1008. A timber beam 150 mm wide by 250 mm deep is to be reinforced at the top and bottom by steel plates 10 mm thick. How wide should the steel plates be if the beam is to resist a moment of 50 kN-m? Assume that n = 15 and the allowable stresses in the wood and steel are 8 MPa and 110 MPa, respectively. Ans. b = 143 mm doen is to be 1009

1008. A timber beam 150 mm wide by 250 mm deep is to be reinforced at the top and bottom by steel plates 10 mm thick. How wide should the steel plates be if the beam is to resist a moment of 50 kN-m? Assume that n = 15 and the allowable stresses in the wood and steel are 8 MPa and 110 MPa, respectively. Ans. b = 143 mm doen is to be 1009

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the required amount of reinforcement (in in2) considering the ultimate moment below. Use english units. Note: Use the following equations for minimum reinforcement in English units. Pmin for flexure = (3*sqrt (f'c))/fy greater than or equal to 200/fy f'c = 3000 psi fy = 40 ksi Mult = 200 ft-k
The main beam of UB 610 x 229 x 101 kg/m in steel grade S275 supportssecondary beamsof UB 406 x 140 x 39 kg/mon its top flange.The schematic diagram of the floor supported by the beams is presented in Figure 1. b)The slab floor is reinforced concrete 150 mm thickwith 50 mm screed on top of it. The slab floor carriesthe uniform distributed load of 400 kg/m2.Calculate the ULS load on the secondary beam. 4xxx= 4715 1xxx= 1715 50xx= 5015
4. The rectangular piece of wood ,50mm by 100mm is used as a compression block. The grain of the wood makes a 20 degrees angle with the horizontal , as shown in the figure . Determine the largest axial force P that can be applied safely if the allowable stresses on the plane of the grain are 18MPa for compression and 4MPa for shear.
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: Using a T-beam geometry, determine the required amount of flexure bars for maximum ultimate bending. = [As] sq.mm (whole number)
The wooden section of the beam is reinforced with two steel plates as shown. Determine the maximum moment M that the beam can support if the allowable stresses for the wood and steel are (sallow)w = 6 MPa, and (sallow)st = 150 MPa, respectively. Take Ew = 10 GPa and Est = 200 GPa.
Compute the bending stresses in the beam shown, f'c = 28 MPa Es=200000MPa M=165 kN-m
A beam has a uniform dead load and live load has a fixed support at both ends. If the beam properties are given below, what is the stress at bottom of the beam section at the midspan. (MPa) Properties: Beam width = 270 mmBeam height = 375 mmWLL = 14.38 kN/mWDL = 18.41 kN/mSpan of the beam = 8 mPrestressing force = 481 kNeccentricity = 103 mm
Two wooden joists 100mm * 200 mm along the joint AB as shown in figure. Determine the normal and shearing stress in glued surface if P = 400 N
ASAP PLEASE. 4 DECIMALS What is the value of R1 in kN? What is the value of R2 in kN? Locate the point of zero shear from point A in meters.
Determine the bending stress (in Pa) at the top of the beam at point C for the beam shown belowif P = 1639 N, T = 4678 Nm, a = 0.75 m, b = 1.07 m, c = 0.94 m, w = 44 mm, and h = 75 mm . Round off the final answer to one decimal place.
What is the force carried by member DE? Select one: a. 402 kN b. 240 kN c. 204 kN d. 420 kN
•Timber beamSafe working stress = 25 MPaCross-section dimensions:height = 119 mm,width = 66 mmProving ring number 293. Steel beam Safe working stress = 200 MPa Cross-section dimensions:external height = 149 mm,external width = 50 mm,wall thickness = 3.0 mm,Proving ring number 1522.1)Calculate safe max bending moment in the central part of the beam using Mmax = (I)(max stress)/(D/2)2) calculate Safe applied force in the proving ring or tie rod, assuming a symmetrical setup as in the photowith a ‘lever arm’ of 600 mm