10N 1m 1 m 1 m 1m c 1 m 5N 1m E 10N + 10N 1m 1 m 20N 5N 10N Find the summation of torque / moments at point B. Find the summation of torque / moments at point C. Find the summation of torque / moments at point D. Find the summation of torque / moments at point E. Find the summation of torque / moments at point A.

10N 1m 1 m 1 m 1m c 1 m 5N 1m E 10N + 10N 1m 1 m 20N 5N 10N Find the summation of torque / moments at point B. Find the summation of torque / moments at point C. Find the summation of torque / moments at point D. Find the summation of torque / moments at point E. Find the summation of torque / moments at point A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine the coordinate direction angles of theforce F1 and indicate them on the figure.
A solid constant-diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the internal torque in segment (2) of the shaft. Assume that TA = 135 N-m, Tg = 318 N-m, Tc= 361 N-m, and To = 178 N-m.
An experimental device imparts a force of magni tude F = 225 N to the front edge of the rim at A to simulate the effect of a slam dunk. Determine the moments of the force F about point 0 and about point B. Finally, locate, from the base at 0, a point C on the ground where the force imparts zero moment.
Replace the force system acting on the frame by an equivalent resultant force and a couple of moment acting at point A. Suppose that F1 = 300 N and F2 = 100 N Determine the magnitude of the resultant force. Determine the angle between the resultant force and the x axis. Determine the equivalent resultant couple moment about point A.
The center of gravity 'G' of a 20-ton mobile crane is as shown, It can carry a load 'L'of 24 tons without tipping to the right with the use of a counterweight 'C'. Determine the value of C (in tons) and its position 'a' (in feet) so that the crane will remain in equilibrium both when the maximum load L is applied and when the load L is removed. (d=1, b=6, c-12] (give your answer for 'C in here, and for the distance 'a in Problem 4b)
Determine the moment (N m) caused by F1 about point A.Determine the moment (N m) caused by F2 about point A.Determine the moment (N m) caused by F3 about point A.
In the gear system shown in the figure, the motor applies a torque of 231 N-m to the gear at A. A torque of TC = 440 N-m is removed from the shaft at gear C, and the remaining torque is removed at gear D. Segments (1) and (2) are solid 38-mm-diameter steel (G = 80 GPa) shafts, and the bearings shown allow free rotation of the shaft. Assume DA = 110 mm, DB = 370 mm, L1 = 1.7 m, and L2 = 1.1 m. Calculate the rotation angle of gear D relative to gear B.
Calculate the value of the deflection at point B due to concentrated load P in the form Enter the numerator in the answer box below in kNm3 to three decimal places. Assume the positive direction of deflection in the positive direction of v axis.
• b1 = 300 mm • b2 = 180 mm . d1 = 250 mm • d2 = 350 mm • f'c = 28 MPa •fy=414 MPa • eccentricity = 500 mm Determine the nominal axial load in kN if it is applied at an eccentricity of 200 mm.
The 42 foot long overhanging beam shown is supported by a pin at A and a roller at C. The beam supports a point load of 42 kips at point B. Determine the slope at pin A, deflection at point B, and the slope and deflection at point D. Modulus of Elasticity, E = 10,000ksi, Moment of Inertia, I = 2500in4. Let slope and deflection be functions of x, with x positive to the right.
Determine the magnitude of the moment of the force about the y-axis. Note that F = 10i +30j + 5k.
The A-frame is being hoisted into an upright position by the vertical force of F = 80 lb. Determine the moment of this force about the x axis when the frame is in the position shown.