1.A series consist of 30 - 2 resistor , 0.15henry inductor, & a 0.15 uf capacitor,. If a variable frequency, 220 source is connected across its terminal, a) calculate the resonance frequency, for the condition of resonance, b) calculate the circuit current and power, c) the voltage drop across the resistor, inductor & the capacitor?

1.A series consist of 30 - 2 resistor , 0.15henry inductor, & a 0.15 uf capacitor,. If a variable frequency, 220 source is connected across its terminal, a) calculate the resonance frequency, for the condition of resonance, b) calculate the circuit current and power, c) the voltage drop across the resistor, inductor & the capacitor?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

HIGH VOLTAGE(Can you explain in detail? Thank you) Q1 : A 100 kVA, 50 Hz, 230/50 kV testing transformer has an 10% leakage reactance and a 2% winding resistance. A cable of capacitance 100 nF is to be tested at 300 kV using this transformer as part of the resonance circuit. Determine the value of the inductance (with a Q-factor of 20) required to obtain resonance and the value of the input voltage required to obtain the required voltage.
1. A series circuit consisting of a 40-ohms resistor, a 100-μf capacitor, and a variable inductor is connected two a 220-volt 60-cycle source. (a) Calculate the value of inductance L1, the current I, and the voltage drop across the inductor EL for the condition of resonance; (b) Determine the value of L, the current I, and the voltage drop across the inductor EL when the latter has its maximum value.
Tuned Circuit Design Using a VARICAP (a) Refer to the capacitance curves for the Motorola 1N4002 The input tuning circuit of a standard analog FM radio is given below. Specify, that is design for, a voltage, capacitance, and inductance required to tune the circuit to the center frequency of KUMD-FM which operates at 103.3 MHz. Sketching and labeling a representative resonance curve is required to support your calculations. There is no single correct design answer set of values since it depends upon the voltage you initially select to tune your diode.
A coil of resistance 20 Q and inductance of 300 mH is connected in parallel with a capacitance of 200 uF. The combination is connected across 200 V, variable frequency power supply. At what frequency will the parallel circuit resonate and what would be the current at resonance? [Ans 19.26 Hz, 0.431 A]
A 100 kVA, 50 Hz, 230/50 kV testing transformer has an 10% leakage reactance and a 2% winding resistance. A cable of capacitance 100 nF is to be tested at 300 kV using this transformer as part of the resonance circuit. Determine the value of the inductance (with a Q-factor of 20) required to obtain resonance and the value of the input voltage required to obtain the required voltage.
A circuit comprises of a coil (resistance of 20W, inductance of 400mH), and a capacitor of 2.0mF connected in series. A supply of 100V at 50 Hz is connected across the circuit. (i) Calculate the circuit: Impedance Phase angle Resonant frequency Q-factor Bandwidth (ii) How do each of the parameters in c., d., e., change if the coil is connected in parallel with the capacitor across the same supply?
A coil of resistance 100ohms and inductance 100uH is connected in series with 100pf capacitor .the circuit is connected to a 10v variable frequency supply. Calculate the resonance frequency, current at resonance, voltage across L and c at resonance and Q-factor of the circuit.
3. A series circuit consists of a 30-ohm resistor. a 0.104-henrv inductor, and a 40-microFarad capacitor. If a vanable frequencv I2U-volt source is connected across its terminals, (a) calculate the resonant frequency. fOr the condition of resonance, determine (b) the circuit current and power; (C) the voltage drops across the resistor, the inductor, and the capacitor Prepared bv ENGR. JEFFSON S. BALDEMECA
A coil of negligible resistance and inductance 100 mH is connected in series with a capacitance of 2µF and a resistance of 10 ohm across a 50V, variable frequency supply. Determine the resonant frequency, the current at resonance, the voltages across the coil and the capacitor at resonance, and the Q-factor of the circuit.
A circuit comprises of a coil (resistance of 20W, inductance of 400mH), and a capacitor of 2.0mF connected in series. A supply of 100V at 50 Hz is connected across the circuit. (i) Calculate the circuit: Impedance Phase angle Resonant frequency Q-factor Bandwidth (ii) How do each of the parameters in c., d., e., change if the coil is connected in parallel with the capacitor across the same supply? (iii)Explain what is happening to both parallel and series connections of the above circuit at resonant frequency and critically analyse the effects on circuit currents, voltages and components at resonance.
Suppose the noise power at the input to a receiver is 5 nW in the bandwidth of interest. What would be the required signal power for signal–to–noise ratio of 30 dB? full solution thank you for the help!
please Calculate the gain margin, phase margin and magnitude of bode plot for the transfer function