10 in. 10 in. 0 = 45° k = 2 lb/in. Prob. R11-2

Q: Draw the Free Body Diagram

A:

Q: 0.6 m 03 m -1m-1.50 m- 0.75 m

A: Consider it as simply supported beam and determine reactions at A and B

Q: The pipe is held in place by the vise. If the bolt exerts a force of 50 lb on the pipe in the…

A: Drawing the line of action of forces as shown below – Writing Lami's theorem:-

Q: The jib crane is supported by a pin at C and rod AB. If the load has a mass of 1.89 Mg with its…

A:

Q: Determine the force in each cable needed to support the 500-lb load.

A: Consider the diagram of the figure with the forces as shown below. Here point C is taken as origin.

Q: Q 26/ Determine the force in member CM of the loaded truss. 4m 4m E 4m -4m 4m |D F G M L K Bo L L L…

A:

Q: The uniform rod of length L and weight W is supported on the smooth planes. Determine its position 0…

A: Apply the conditions of equilibrium…

Q: 8. Determine the maximum weight of body B that will permit the homogeneous 50-lb. block A to slide…

A: As per given question  Weight =50lb Friction =0.3 R=10 in r=5 in We have to find maximum weight of…

Q: The scissors linkage is subjected to a force of P = 150 N. Determine the angle θ for equilibrium.…

A:

Q: Identify the zero force members (if any) in the trus 4 m - 3 m 3 m- P;

A: GIVEN DATA- Given Truss   we have to find zero force member in truss

Q: Determine the force F to move the blocks A and B to the right. The two blocks are being connected by…

A:

Q: 6 Determine the stretch in each of the two springs required to hold the 50-kg crate in the…

A:

Q: 11-25 A frame is loaded and supported as shown in Fig. P11-25. If the weight of block A is 500 lb…

A: Write the coordinates of the point G and F where the forces are acting in terms of the angle θ…

Q: Determine the stretch in each spring for equilibrium of the 2-kg block. The springs are shown in the…

A:

Q: 0.25 m 0.25 m 1.5 m E 30° H D 10° 2 m 60° 0.5 m

A:

Q: The 10 lb weight is supported by the cord AC, a roller and by a spring. If the spring has an…

A:

Q: The uniform bar AD has a mass of 20 kg. If the attached spring is unstretched when θ = 90°,…

A: Free body diagram Given Mass M = 20 kg Spring index k = 2 kN/m a = 0.5 m b = 1 m To find…

Q: The two bars each have a mass of 8 kg. Determine the required stiffness k of the spring so that the…

A: Draw the free body diagram.

Q: The flywheel is subjected to a torque of M = 75 N ⋅ m. Determine the horizontal compressive force F…

A: The free-body diagram of the problem can be sketched as follows, The flywheel has only one degree…

Q: 03. The automobile has a mass of 2 Mg and center of mass at G. Determine the towing force F required…

A: Draw a free body diagram for the problem. Here, NA and FA indicate the normal reaction at A and the…

Q: The clamp is adjusted so that it exerts a pair of 145-N compressive forces on the boards between its…

A: Taking the lower part of the clamp and drawing the free body drawing for the lower part –

Q: The uniform rod of length L and weight W is supported on the smooth planes. Determine its position 0…

A:

Q: Draw the free-body diagram for the following problem. The rod shown.

A: Let, HA be the horizontal support reaction at point A, and RA be the vertical support reaction at A.…

Q: The disk B has a mass of 20 kg and is supported on the smooth cylindrical surface by a spring with…

A:

Q: Detemine the force in each cable and the force F needed to hold the 4 kg lamp in the position shown.…

A:

Q: 11-34 Determine the horizontal and vertical components of the reaction at support A of the two-bar…

A: Draw the FBD and take Force analysis and Moments about pivot points to arrive at the answer as shown…

Q: The wall crane supports a load of 700 lb. Determine the horizontal and vertical components of…

A: Let's first draw the free body diagram of the pulley, E Consider the tension in the ropes attached…

Q: The grinder has a force of 400 N in the direction shown at the bottom. The grinder has a mass of 300…

A: Given  Mass of Grinder = 300 Kg      To determine  Force in Hydraulic Cylinder DF

Q: Determine the horizontal and vertical components at A and C. Assume the frame is pin connected a…

A:

Q: F3-4. The block has a mass of 5 kg and rests on the smooth plane. Determine the unstretched length…

A:

Q: Determine the reactions at the supports. EI is constant.

A: Given dataUDL = 6kN/m

Q: The 30-N force causes the bar to tip 8 = 15 when the force is applied. Originally the bar is…

A: Given   Force at point C, Fc = 30 kN                        Angle = 15o Find   Stiffness of the…

Q: The 300 kg uniform I-beam supports the 120 kg load. What are the reactions at the supports A and B?…

A:

Q: The 100 kg block is supported by two springs having the stiffness shown. Determine the stretch of…

A:

Q: Determine whether or not it is stable for that position. R=0.75m h=1.50m

A:

Q: 4. Determine the force created in the hydraulic cylinders EF and AD in order to hold the shovel in…

A:

Q: The wall crane supports a load of 700 Ib. Determine the horizontal and vertical 4n components of…

A: Make a Free body diagram of the given figure.

Q: Q (4): The 11 Kg lamp fixture is suspended from the two springs, each having an unstretched length…

A:

Q: The linkage is subjected to a force of P = 6 kN. Determine the angle θ for equilibrium. The spring…

A: Given: The force acting on point B, P = 6 kN The spring stiffness, k = 20 kN/m The length of side AB…

Q: The weight of the uniform bar AB is W. The stiffness of the ideal spring attached to B is k and the…

A:

Q: The disk has a weight of 12 lb and is pinned at its center O. A vertical force of P = 2 lb is…

A: To calculate the angular velocity of the disk after 4 seconds, we will use the Newton's second law…

Q: 3–46. Determine the stretch in each of the two springs required to hold the 20-kg crate in the…

A:

Q: 9. Outriggers A and D are used to stabilize the crane from overturning when lifting large loads. If…

A:

Q: Determine the angle θ for equilibrium and investigate the stability at this position. The bars each…

A: Consider the diagram of the truss as shown below. The point A is considered as the datum. The…

Q: Please give me a step by step answer to the following question

A: Consider the stretched length of the spring AB be l’AB, lAB be the unstretched length of the spring,…

Q: The cantilevered jib crane is used to support the load of 780 lb. If the trolley T can be placed…

A: Given : Load on crane = 780 lb            Let the reaction on collar B in vertical direction be  =…

Q: The two A-36 steel bars have a thickness of 1 in. and a width of 4 in. They are designed to act as a…

A: let the density of the A-36 steels bars  are  ;ρ=7.85×103 kg/m3 ;   -------From standard valueE=200…

Q: Find the true magnitude and direction of the forces at all the supports A and B of the truss at…

A:

Q: The constant moment of 50 N ⋅ m is applied to the crank shaft. Determine the compressive force P…

A: Understand that these a single degree of freedom problem and on independent variable θ can…

Q: Determine the horizontal and vertical components of reaction which the pins exert on member EDC of…

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.