1.Given that a particular continuous-time LTI system has the input x(t) and the impulse response h(t) as shown in the figure, do the following. (a) Find the system output y(t) for the time period 4 sts 5. (b) What will be the maximum value of the output (over all time)? Find all ranges of time for which the output will be zero. 2 6. h(t) + 3 2 1

1.Given that a particular continuous-time LTI system has the input x(t) and the impulse response h(t) as shown in the figure, do the following. (a) Find the system output y(t) for the time period 4 sts 5. (b) What will be the maximum value of the output (over all time)? Find all ranges of time for which the output will be zero. 2 6. h(t) + 3 2 1

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The block diagram of a time-invariant, linear, continuous-time system is given below. X1(s) and X2(s) are the state variables of the system. U(s) is the input signal of the system, Y(s) is the output signal of the system. What is the value of parameter E?
Consider an LTI system with impulse response h(t) as illustrated infollowing figures. Find out the output y(t) for a given input x(t) as shown in following figures.
An LTI system has an impulse response: h(t) = e^(4t)u(t+1) This system is: NEED A NEAT HAND WRITTEN SOLUTION OTHERWISE WILL LEAVE A DOWNVOTE ? NO CHAT GPT
When the unit step function is applied to the system input whose block diagram is given below, the output response is c(0.2) = 0.11 for t=0.2 s, and c(infinity)=0.333 for t=infinity. What is the settling time of the system? calculate.
2) Find a) the impulse response, b) the step response of the following causal-LTI system. Do all computations in time domain. 21 on (1) V 412 |- y(t) v
A causal linear time-invariant continuous-time system has impulse response h(t) = e-t +sin(t) , t >= 0 Compute the output response for all t>=0 when the input is the unit-step function u(t).
D.) It is known that u(t) is a unit step signal and a Linear Time Invariant (LTI) system has an impulse response given by h(t) = (4t+1) u(t–2) + (-4t–1)u( t). The LTI system above is then evaluated by passing the input signal x(t) = 2u(t–1) –2u(t–2) into the system. a) Show mathematically whether the above system is a stable system or not and explain your answer completely and explain whether the system is a causal system! b) Draw the input signal for the system above and also describe the impulse response of the system! c) If y(t) is the output signal of the LTI system above, then determine the value of the y(t) signal for each t value!
circuit analysis 2In the circuit shown below, the value of vc (t) for 0 ≤t< 1 is equal to which of the following?
The impulse response of a continuous-time LTI system is given byh(t) = u(t) −u(t − 5) where u(t) is the unit step function.a) Find and plot the output y(t) of the system to the input signal x(t) = u(t) using the convolution integral.b) Determine stability and causality of the system.
The closed-loop transfer function of a system is given by G(s) = 14.145 / (s+5)*(s^2 +0.842s+2.829). Which of the following is true for this system? I. The damping ratio is given by 0.25. II. Its natural frequency is given as 1.682 r/s. III. Exceeding the percentage is given with 44.4%. IV. The peak time is given as 1.93 s. a) I only b) I, II, II and IV c) II and III only d) I, II and IV only
A single-pole causal LTI system has the following impulse response given below.
The transfer function of a Causal LTI system is given below. impulse of the LTI system Calculate the answer.