10.A. Which of the following is required in each separate service disconnecting means? A. Grounding electrode B. Service conductor C. Main bonding jumper D. Equipment grounding conductor 10.B. When sizing an equipment bonding jumper on the load side of an overcurrent protective device, the size of the conductor jumper is based on the A. current rating of the protective device. B. size of the feeder's equipment grounding conductor. C. size of the grounding electrode conductor. D. size of the conductors feeding the protective device. 10.C. Grounding clamps are typically suitable for connecting how many conductors?

10.A. Which of the following is required in each separate service disconnecting means? A. Grounding electrode B. Service conductor C. Main bonding jumper D. Equipment grounding conductor 10.B. When sizing an equipment bonding jumper on the load side of an overcurrent protective device, the size of the conductor jumper is based on the A. current rating of the protective device. B. size of the feeder's equipment grounding conductor. C. size of the grounding electrode conductor. D. size of the conductors feeding the protective device. 10.C. Grounding clamps are typically suitable for connecting how many conductors?

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.2: Wall-mounted Oven Circuit And Free-standing Range

Problem 12R

See similar textbooks

Similar questions

10.a. Which of the following is a condition of the exception that allows the grounded conductor of feeders tobe used for grounding at separate buildings or structures?A. There are common electrically continuous metallic paths between the feeder source and the destination at the structure served.B. There are common electrically continuous nonmetallic paths between the equipment grounding conductor and the destinationat the structure served.C. An equipment grounding conductor isn't included with the supply circuit to the separate structure.D. Ground-fault protection of equipment is provided on the supply side of the feeder.10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
analyse the rating of wires/ cables and mcb used for different types of loads
1. Which of the following statements about equipment grounding conductors is true?A. Unacceptable equipment grounding conductors include conduit, tubing, and cable armor.B. They must be capable of withstanding the higher level of ground-fault current to perform their safety function.C. They increase voltages above ground potential on conductors and equipment enclosures during normal operation.D. When they're far from their associated circuit conductors, impedance values are kept as low as possible during ground-faultconditions.
What are the steps for plotting points on microstation uisng offset, station, side and elevation?
A cable TV company was interested in making its operation more efficient by cutting down on the distance between service calls while still maintaining at least the same level of service quality. A treatment group of 18 repairpersons was assigned to a dispatcher who monitored all the incoming requests for cable repairs and then provided a service strategy for that day’s work orders. A control group of 18 repairpersons was to perform their work in a normal fashion—that is, by providing service in roughly a sequential order as requests for repairs were received. The average daily mileages for the 36 repairpersons are recorded in the table below. a. What are the populations of interest in this study?b. What is the level of significance of your test?c. Is there significant evidence that the treatment group had a smaller average daily mileage than the control group? Use α = 0.05
Which of the following is a term missing from the National Electrical Code but used by manufacturers of equipment that's suitable for use as service equipment? Micro-grid  Selective coordination Neutral disconnect link Grounding triad The _______ is required to be connected to the grounded conductor of the sensitive electronic system on the line side of the separately derived system disconnecting means. main bonding jumper  equipment grounding terminal bus neutral ground strap neutral disconnect link
List the methods by which an equipment grounding conductor is connected to a device box.
A Type NM cable carries a branch circuit to the outside of a building, where it terminates in a metal weatherproof junction box. From this box, a short length of EMT is installed upward to another metal weatherproof junction box on which is attached a cluster of outdoor floodlights. The first box is located approximately 24 in. (600 mm) above the ground. To Meet Code, do the metal boxes and metal raceway have to be grounded? Yes _______________ No _______________ NEC _______________.
4. What can installation records be used to determine while servicing equipment?A. Broken connectors in a cable linkB. Problems due to aging during operationC. Broken fiberD. Decreased bending radius during operation
2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service head, andany fittings necessary for the termination and support of overhead service conductors?A. Drip loopB. Service lateralC. Service dropD. Service mast 2.b. What's likely to happen when connected parallel conductors are different lengths?A. An NEC violationB. Misidentification of conductor cablesC. An uneven distribution of currentD. Conductor termination
10.b. A service disconnection means must be installed adjacent to, within sight of, and no more than_______ feet from a mobile home.A. 20B. 30C. 10D. 50
What is the minimum-size supply-side bonding jumper required if installed on the line side of a 300-ampere service disconnecting means if the service conductors are sized at 400-kcmil copper? a) 3 AWG copper b) 2 AWG copper c) 1/0 AWG copper d) Parallel 2 AWG copper conductors