1. Water at 60 °F flows from the basement to the second floor through the 0.75-in. (0.0625-ft)-diameter copper pipe (a drawn tubing) at a rate of Q = 120gal/min and exits through afaucet of diameter 0.50 in. as shown:Q=12.0gal/minK = 2 based on10 ft 10 ft →(/)|(8)pipevelocity(2)10 ftWide open5 ftglobe valve(4)0.50-in.diameter0.75-in.-diametercopper pipe(1)15 ft(3)Threaded90° elbowsDetermine the pressure at point (1) ifa. all losses are neglected,b. the only losses included are major losses, orc. all losses are included. 3. Use scale analysis to find an expression for S/L and Nu, for flow over a flat plate withboth boundary layers of equal thickness (8=ST)

To finddetermine the pressure at point (1) ifall losses are neglected the only losses included are…

1. Water at 60 °F flows from the basement to the second floor through the 0.75-in. (0.0625. ft)-diameter copper pipe (a drawn tubing) at a rate of Q = 120gal/min and exits through faucet of diameter 0.50 in. as shown: K₁ = 2 based on pipe 10 ft 10 ft→ (7)|(8) velocity 0.75-in.-diameter copper pipe 5 ft 10 ft Wide open globe valve 0.50-in. diameter 10 # 12.0 gal/min (3) (1) Threaded

1. Water at 60 °F flows from the basement to the second floor through the 0.75-in. (0.0625. ft)-diameter copper pipe (a drawn tubing) at a rate of Q = 120gal/min and exits through faucet of diameter 0.50 in. as shown: K₁ = 2 based on pipe 10 ft 10 ft→ (7)|(8) velocity 0.75-in.-diameter copper pipe 5 ft 10 ft Wide open globe valve 0.50-in. diameter 10 # 12.0 gal/min (3) (1) Threaded

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.24P: Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the...

See similar textbooks

Similar questions

Evaluate the Nusselt number for flow over a sphere for the following conditions: D=0.15m,k=0.2W/mK, hc=102W/m2K.
Engine oil at 100C flows over and parallel to a flat surface at a velocity of 3 m/s. Calculate the thickness of the hydrodynamic boundary layer at a distance 0.3 m from the leading edge of the surface.
Air at 1000C flows at an inlet velocity of 2 m/s between two parallel flat plates spaced 1 cm apart. Estimate the distance from the entrance to the point where the boundary layers meet.
Air at 20C flows at 1 m/s between two parallel flat plates spaced 5 cm apart. Estimate the distance from the entrance to the point at which the hydrodynamic boundary layers meet.
Solve part a. in Matlban with the following changes please: Flow Speed U_inf = 0.5 m/s Plate Surface Temperate Ts = 77 C Describe what each case represents in terms of the boundry layer
A vertical air stream flowing at a velocity of 100 m/s supports a ball of 60 mm in diameter. Taking the density of air as 1.2 kg/m³ and kinematic viscosity as 1.6 stokes, the weight of the ball that is supported is (if coefficient of drag C= 0.8)
We usually think of boundary layers as occurring along solid walls. However, there are other flow situations in which the boundary layer approximation is also appropriate. Name three such flows, and explain why the boundary layer approximation is appropriate.
The Blasius boundary layer profile is an exact solution of the boundary layer equations for flow over a flat plate. However, the results are somewhat cumbersome to use, since the data appear in tabular form (the solution is numerical). Thus, a simple sine wave approximation. is often used in place of the Blasius solution, namely, u(y) ≅ U sin (?/2 y/?) for y < ?, and u = U for y ≪ ?, where ? is the boundary layer thickness. Plot the Blasius profile and the sine wave approximation on the same plot, in nondimensional form (u/U versus y/?), and compare. Is the sine wave profile a reasonable approximation?
A gas at 20°C and 1 atm flow at 6 ft/s past a thin flat plate.At x = 3 ft, the boundary layer thickness is 0.052 ft.Assuming laminar flow, which of the gases in Table A.4 isthis likely to be?
A thin flat plate 20 cm by 90 cm is immersed in a 1m/s stream of water at 20 °c ( density=998, viscosity=0.001)the stream is parallel to the long side, compute the total friction drag considering both front and back sides of the plate
Mention the name of a technique which can be used to control the boundary layer
A fluid flows over a flat surface at 475 m/s. How much energy (in Joules) is generated in the boundary layer per kilogram of fluid? Give your answer to zero decimal places.