10-4 A PWR operates at 2000 psia and 600°F hot leg. It has a 1000 ft' pressurizer which is normally half full of water. The primary loop is 10,000 ft in volume. The hot leg temperature suddenly rose to 605°F. Calculate (a) the final composition of the pressurizer, and (b) the final system pressure. Ignore spray flow and heat.

10-4 A PWR operates at 2000 psia and 600°F hot leg. It has a 1000 ft' pressurizer which is normally half full of water. The primary loop is 10,000 ft in volume. The hot leg temperature suddenly rose to 605°F. Calculate (a) the final composition of the pressurizer, and (b) the final system pressure. Ignore spray flow and heat.

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 9RQ: The evaporator design temperature may in some cases operate at a slightly ____(higher or lower)...

See similar textbooks

Similar questions

i . A gas well is flowing at a flow rate of 1.2x105scf/d with the surface pressure of 500psi and compressor inlet pressure of 100psi. Calculate the horse power requirement.
A 1200 kW water-cooled chiller has a centrifugal compressor with refrigerant R134a as the working fluid. The compressor runs at 9600 rev/min and has a slip factor of 0.95 and an overall isentropic efficiency of 90%. The impeller tip speed is not to exceed 160m/s. The evaporating and condensing temperatures are 2°C and 40°C respectively. Assuming that there is no superheating and sub-cooling, a) sketch the refrigration cycle on a P-h diagram (please indicate the pressures and specific enthalpies of all points in the cycle); b) determine the mass flow rate of the refrigerant R134a; c) determine the coefficient of performance of the chilled water plant; and discuss the possible measures to uplift the plant COP d) determine the number of stages and the impeller tip diameters, assuming that all stages would share same work input and each stage compression would have the same impeller tip diameter. e) Please also comment how the slip factor can affect the energy performance of the…
air at 30 ℃ and RH 40% flowed to the heating coil so that the dry bulb temperature was 80 ℃. then air is used to dry it by passing it into a pile of granulated pet food. The air coming out of the pile has a dry ball temperature of 60 ℃. This air is then reheated to 80 ℃ and flown into the pile of other pet food. the air coming out of the second dryer is in a saturated state. Describe the processes that occur from ambient air to saturated air from desiccant 2 in a psychometric diagram. determine the amount of water discharged in the first and second dryers per kg of dry air. a. first dryer ... (kg water / kg air) b. second dryer ... (kg water / kg air)
If feedwater is supplied at 50 degrees Celcius, a boiler generates 10,000 kg/hr of steam at 98% quality at 1 MPAA. Determine the (a) rated boiler horsepower if the boiler operates at 150% of its rating, and (b) what is its probable heating surface?
The compression ratio in a gasoline engine is 8. The total cylinder volume of the engine (for the bottom dead point) is 600 ml, and air enters the cylinders at a temperature of 20 ° C and a pressure of 100 kPa andThe maximum temperature of the cycle is known as 1500 ° C. a) Calculate the heat input in the cycle in kJ. b) Calculate the thermal efficiency of the cycle c) Calculate the power generated in the cycle.
A diesel engine compresses air whose temperature is 27°C and pressure is 95 kPa. At the end of the heat treatment the pressure in the cylinder becomes 7.2 MPa and the temperature is 1900°C. Calculate : a) compression ratio of the engine b) Cutoff ratio c) Thermal efficiency of the engine d) Average effective pressure
Can I ask for the schematic diagram of this? and also the Ts diagram and Ph diagram. Thank You! Catalogue data for R-32 compressor with a displacement of 80 L/s show the capacity to be 8 tons when the suction conditions are 0.2 MPa and -20°C and condensing temperature is 50°C. The refrigerant leaves the condenser as saturated liquid. Calculate the actual volumetric efficiency and the brake work of the compressor if the compressor efficiency is 65%.
A four stage single acting air compressor running in an atmospheric at 87 KPa and 15 degrees Celsius has a free air delivery of 2,83 m³/min. The section pressure and temperature are 80 KPa and 32 degrees Celsius respectively, the delivery pressure is to be 7 MPa. The temperature at the start of compression in each stage is 32 degrees Celsius, take n=1.3 for all stages. Calculate : 1. The intermidiate pressure ratio in 3 decimal place 2.The intermidiate pressure at first, second and third stage in KPa 3. The mass flow rate in kg/min 4.The power input in KW
10x106 ft3 of a gas at 60 °F and 760 mmHg must be delivered to a power plant per 24-hr day from a company 5 miles away. Delivery conditions are to be 60 °F and 10 psig at the plant. a. If the gas leaves the compressor at a temperature of 75 °F, what must be the pressure (in psia) at this point? The pipe is stainless steel with 20 inch Inner Diameter.
A pharmaceutical company plans to install a solid fuel fired boiler for its daily usage. The desired capacity of the steam generation is 1.25 kg per second at pressure of 1.15 MPa and temperature 215oC. Feed water at average temperature of 25oC, is to be fetched from nearby reservoir. The consumption of the solid fuel having calorific value of 25.7 MJ/kg is 375 grams per second. Evaluate the enhancement of efficiency of the boiler if the following accessories are coupled with it. i) Economizer that increases the inlet feed water temperature by 63⁰C and reduces the fuel consumption by 18%. ii) Air-preheater that reduces the fuel consumption by 26%.
A chemicals company wants to optimize the power consumption of their air compressors. Their Design Engineers proposed to replace their Single-stage Adiabatic Compressors with the following: a. Isothermal Compressorb. Two-stage Compressor with intercoolingc. Four-stage Compressor with intercooling In order to justify the replacement, the percentage of the energy per mass (J/g) saved by each proposed compressor system should be calculated. Savings should be at least 40%. Determine which of the three proposed compressors will meet the criterion. The flow rate of air required is 600 ft3/min at 70 °F and 14.7 psi, which should be compressed to a final pressure of 2,000 psig. The relative molecular mass of the gas is 28, isentropic constant is 1.40, and density of air is 1.204 kg/m3.
1) A singe acting, twin cylinder, ammonia compressor with bore equal to stroke is driven by an engine at 250 rpm. The machine is installed in a chilling plant to generate 700 kW of refrigeration at -18C evaporating temperature. At this temperature, the cooling effect per kg mass is 1160 kJ. The sp volume of vapor entering the compressor is 0.592 m³/kg. Assume 85% volumetric efficiency. Calculate the bore in mm.