it on a square concrete block separated from the rest of the floor as shown. The density of concrete is 2400 kg/m3 and the spring constant for the soil is found to be 80 × 106 N/m. The geometry of the compressor leads to choosing a block that is 1.5 m by 1.5 m. Determine the depth h that will reduce the force transmitted to the ground by 75 percent.
Compare the apparent frequencies of a 2550 Hz source moving away from you at 25 m/s and when you are moving away from the source at 25 m/s. Assume of 30 degrees Celsius.
A ship is 35 m long and is designed to move at 11 m/s. Laboratory experiments are carried out in a water tank with a 1 m long model. Find the velocity and the ratio of the resistive forces of the model. (r=1000 kg/m3)
A silo for storing grains has a height of 105 feet above the ground and a radius of 1.5 meters supplies grains in an industrial process. The SILO has at its base a pipe with a radius equal to 1.27cm that supplies the industrial process. To meet the needs of the industrial process, the supply pipeline must be capable of supplying grains with a volumetric flow of 2.5 L/Seg. (a) If the grains flow at the maximum amount, what would be the pressure in the pipe at the bottom of the SILO? (b) A smaller pipe, 0.5 in. in diameter, supplies another silo, at a distance of 23.6 feet above ground level. What are the flow velocity and the pressure of the beads in this pipe? CONSIDER A DENSITY FOR THE GRAINS OF 1.2X103Kg/m³ Answer part to: 6x105 Pascals answer part b: 24.3 m/s and 4.8x105 Pascals