-10- Magnitude (dB) -5 -15 -20 -25 -30 Phase (deg) -35 Or -90 R₁ C₁ 10³ Bode Plot of 1st Order RC Circuit Frequency (rad/s) 104 105 Above are a 1st Order RC filter and its bode plot. For the above circuit, assume wc = 2,272.73 rad and C₁ = 0.22μF: A) Determine which kind of filter (Lowpass, Highpass, Bandpass, Notch) is the above circuit. B) Find the magnitude of the transfer function at the corner frequency, H(w = wc), in units of dB. C) Find R₁ in units of kn. D) Using the Bode Plot, find the approximate frequency fi in units of kHz at which |H(f₁)| = -25dB. E) Using the Bode Plot, find the approximate |H(w = 7,000 rad)|linear (no units). F) Assume at w = 7,000, Vin = 10/45°V and ZH(w) = -72°. Using these assumptions and Part E, find Vout at w = 7,000 rad in Avout 40vout form and in units of [V]4[°]. sec sec

-10- Magnitude (dB) -5 -15 -20 -25 -30 Phase (deg) -35 Or -90 R₁ C₁ 10³ Bode Plot of 1st Order RC Circuit Frequency (rad/s) 104 105 Above are a 1st Order RC filter and its bode plot. For the above circuit, assume wc = 2,272.73 rad and C₁ = 0.22μF: A) Determine which kind of filter (Lowpass, Highpass, Bandpass, Notch) is the above circuit. B) Find the magnitude of the transfer function at the corner frequency, H(w = wc), in units of dB. C) Find R₁ in units of kn. D) Using the Bode Plot, find the approximate frequency fi in units of kHz at which |H(f₁)| = -25dB. E) Using the Bode Plot, find the approximate |H(w = 7,000 rad)|linear (no units). F) Assume at w = 7,000, Vin = 10/45°V and ZH(w) = -72°. Using these assumptions and Part E, find Vout at w = 7,000 rad in Avout 40vout form and in units of [V]4[°]. sec sec

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A series RLC circuit is formed using component values R=100 and L=1.5 mH, together with a source that provides a sinusoidal voltage Vs (t). If the quality factor in resonance condition is Q0 = 7, determine: a) the magnitude of the impedance at 500 Mrad s-1b) the current that circulates if vs (t) = 2,5V cos (425 ×10 6t) Note: Vent (input voltage). Vsal (output voltage)
Design a fourth-order low-pass filter with a cutoff frequency of 500 Hz and apassband gain of 10. Use 1 μF capacitors. Sketch the Bode magnitude plot forthis filter.
A mass-spring-damper system is shown below and its transfer function is given. Find the spring constant, mass, and damper constant k,m,c of the system according to the Bode diagram given below. Reminder: The starting point of the red line corresponds to -26dB. ζ=0.32. The frequency corresponding to the sloping peak of the red line ω=ωn =3.2
For a passive low-pass filter circuit that you will design using resistor and capacitor elements. a)Find the transfer function of the circuit. b)Examine the frequency response of the filter circuit by taking the Vinput =10cos(2π300t) and the R and C elements as the last two digits of your student number. c) Find the cutoff frequency (wc) in Hz. d)Calculate the bandwidth and phase shift value. e)Find the output voltage (Voutput) The last two digits are 02
753. For the transfer function (TF) 2s/(s+3) and resulting Bode Plot, calculate the gains (dB) at the corner, one decade below, and one decade above. Also calculate the phase (deg) of the TF at the same three frequencies. Last answer is w_corner (rad/sec) Find: gdB_corner_f, gdB_low_f, gdB_high_f, phase_corner_f(deg), phase_low_f(deg), phase_high_f(deg), w_corner(rad/sec)
If my input to this RLC bandpass filter is a 2V AC sinusoidal wave, how would I determine the attenuated Vout? Please feel free to assign values for R,L and C.
Exercise 3.1 Construct a lowpass Butterworth filter with the following conditions: Amax= 0.7dB. Gain= 0dB Fp= 30kHz Must have 5 poles. For such a filter build: A)Draw the bode diagram for the amplitude and phase. B)iFor a frequency Fs= 45kHz, determine Amin.
For a passive low-pass filter circuit that you will design using resistor and capacitor elements, a) Find the transfer function of the circuit. b) Examine the frequency response of the circuit for Vinput =10cos(2π300t) and R=1 ohm and C=1 F. c) Find the cutoff frequency (wc) in Hz. d) Calculate the bandwidth and phase shift value. e) Find the output voltage (Voutput).
From using the values from the image with the circuit I found that wc or the corner frequency would be R/L or 1315789.474 rad/s. But I don't understand how to do the bode plot for the high-pass circuit
Hi, for this question, can I use 1 1st order LPF and 1 1st order HPF in cascade to design the filter circuit? If so, how would I solve this question. Thank you.
Sketch a Bode plot, using straight-line approximation, for the range of frequencies from 1 Hz up to 1 MHz. Include magnitude and phase plots. put magnitude in dB. Graph should include: -how fast the transfer function “rolls off” below the cut-off frequency (in dB/decade) -the phase and amplitude for the three frequencies: ω = ωC, ω = 10∗ωC, ω = 0.1∗ωC fc = 500 Hz ωC = 2π(fc) This is for a passive high pass filter (single resistor, single capacitor)
Exercise 3.1 Construct a lowpass Butterworth filter with the following conditions: Amax= 0.7dB. Gain= 0dB Fp= 30kHz Must have 5 poles. For such a filter build: A)Draw the bode diagram for the amplitude and phase. (use software if you need it)