1.9 Consider Figure 2 and then determine the required parameters that follow. 2- -2- 10 15 20 25 30 35 TimeluSecs SuSecs/di Figure 2: Oscilloscope display of a square wave obtained via channel 1. Parameter Value Rise time (bottom to the top) Fall time (top to bottom) Pulse width (start to end in the middle of the pulse) Amplitude (vertical from peak to peak) Frequency (1 divided by cycle time) Number of complete cycles Signal 1/ V

1.9 Consider Figure 2 and then determine the required parameters that follow. 2- -2- 10 15 20 25 30 35 TimeluSecs SuSecs/di Figure 2: Oscilloscope display of a square wave obtained via channel 1. Parameter Value Rise time (bottom to the top) Fall time (top to bottom) Pulse width (start to end in the middle of the pulse) Amplitude (vertical from peak to peak) Frequency (1 divided by cycle time) Number of complete cycles Signal 1/ V

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter9: Measuring Instruments

Section: Chapter Questions

Problem 10RQ: 10. What electrical quantity does the oscilloscope measure?

See similar textbooks

Similar questions

Terms: amplitude (A), phase angle (ϕ), frequency (f), angular frequency (ω), period (T), peak value (Vp), peak-to-peak value (Vpp). Draw a 60 Hz, 5 Vp sine wave on a coordinate axis and graphically identify as many of the terms as possible from the previous section. Use voltage in volts for the y-axis, and time in milliseconds for the x-axis. You can use the blank OSC templates shown in the procedure section to draw the signals.
The period of this signal is about------ ms (milliseconds). The oscilloscope range selector determines the scale on the screen. That means number of volts per line for amplitude vertical (v/div) and the number of milliseconds per line for time horizontally (ms/div).
a)Does this Oscilloscope trigger on the rising or falling edge of the signal? b) At what voltage does the trigger signal reach that starts the Oscilloscope ‘Sweep’? c) What is the amplitude of the signal on Channel 1? d) What is the amplitude of the signal on Channel 2? e) What is the period of the signal on Channel 1?
Assuming XTAL=11.0592MHz, write a program to generate a square wave of 50 Hz frequency on pin P2.3.
A wave analyser is basically a superheterodyne receiver covering the following range of frequency with an IF of 100K Hz a. 5M Hertz to 5 5G Hertz b. 100kHertz to 100G hertz c. 100K hertz to 1M Hertz d. 20 hertz to 50k Hertz
Draw the time-domain plot of a sine wave with maximum amplitude of 15 volts, a frequency of 5, and a phase of 180 degrees
Find the average value of a half-wave rectified signal with a peak value of 20 mV. *Express your final answers in three decimal places with proper engineering prefixes, unless the answer is exact (terminating decimal).
A frequency modulated signal which is modulated by a 3-kHz sine wave reaches a maximum frequency of 100.02 MHz and minimum frequency of 99.98 MHz. Determine the peak frequency deviation in KHz. No unit in the final answer.
A frequency modulated signal reaches a maximum frequency of 74.073 MHz and a minimum frequency of 74.060 MHz when modulated by a 4.5 kHz wave. Find the peak deviation. ___________ kHz.?
Give the excitation table and transition table. State diagram too. K map too. Correct answer only
answer the following question. topic: oscilloscope 1. What is/are the function of the horizontal sensitivity (TIME/DIV)? 2.What is/are the function of the vertical sensitivity (V/DIV)? 3.. What are the functions of Oscilloscope? Function Generator?
How would you check the specifications of the pulse generator and make sure that it has a bandwidth that can support the square wave?Adjust the rise and fall times of the generator?