Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P-10 kN? Draw the FREE BODY DIAGRAM. 1.4 Axial loads are applied to the compound rod that is composed of an aluminumsegment rigidly connected between steel and bronze segments. What is the stress incach material given that P = 10 kN?BronzeAluminumSteelA= 400 mmA=600 mm2A= 300 mm2P3P4PP3m--5m4m

Drawing the FBD of each segment such that equilibrium is satisfied for each segment. Then using the…

1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in cach material given that P = 10 kN? Bronze Aluminum Steel A= 400 mm A=600 mm2 A= 300 mm 2P 3P 4P P 3m- -5m 4m

1.4 Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in cach material given that P = 10 kN? Bronze Aluminum Steel A= 400 mm A=600 mm2 A= 300 mm 2P 3P 4P P 3m- -5m 4m

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.6.3P

See similar textbooks

Related questions

Q: The rods AB and CD are made of steel with modulus of elasticity (Young's modulus) of E = 210 GPa and…

Q: : Determine the state of stress at point A on the cross section of the member at section a-a. 600 N…

Q: Prob. # 3] The torsional deformation of a steel shaft is 1° in a length of 2 ft when the shearing…

Q: The copper pipe has an outer diameter of 40 mm and an inner diameter of 37 mm. If it is tightly…

Q: Q3/ Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that…

A: The given figure is shown below:

Q: A В C 2m 1m 3m P Aluminum A=500mm2 A=900mm? E=70GPA L=2.0m Steel Detail of E=200GPA L=1.25m pin at O…

Q: PROBLEM 4: Find the elongation in a 2m long steel bar by subjecting it to 40 MPa stress. E = 200 GPa…

A: Given- Length of the steel rod (L) = 2m = 2000mm Stress in steel rod (σ) = 40MPa E= 200GPa=…

Q: 3. The tensile member shown, 60 mm x 90 mm in cross section is subjected to a load P=300 kN. The…

A: Solution Given Data: P= 300 KN Cross-section area A=(60mm×90mm) Angle with horizontal axis= 140

Q: The rod ABCD is made of an aluminum for which E= 70 GPa. Take P = 80 kN. NOTE: This is a multi-part…

Q: A rigid bar AB is hinged at A and is supported by a rod at C. The rod is pin-connected at D as…

Q: Q# 4: An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in Figure.…

A: Given:- The limited value of the P for bronze = 20 kN The limited value of the P for aluminum = 72…

Q: A rigid bar, the deformation of which may be neglected, is suspended from three rods and loaded as…

Q: The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Determine the state of…

Q: The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is…

Q: 3. The diameter of the steel rod d=10Omm, F=5kN, E=210GPA. Determine the maximum strain and the…

Q: 3. An aluminum bar having a cross-sectional area of 0.25 sq. in. carries the axial loads applied at…

Q: Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly…

A: For the section made of bronze - Stress in the section= σ1 σ1 = 2PA1⇒σ1 = 2×25×103400⇒σ1 = 125…

Q: For an element subjected to ox = 40 MPa (compressive), oy = 30 MPa (tensile) and txy = +20 MPa, the…

Q: The 1.16-in. diameter rod in (Figure 1) is subjected to the loads shown. Determine the state of…

Q: Figure 1 shows the cross-section of a lightly welded steel column under axial compression. The yield…

A: (a) The width of the flange is bf = 450 mm. The thickness of the flange is tf = 12 mm. The thickness…

Q: CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between…

A: NOTE: As per our company guidelines for multiple questions we need answer 1st question only

Q: Axial loads are applied to the compound rods that composed of an aluminum segment rigidlyconnected…

Q: Vertical rod CD of length L =2 m, cross-sectional area A = 150 mm2 %3D and modulus of elasticity E =…

Q: The wire BC has a diameter of 0.175 in. and the material has the stress-strain characteristics shown…

A: Using the equations of equilibrium we have, ∑MA=0FBC(50)-P(80)=0(i) when P=480 lbsFBC=768 lb…

Q: 67 lb/m 76 lb/m 2m 3m-

Q: The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Determine the state of…

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that d;…

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

A: Hi! Thank you for the question. As per the honor code, we’ll answer the first question since the…

Q: A solid steel bar of diameter di = 1.3 in. is enclosed by a steel tube of outer diameter dz = 2.45…

A: Given D1= 1.3 in d2= 1.95 in ,. d3 = 2.45 in T= 4900 lb-in G= 11.4× 106 psi

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: Bronze Aluminum Steel A = 400 mm² A=600 mm² A = 300 mm² 2P ЗР 4P -3 m- - 5 m- - 4 m

A: Given data:

Q: A hollow tube ABCDE constructed of Monel metal is subjected to five torques acting in the directions…

Q: 2.31 The three symmetrically placed rods support the rigid block of mass M. Before the block was…

Q: The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Determine the state of…

Q: Q2: The pin-connected structure shown in figure below consists of a rigid member BED and three steel…

A: Finding out elongation and stresses.

Q: Q2/ the structure shown below, support from fix at the left , the max normal at bronze =200 MPA,…

Q: A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown…

A: Given: Length of Steel rod, Ls = 1m Length of the copper rod, Lc = 2m Load, P =20KN Area of steel…

Q: 4. The shaft consisting of steel and aluminum segments carries the torques T and 2T as shown in the…

A: Given data Allowable shear stress in steel = 83 MPa Allowable shear stress in aluminum = 55 MPa…

Q: 2. Compressive centric forces of 30 kips are applied at both ends of the assembly to rigid plates.…

A: Determine the normal stresses in the steel core and the aluminum shell.

Q: The rigid bar ABCD supports point loads at A and D and is being supported by two bars at B and C.…

Q: A beam shown in Figure 7.7 is made of T beam, determine maximum shearing stress develop due to…

Q: 3. The beam shown below is suspended from two steel rods as shown and is initially horizontal. The…

Q: kN, čómputé the A rigid bar of negligible weight is supported and temperature change AT (°C) that…

A: Given- W=70KN For Bronze Rod L=1.5m A=300mm2 E=83Gpa For Aluminium Rod L=3m A=750mm2 E=70Gpa

Q: A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown…

Q: H.W 1 A 6 m long hollow bar of circular section has 140 mm diameter for a length of 4 m, while it…

A: GivenLoad, P=300kN=300×103NModulus of Elasticity=200GPa=200×109 Nm2=200×103 Nmm2Elongation, δl=?For…

Q: 3. The rigid bar of negligible weight is pinned at O and attached to two vertical rods. Assuming…

A: To find the largest load(P)-

Q: A hollow aluminum tube used in a roof structure has an outside diameter d2= 112mm and an inside…

Q: The 1052-kg uniform bar AB is suspended from two cables AC and BD each with cross-sectional area 475…

Q: 3. Two bars are rigidly fastened together and support a vertical load of 65 kN, as shown. The upper…

A: step 1-

Question

Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P-10 kN? Draw the FREE BODY DIAGRAM.

1.4 Axial loads are applied to the compound rod that is composed of an aluminum
segment rigidly connected between steel and bronze segments. What is the stress in
cach material given that P = 10 kN?
Bronze
Aluminum
Steel
A= 400 mm
A=600 mm2
A= 300 mm
2P
3P
4P
P
3m-
-5m
4m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
The plate welded to the end of the I-beam is fastened to the support with four 10-mm-diameter bolts (two on each side). Assuming that the load is equally divide among the bolts, determine the normal and shear stresses in a bolt. Express your answer in MPa.
A W 12 X 35 steel cantilever beam is subjectedto an axial load P =10 kips and a transverse loadV =15 kips. The beam has length L = 6 ft. (a) Calculatethe principal normal stresses and the maximumshear stress for an element located at C near the fixedsupport. Neglect the weight of the beam. (b) Repeat Parta for point D which is 4 in. above point C (see figure).See Table F-1(a), Appendix F, for beam properties.
What is the minimum required bolt diameter (mm) at C ifthe allowable bolt shear stress is 68 Mpa.a. 9 mm c. 11 mmb. 10 mm d. 12 mm Determine the stress (Mpa) in strut BC.a. 5.6 MPa c. 3.2 MPab. 2.8 MPa d. 6.4 MPa Calculate the bolt stress (Mpa) at A if its diameter is 20mm.a. 7.64 MPa c.11.46 MPab. 3.82 MPa d.14.92 MPa
The following solid aluminum bar (E = 10,000 ksi; α = 11.70E-06/F) is located between two fixed supports. Segment AB has a diameter of 3 inches and segment CB has a diameter of 2 inches. The load P is equal to 25 kip and the temperature increases by 50°F. Determine: a. The reactions at the supports. Answ: Cy = 17.938 kip (downward); Ay = 42.938 kip (upward). b. The deformation at point B. Answ: 2.693E-03 pulg. c. The stress in both segments. Anws: 5.709 ksi, 6.07 ksi.
The axial assembly consists of a solid 1.05-in.-diameter aluminum alloy [E = 9700 ksi, v = 0.29, 12.3 × 10−6/°F] rod (1) and a solid 1.4-in.-diameter bronze [E = 13300 ksi, v = 0.22, 9 × 10–6/°F] rod (2). Assume L1=17 in., L2=24 in. If the supports at A and C are rigid and the assembly is stress free at 10°F, determine: (a) the normal stresses , in both rods at 162°F (positive if tensile, negative if compressive). (b) the displacement uB of flange B (positive if to the right, negative to the left). (c) the change in diameter of the aluminum rod.
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.00 in. and a wall thickness of 0.223 in. is fastened to a solid 1.75-in.-diameter aluminum [E = 10,000 ksi] rod. The assembly is attached to unyielding supports at the left and right ends and is loaded as shown. Assume P=18 kips, Q=13 kips, L1=4 ft, L2=6 ft, and L3=6 ft. Determine(a) the stresses in all parts of the axial structure.(b) the deflections of joints B and C.
The axial load 396 kN applied to the lap joint is distributed equally among the three 20.6-mm-diameter rivets. What is the maximum tensile stress (in MPa) in the plate if w = 135.4mm and t = 27.1mm? Round off the final answer to three decimal places.
A steel bracket of solid circular crosssection is subjected to two loads, each of which isP = 4.5 kN at D (see figure). Let the dimension variablebe b = 240 mm.(a) Find the minimum permissible diameter dminof the bracket if the allowable normal stress is110 MPa.(b) Repeat part (a), including the weight ofthe bracket. The weight density of steel is77.0 kN/m3.
A full forming P= 52 kN axial force acts on the part shaped by the machining method made of xCy steel material. The thickness of the part is t= 20 mm and the steel tensile strength is sigma(tensile) = 620 MPa . Calculate the individual fatigue life of the A and B sections of the machine part for 90% reliability. Draw logarithmic S_N diagrams.
A prestressed beam has a width of 300 mm and depth of 600 mm. It is subjected to a bonded prestress tendon having an area of 590 mm2 acting at a distance 550 mm from the compression, face of the member. fc' = 34.6 MPa, fpu = 1860 MPa, fpy = 0.85fpu (stress-relived strands). COMPUTE THE DEPTH OF THE COMPRESSION BLOCK (mm)
Find the EIδ under 200lb load EIδδ under 400lb load