10 mm Weld 20°

Q: 1200 N A strain gage located at C on the surface of bone AB indicates that the average normal stress…

A:

Q: Determine the values of the stress in portions AC and CB of the steel bar shown Fig. when the…

A:

Q: Knowing that the hole has a diameter of 9 mm, determine (a) the radius rf of the fillets for which…

A: Write the expression of the radius of the hole. Write the expression of the effective width of the…

Q: Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature at…

A:

Q: A 1-in. square (thickness 0.12-in) plate was subjected to a uniform load of 0.72 kip/in in the…

A: Givensquare platea=1int=0.12inFx=0.72 kip/inFy=1.44 kip/inE=29×106 psiv=0.3

Q: PROBLEM 2.1 A steel rod is 2.2 m long and must not stretch more than 1.2 mm when a 8.5 kN load is…

A:

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A: Given that: For the rod consisting of two cylindrical portions: For AB, material is steel LAB = 250…

Q: The storage tank shown contains liquefied propane under a pressure of 1.4 MPa at a temperature of 38…

A:

Q: 1. Two steel plates are to be held together by means of 16-mm diameter high- snugly inside…

A:

Q: Determine the average normal stress in each of the 20-mm diameter bars of the truss. Set P = 40KN.…

A:

Q: 1. A strain gage located at C on the surface of bone AB indicates that the average normal stress in…

A: Data given-  Stress = 4.80 MPa  Force = 1200 N  do = 25 mm

Q: Each of the four vertical Ilinks has an 8 x 36-mm uniform rectangular cross section and each of the…

A: Given: The load, P = 19 kN The area of vertical rectangular cross-sectional, A = 8x36 mm2 The pin…

Q: Knowing that the allowable stress in section ABD is 80 MPa, determine the largest force P that can…

A:

Q: The aluminum rod ABC (E = 70 GPa), which consists of two cylindrical portions AB and BC, is to be…

A: Given   Load, P = 126 kN Allowable stress = 165.5 MPa Young's modulus, EAC =70 GPa…

Q: .. Knowing that the allowable stress in section ABD is 70 MPa, determine the largest force P that…

A:

Q: 7.118 For the tank of Prob. 7.117, determine the largest allowable gage pressure, knowing that the…

A: 7.117.. Given, Diameter of vessel, d=1.6mThickness of the cylinder, t=8mmNormal stress perpendicular…

Q: PROBLEM 2.2 A 1.5 m long steel wire of 6 mm diameter steel wire is subjected to a 3.4 kN tensile…

A:

Q: At a temperature of 28.75 °C a 0.4-mm gap exists between the ends of the rods shown. At a later time…

A:

Q: Knowing that, for the plate shown, the allowable stress is 136 MPa, determine the maximum allowable…

A: given data, allowable stress =136MPa diameter DA = 20mm db = 50 mm p max? when no stress…

Q: 1. Knowing that the ultimate load for cable BD (diameter is 20 mm) is 110 kN and that a factor of…

A:

Q: Knowing that the allowable stress in section ABD is 10 ksi, determine the largest force P that can…

A: Given data: The allowable stress in the section ABD is; σallow=10 ksi. Evaluate the cross-section…

Q: A steel pipe of 12-in. outer diameter is fabricated from 14-in.-thick plate by welding along a helix…

A: Given data: Outside diameter of pipe, d2=12 in Thickness of the plate material used in fabricating…

Q: The boom AB is made up of a hollow square 100-mm tube having a wall thickness of 5 mm. A 10-mm…

A: Given data, Outer dimension of hollow boom AB is 100 mm and thickness is 5 mm. So, cross-sectional…

Q: Two horizontal 5-kip forces are applied to pin B of the assembly shown. Knowing that a pin of…

A: Given Data: Horizontal forces on pin is F = 5 kips +5 kips = 10 kips. The width of link AB and BC…

Q: A timber beam AB of length L and rectangular cross section carries a single concentrated load P at…

A: (a) Given Data Length of AB is : L Load at midspan is : P Area of cross-section is : A=b×h Now due…

Q: Link BD consists of a single wooden member 38.2 mm wide and 20.4 mm thick. Knowing that each pin has…

A:

Q: A load P is applied to a steel rod supported as shown by an aluminum plate into which a…

A: Given d=0.6 in t=0.4 in From the fig Shear stress can be given as τ=FAWhere F=Pτ=PA

Q: Knowing that the central portion of the link BD has a uniform cross- sectional area of 800 mm²,…

A:

Q: Rigid triangle ABC is pinned at B and supported by a steel-reinforced aluminum shaft at A and an…

A: Given Rigid triangle ABC is pinned at B and supported by a steel-reinforced aluminum shaft at A and…

Q: An offset h must be introduced into a metal tube of 0.75-in. outer diameter and 0.08-in. wall…

A:

Q: For the truss and loading shown, determine the magnitude of the normal stress(in psi) in member CE,…

A:

Q: Link BD consists of a single wooden member 38 mm wide and 19.2 mm thick. Knowing that each pin has a…

A: Width of link BD, b= 38 mm Thickness of link BD, t= 19.2 mm Diameter of the pin, d= 14.30 mm θ= 0∘…

Q: A 6.87-m-long steel rod must not stretch more than 2.5 mm and the normal stress must not exceed 181…

A:

Q: At room temperature (20 °C) a 0.8 mm gap exists between the ends of the rods shown. At a later time…

A:

Q: PROBLEM 1.2 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.…

A:

Q: Q1: A 6-kips force is applied to the machine element AB as shown. Knowing that the uniform thickness…

A: given data force = 6 kips. thickness of bar = 0.8 in depth of beam =3 in find the combined at stress…

Q: Knowing that the allowable stress in section ABD is 70 MPa, determine the largest force P that can…

A:

Q: 5. The load P applied to a steel rod is distributed to a timber support by an annular washer. The…

A: Given:stress in steel rod, σst=35 MPaDiameter of rod, dr=22 mmInner diameter of washer, di=25…

Q: A timber beam AB of length L and rectangular cross section carries a single concentrated load P at…

A: From bending moment equation, bending stress is given by:-σb=MyI where,M=bending momenty=distance of…

Q: An annular washer distributes the load P applied to a steel rod to a timber support. The rod's…

A: Given   Diameter of rod, D = 22 mm    Inner diameter, di = 25 mm         Normal stress = 35 MPa Find…

Q: Two wooden members of uniform rectangular cross section of sides a = 100 mm and b = 60 mm are joined…

A:

Q: Knowing that the hole has a diameter of 9 mm, determine (a) the radius rf of the fillets for which…

A:

Q: PROBLEM 1.1 Two solid cylindrical rods AB and BC are welded together at B and loaded as shown.…

A: Given      Length of rod AB = 300 mm = 0.3 m      Length of rod BC = 250 mm = 0.25 m Stress on the…

Q: A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion AB is…

A:

Q: Two L4 x 3 rolled-steel angles are bolted together and used to sup-port the loading shown. Knowing…

A: Draw the free body diagram.

Q: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the…

A: given:

Q: 1. A rod consisting of two cylindrical portions is restrained at both ends. Portion AB has a…

A:

Q: A strain gage located at C on the surface of bone AB indicates that the average normal stress in the…

A:

Q: A14-kN tensile load will be applied to a 50-m length of steel wire with E = 200 GPa. Determine the…

A: Given data:

Q: For the steel truss (E = 29 x 106 psi) and loading shown, determine the deformations members AB, BC,…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.