10.37 PLUS Water (20°C) flows in a 16-cm cast-iron pipe at a rate of 0.1 m/s. For these conditions, determine or estimate the following: a. Reynolds number b. Friction factor f (use Swamee-Jain Eq. (10.39) in §10.6.) c. Shear stress at the wall, To

10.37 PLUS Water (20°C) flows in a 16-cm cast-iron pipe at a rate of 0.1 m/s. For these conditions, determine or estimate the following: a. Reynolds number b. Friction factor f (use Swamee-Jain Eq. (10.39) in §10.6.) c. Shear stress at the wall, To

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter16: Lateral Earth Pressure

Section: Chapter Questions

Problem 16.15P

See similar textbooks

Related questions

Q: Consider the retaming wall shown in the Figure below Calculate the Rankine pasSIve force per unit…

A: Lateral Rankine passive earth pressure is applied at each elevation. Pressure due to Gwt table is…

Q: A vertical masonry chimney has a internal diameter d, and an external diameter d,. The base of the…

A: A chimney is a masonry, clay, or metal architectural ventilation structure that separates hot…

Q: H.W: the velocity profile in pipe is v(r) = v(c)(1 -) Where: v(c)=velocity at center of pipe =2…

A: Calculate the change in velocity with respect to radial distance r, δVδr = Vc-2rR2 Calculate the…

Q: A 3-m 150 mm CHB wall rests on a 600 mm thick concrete footing. The CHB wall weighs 3.3 kN/m² and…

A: Given:- The length of the wall = 3 m The thickness of the concrete footing is 600 mm The weight of…

Q: Determine the stability of the wall in different conditions mentioned down in table and provide a…

Q: P? Air

Q: A 3-m 150 mm CHB wall rests on a 600 mm thick concrete footing. The CHB wall weighs 3.3 kN/m² and…

A: Bearing Capacity of soil: Bearing Capacity of soil is defined because the capacity of soil which…

Q: What will be the nature of surface of pipe if the flow of water is taking place having roughness…

A: Given data: Roughness size, k=0.10 mm Average shear stress at pie boundary, τo=250 Nm2 v=10-6 m2sec

Q: Consider the wall shown below. Dimensions are in meters. sand $' = 30 4 0.5 0.5 Determine the active…

Q: Compute soil pressure, factor of safety for sliding and overturning for the retaining wall shown.…

A: The given values are as follows,The weight of concrete=150pcfThe weight of earth =110pcfThe…

Q: Compute the following: a. wall shear b. wall moment c. Deflection at mid-span

A: As per bartleby guidelines, only 1st question with 3 subparts need to be solved. So, for rest of…

Q: Compute for the combined stress P= 10kN 1.5m 3m 16KN L = 6m P= 10KN 1.5m 16KN b=50mm d=100mm

Q: Determine the magnitude of the hydrostatic force acting per meter length of the wall. Water has a…

A: Consider the following free body diagram: Here, FR is the magnitude of the resultant force.

Q: a. Concrete Pedestal b. Steel Plate c. Stiffener cm) (Thickness=0.5 d. Steel Pipe (Outer dia-10 cm,…

A: Since you have posted a question with multiple sub parts, we will solve first part for you. To get…

Q: Question attached

A: Solution: In soil 1. at depth of z below point A, vertical stress is given byσv=r1z+qpore…

Q: 12kn/m 1okn/m section: 350 A B +50 P: 600KN, e= 200mi CASUme 10%. losses) From the figure shown,…

Q: retain Tor a wate tank supported on ground. Th wall extends above the soil for a few feet. The…

A: The given data is: The soil pressure=45 pcf Hydro-static pressure of salt water=64.1 pcf

Q: PROBLEM 4: CE Brd Exam A 3m diameter x 6m high water tank is made up of 12mm thick steel plate. 4a.…

A: Find pressureP=γwH=9810×6mso

Q: Fe H.W/ The wall exerts a 600 N force on an 80kg person moving at 4 m/s on a circular platform. What…

A: Explained below

Q: Consider the retaming wall shown in the Figure below Calculate the Rankine passive force per unit…

Q: 2. A water gate is 3m high and 1m wide. What is the force acting on the lower stay when the top of…

A: What is the force acting on the lower stay,F?

Q: The wall separates water and glycerin (p=120 kg/m^3). Consider a unit width of the rectangular panel…

A: Given- ρ=120Kg/m3d=6ft The diagram is given below-

Q: Further problems 293 A vertical masonry chimney has a internal diameter d, and an external diameter…

A: The given data is as follows: Internal diameter=diExternal diameter=doHorizontal acceleration=a…

Q: SAND Yay 18KN/m -32 2m Water table SAND Yarated 20KN/m -32 3m Dredge line SAND Yatra 20KN/m -32 Find…

Q: Determine the total active force per meter acting on the wall along with its point of application. q…

A: ka1=1-sin35o1+sin35o=0.271ka2=1-sin195o1+sin195o=0.4995ka3=1-sin0o1+sin0o=1σa1-1=0.271×50=13.55…

Q: Design a 33ft long reinforced concrete shearwall with 15ft height and 8" thickness. Use fc' = 3000…

A: The given data is: Wall length=33 ft=33*0.305=10.65 m Wall height=15 ft=15*0.305=4.575 m Wall…

Q: Geotechnical engineering ( Civil Engineering) X = 6.9 Calculate lateral pressure at 2, 4, and 6m…

A: Given data: Surcharge=10 kn/m2ϕ=30°γ=15 kN/m3It is asked to find lateral pressure at 2, 4 and 6m…

Q: The tank contains water to a depth of 6ft, determine the magnitude and location of the horizontal…

Q: 45° SG = 0.86 | 50 cm A %3D Hinge 10 cm SG = 1.23 80 cm В

Q: What size pipe will maintain a shear stress at the wall of 0.624 psf when water flows through 300 ft…

A: The shearing stress at pipe wall is given by: ζo=(γ×hL2L)×r Where, γ = unit weight of the fluid hL…

Q: Design the load bearing reinforced concrete wall shown if fc = 3000 psi and fy = 60000 psi. For…

A: Given data, fc'=3000psify=60000 psiVu=100kipshw=15 ftLw=8 ft…

Q: The head loss in 50 m long, 12 cm diameter pipe is known to be 6 m when liquid specific gravity is…

Q: f. Minimum width B (in meter) of wall to be safe against sliding if the mobilized friction angle at…

A: Introduction- A wall is a framework and a surface that distinguishes an area, supports a load,…

Q: A 2.75-m- wood-stave pipe has 9 m³/s of water entering through a horizontal 30⁰ reducing bend where…

Q: Y=15 kN/m 4'-28° 4m c'-0 GW.T, Yut 20 kN/m 4-33° 4m The above figure shows a concrete gravity…

A: Area of the earth pressure diagram gives the total active earth pressure acting on the wall .

Q: What size pipe will maintain shear stress at the wall of 0.624 psf when water flows through 300 ft…

A: Given:- The shear stress at the wall of the pipe = 0.624 psf The length of the pipe = 300 ft The…

Q: Determine the total active force per unit acting on the retaining wall along with its point of…

Q: An open cylindrical tank 2m in diameter and 3m high is made from vertical timber planks. It is…

A: Diameter of the cylindrical tank(D)=2 m Height(H)=3 m Allowable stress=83 Mpa

Q: 12 KN Q1 find stress Rod Rod D TCD ТАВ AB CD beam 10 m

Q: Why not active lateral pressure is not consider in basement design

A: Active lateral pressure is not considered for basement design

Q: Solve the pipe network shown in the figure. The 12 in and 16-in are of new cast iron, while the 18…

A: Considering the section with initial assumptions:

Q: Q2. A plain concrete wall, i.e., a wall with no steel reinforcement, rests on a secure foundation…

A: Following is the given information: Height of the wall, h = 3m. Width of the wall, b = 1m. Consider…

Q: A 1.2 m wood stave pipe is laid on a downgrade of 0.90 m per km. The pressure at A in the pipe is 38…

Q: Kindly give me both right solutions with clear calculations. Note: Both questions are subbarts…

A: H= Height of the retaining wall = 4 m. Type of soil = loose sand ⇒ cohesion, C = 0 φ = Angle of…

Q: Investigate the resistance of the wall, whose dimensions and floor properties are given in the…

A: Solution: Given: q = 150 kN/m2 C=0 ∅=30o γconcrete = 24kN/m3 γsoil= 18 kN/m3

Q: Compute the wall stress in a 48-in. steel pipe 1/4 in. thick under a head of 400 ft oil (sp gr 0.82)

A: specific gravity = density of steel pipe containing oildensity of water density of water = 1 gr/cc…

Q: Q1-B/ The wall thickness of a 4-ft-ouside diameter spherical tank is 5/16 in. Calculate theallowable…

Q: Determine the adequacy of a 600-mm-diameter pipe of length 2.5 km with a thickness of 20 mm if it is…

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequalled forces are in…

Q: The 12 in and 16-in are of new cast iron, while the 18 and 24 in are of average concrete. Assume…

A: Consider the below table

Question

10.37 FLUS Water (20°C) flows in a 16-cm cast-iron pipe at a
rate of 0.1 m/s. For these conditions, determine or estimate the
following:
a. Reynolds number
b. Friction factor f (use Swamee-Jain Eq. (10.39) in §10.6.)
c. Shear stress at the wall, To

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Lateral earth pressure distribution against retaining walls

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

An open top standpipe as shown has a radius r= 2.2m and 20 mm wall thickness. Determine the height ? (?? ??????)of the water that will result to a circumferential stress of 24MPa in the wall of the standpipe. NOTE: The specific weightof water is 9.81???3. Remember, pressure is equals to the product of specific weight and height. Use 2 decimal places.
A gate slanted 60 degrees from the horizontal with width = 1.6 m and height = 2.4 m is submerged by a depth of 1.8 m, determine the pressure at the top of the gate in Pa. Use whole number.
5. A 30 cm radius Cast iron main leads from a reservoir whose water surface is at EL. 1590m. In the heart of the city the main, below ground level, is at EL. 1410m. (a) What is the net pressure (b) Assuming static conditions, what is the stress in the pipe wall if the wall thickness is 12.00 mm and the external soil pressure is 250 kPa?6. A continuous wood stave pipe is 2.5 m in diameter and is in service under a head of 30.0 m of water. The staves are secure by means of round 25 mm steel hoops with an allowable stress of 105 MPa. Fine the maximum snarings of the hoops to safely secure the nine.
1. A vertical rectangular gate is 4 ft. wide and 6 ft. high. Its upper edge is horizontal and on the water surface. What is the total pressure on the gate and where is the center of pressure? 2. Solve Problem 1 if the water surfsce is 5 ft. above the top of the gate, other conditions remaining the same. 3. Solve Problem 2 if the plane of the gate makes an angle of 30° with the vertical, other conditions remaining unchanged.
A water tank, 22 ft in diameter, is made from steel plates that are ½ inch thick. Find the maximum height to whichthe tank may be designed if the stress of the wall is limited to 1 ksi. Assume that the pressuredistribution varies linearly.
The head loss in 50 m long, 12 cm diameter pipe is known to be 6 m when liquid specific gravity is 0.9 and viscosity of 0.04N-s/m² at 0.06 m/s. Find the shear stress at the wall of the pipe. a. 31.78 Pa b. 63.2 Pa c. 126.4 Pa d. 15.8 Pa
Refer to Problem 12.3.a. Draw the Rankine passive pressure distribution diagram behind the wall.b. Estimate the Rankine passive force per foot length of the wall and also the location of the resultant.
Refer to Figure 12.13a. Given H = 4 m, α = 0, β = 85º, γ = 17 kN/m3, c' = 0, Φ' = 36º, ẟ'/Φ' = 0.5, and q = 30 kN/m2. Determine the Coulomb’s active force per unit length of the wall.
a. For the vertical wall shown (no GWT, no interface friction), determine and plot the Ko, active, and passive lateral stress distributions acting on the wall b.Suppose the groundwater table in Problem 1 rises to a depth of 4m below the surface (on both sides or the wall) and assume the wall Is under active loading conditions. Assume that soil above the groundwater table Is dry, and that Y sat = 20 kN/m° • Determine and plot the water pressure and at-rest lateral earth pressure acting on the wall. Show the pressure distributions separately (not combined into one distribution). wall.
For the shown wall with smooth vertical face, calculate the total passive earth pressure on the side AB.
A 60 cm CI main pipe leads from a reservoir whose water surface is at Elev. 1590 m. Below the ground surface level, the main pipe is horizontally positioned at Elev. 1410 m. Assuming static condition, what is the stress in the pipewall if the wall thickness is 12.50 mm and the soil pressure is 520 kPa? a.18.2 MPa b.32.6 MPa c.20.5 MPa d.28.7 MPa
A gate slanted 60° from the horizontal with width of 1.6 m and height of 2.4 m is submerged to a certain depth such that the top of the gate is 1.8 m from the water surface. Compute the pressure at the bottom of the gate.