10.4 A load consisting of a 240 resistor in parallel with a (5/18) μF capacitor is connected across the terminals of a sinusoidal voltage source Vg+ where VE = 120 cos 5000r V. a) What is the peak value of the instantaneous power delivered by the source? b) What is the peak value of the instantaneous power absorbed by the source? c) What is the average power delivered to the load? d) What is the reactive power delivered to the load? e) Does the load absorb or generate magnetizing vars? f) What is the power factor of the load? g) What is the reactive factor of the load?

10.4 A load consisting of a 240 resistor in parallel with a (5/18) μF capacitor is connected across the terminals of a sinusoidal voltage source Vg+ where VE = 120 cos 5000r V. a) What is the peak value of the instantaneous power delivered by the source? b) What is the peak value of the instantaneous power absorbed by the source? c) What is the average power delivered to the load? d) What is the reactive power delivered to the load? e) Does the load absorb or generate magnetizing vars? f) What is the power factor of the load? g) What is the reactive factor of the load?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.2MCQ: If the rms phasor of a voltage is given by V=12060 volts, then the corresponding v(t) is given by...

See similar textbooks

Similar questions

A building inventory identified the following equipment with the corresponding impedance or power consumption at 230 V rms. The building power supply is 230 V rms. (Assume that the building voltage supply is the reference phasor) What is the total complex power consumed within the building and the effective power factor? Load 1: 160 - j40  Load 2: 500 VA at 0.85 pf lag Load 3: 450 W at 0.95 pf lead Load 4: 200 + j300 VA
A supply voltage v given by v = (240 sin 314t + 40 sin 942t + 30 sin 1570t) volts is applied to a circuit comprising a resistance of 12 ohmconnected in series with a coil of inductance 9.55 mH. Determine (a) an expression to represent the instantaneous value of the current, (b) the rms voltage, (c) the rms current, (d) the power dissipated, and (e) the overall power factor.
1. A motor load consists of a resistance of 6 Ohms in series with an inductance of 12 mH. Assume 120Vac, 60 Hz supply. a. What is the complex impedance of the load? b. What is the ac current through this load? c. What is theta, the angle between voltage and current through this load? d. What is the power factor? e. What capacitance should be added in parallel with this load to correct the power factor to 1? f. What is the current from the supply when the power factor is corrected?
Understand ac power concepts, their relationships to one another, and how to calculate them in a circuitA load consisting of a 1.35 kΩ resistor in parallel with a 405 mH inductor is connected across the terminals of a sinusoidal voltage source vg, where vg = 90 cos 2500t V. Find 1. a) the average power delivered to the load,2. b) the reactive power for the load,3. c) the apparent power for the load, and4. d) the power factor of the load.
Calculate the active power, reactive power, power factor, Reactive factor if: v=100 cos (wt+150) V and i=4 cos (wt-1050) V Note: Enter the angle in radians. (rad * pi/180) Consider V and I given in the problem represents Vrms and Irms Active Power, P = Vrms Irms cos(θv – θi) Reactive Power, Q = Vrms Irms sin(θv – θi) Power factor (pf) = cos(θv – θi) Reactive factor (rf) = sin(θv – θi)
NEED ASAP please solve this problem,Maximum Average Power Transfer. Please show full and complete solution Note: Answer from the book for Pmax is lower than 50W
A motor draws 680 W at 156 Vrms 60Hz. The motor is operating at a lagging power factor, with a power factor angle of 45 deg.. Determine the capacitance (in microFarad) required to correct the power factor so that the power factor angle becomes 15 deg, lagging. (Give answer in 2 decimal places. Unit is not required)
A transmission line with impedance of 0.085 + j 0.32 Ω is used to deliver power to a load. The load is inductive and the load voltage is 200∠0° Vrms at 60Hz. If the load operates at 20 kVA with a power factor of 0.75 determine the real and quadrature power losses in both the load and the line and the source voltage phasor.
The current through and the voltage across anelectrical component arei(t) = Io cos(ωt + π/4)v(t) = Vo cos ωtwhereIo = 3 mA, Vo = 700 mV , ω = 6.283 rad/sa. Is the component inductive or capacitive?b. Plot the instantaneous power p(t) as a function ofωt over the range 0 < ωt < 2π.c. Determine the average power dissipated as heat inthe component.d. Repeat parts (b) and (c) if the phase angle of thecurrent is changed to 0◦.
A group of small appliances on a 60 Hz system requires 20 kva at 0.85 lagging power factor when operated at 120 Vrms. The impedance of the wire supplying the appliances is (0.01 + j0.08) Ω. The voltage at the load end of the wire is 125 Vrms. Determine: a) the power loss in the wire, b) the capacitor in microfarad needed to improve the power factor to unity.
A load absorbs 72044 W at a lagging power factor of pf = 0.67. If the current flowing through the load is Ix = 0.100 A−rms, determine the impedance of the load.
(P 10.20) Calculate the complex power supplied by the voltage source in the circuit diagram if Vg=40cos10^6t V