10) In case of architectural restrictions, the designer must: A) Place the rebars periodically B) Make the cross section (double reinforced) C) Make the cross section (winged) D) Change the cross section regardless of the architectural plan What is the answer? A or B or C or D?

Q: Describe the construction of various types of hollow-core metal doors?

A: most common type of door which used in commercial and industrial uses. these door supported on hinge…

Q: observe and describe the functionality and aesthetic aspects in their design.

A: By observing the picture it can be seen that the area is of restaurant or dinning area of a hotel.…

Q: What would be the best material for burglar bars and how would it be protected from corrosion

A: Most burglar bars are made of metal, usually steel, aluminium, or iron. But The best material used…

Q: What is the minimum clear spacing between parallel bars

A: What is minimum spacing of reinforcement? In order to have properly anchored reinforcement it is…

Q: Identify what type of structure is shown. Hinge Hinge a. Frame b. Truss C. Beam d. Arch Type of…

A:

Q: What type of plastic weathers well and is used for exterior purposes, such as siding, gutters, and…

A: Polyvinyl chloride (PVC) is the type of plastic used for exterior purposes. It is mainly used for…

Q: Choose the correct answer Temporary bridges are built from a-Stones b-Steel c-the wood d-Nothing…

A: The temporary bridges are mostly built by using the prefabricated steel girder, steel plates, and…

Q: All specific sizes recommended by CRSI below meet minimum requirements of ACI 318 Recommended End…

A: The Standard Specifications require that reinforcing steel hooks and bends conform to the provisions…

Q: 得分 -- Explanation of technical terms 1. Design working life 2. Degree of reliability 3. Design…

A: Structural engineering — a forte inside the field of civil designing — centers around the system of…

Q: All fixed metal parts that are within_ft horizontally of the inside walls of a permanently installed…

A: The question asked is descriptive.

Q: Scaffold platforms must O Be fully planked O Be at least 18 inches wide O Be free of debris O All of…

A: Given data in question  Scaffold platforms To be discussed  Provisions of scaffold   The scaffold…

Q: Describe fire-protection procedures for structural steel members required by building codes?

A: The fire-protection procedures for structural steel members required by building codes are:

Q: QUESTION 3 If you use computer program to analyze your reinforced concrete structure, the…

A: Deformed reinforcement in frame members sustaining earthquake-induced flexural and axial stresses…

Q: omprehensive definition for detailing of reinforcement bar (stee

A: Solution: Rebar is basically used in order to improve the concrete tensile strength as concrete is…

Q: Define Steel bars and how many types of stell bars and  given details of sizes of stell bars.

A: The steel bars are defined as the mesh of various steel wires used in reinforced concrete and…

Q: What is under reinforced section.

A: Answer  Under reinforced section ie term used in design of concrete structures  It means the…

Q: What standard diameter deformed bar used as stirrups for beam?

A: A stirrup is  a closed loop of reinforcement bar. Its main purpose is to hold the reinforcement bars…

Q: Determine the following: a. How many additional ɸ16 tensile bars are required? b. What is the new…

A:

Q: General Specification for Civil Engineering Works (1992 Edition) Clause 15.09 specifies that tying…

A: Answer Plain steel tying wire mainly used for the reinforcement adjacent to class F4 and F5 finish

Q: A roof framing plan for a building is shown below in Figure 1.  The columns are 20 feet high.  The…

A: Given data   columns are 20 feet high.  The flange width for the W12X35 is 6 ½ inches and the flange…

Q: Discuss defects of Timber in detail, also draw a neat and clean diagram for each defect.

A: Solution: There are mainly 5 types of defects in timber:1. Defects due to natural Forces2. Defects…

Q: Discuss the different types and properties of reinforcing steel bars a. Steel grade designation and…

A:

Q: Draw a neat and clean diagram of the final configuration of how the bars are placed.

A: To draw the bar configuration of the given beam

Q: In what type of building code article would you see a statement describing in detail the nailing…

A: QUE:- in what type of building code article would you see a statement describing in detail the…

Q: Identify and enumerate the different safety standards in carpentry works and metal bench works.

A: 1. Always Wear the Safety Equipment It is one of the important factor to remember. During the usage…

Q: It is properly selected and mounted on a location most feasible and effective with minimum cost. * O…

A: It is completely dependent on type of work and requirements, where the lighting has to be fixed. For…

Q: A cantilever beam has a length of 2 m and 646 mm depth. Is the beam depth permissible by the code?…

A: The effective depth of the beam is assumed based on the length to depth ratio.  The length to depth…

Q: Define how can we design the tie bar (spacing, diameter and length), in which standard the design is…

A: spacing between two consecutive tie bars is known as pitch.the spacing between tie bars are taken as…

Q: Please describe the general requirements of steel bar installation and the main contents of…

A: The factors that influence steel bar installation involves its mechanical properties. Steel derives…

Q: Why clamp handles are used?

A: Lifting the handle's body, twisting it to the appropriate position, and releasing it creates a…

Q: )      Differentiate b/w the following:   i) Ultimate limit states & Serviceability limit states

A: (As you have asked multiple questions, we will be providing a solution for the first one according…

Q: Question. 1. What are modern challenges that steel construction are still facing and keeping steel…

A: Steel structures are types of metal structures used in the constructions. These steel structures are…

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.