11- What is the current through the motor winding of Fig. 12-54 when the gate voltage is low?When it is high?12- The motor winding of Fig. 12-54 is replaced by another with a resistance of 6 V. What isthe current through the winding when the gate voltage is high?VDD+12 VFlgure 12-54м) 10 2+10 VMTP4N80E

Since you have posted multiple different question. we will solve the first question for you. To get…

Answered: 11- What is the current through the…

Engineering

Electrical Engineering

11- What is the current through the motor winding of Fig. 12-54 when the gate voltage is low? When it is high?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

12. i) Consider a PV Module with 12 solar PV cells with the Size of each 15cm x 10cm are connected in series. Choose the correct statement for the above. (Assume necessary data) a. The output voltage is 6 V, the output power is 275W b. The output voltage is 6 V, the output power is 0.275W c. The output voltage is 6 V, the output power is 27.5W d. The output voltage is 24 V, the output power is 2.25W 12. ii) For the above given same PV Module, Choose the correct statement. (Assume necessary data) a. The output power is 2.75W and the output current is 0.458A b. The output power is 27.5W and the output current is 4.58A c. The output power is 54W and the output current is 4.5A d. The output power is 275W and the output current is 45A
Izl min=lmA ZDi Vzl=3.1V Iz2 min.=1.5mA The maximum power of each of the three zener diodes in the branch shown is ZD2 Vz2=6.2V Iz3 min.=2mA ZD3 Vz3=2.7V 500 mW. The maximum current of the branch should not be more than : O a. 256.8 mA O b. 161.3 mA O c. 80.6 mA O d. 241.9 mA O e. 185.2 mA O f. 265.8 mA g. 427.1 mA O h. 346.5 mA
A platinum resistance coil is to be used as a temperature sensor and has an initial resistance of 200 ohms .It forms one arm of a Wheatstone bridge with the bridge being balanced at this temperature and each of the other arms also being 200.If the temperature coefficient of resistance of platinum is 0.0045 , what will be the output voltage from the bridge for every 5 degree changes in temperature if the supply voltage is 15.0 V? a.0.16V b.0.159V c.0.16875 V d.0.17V
Question 3 Find 1₁, 12, 13, and Vo in the following circuit. Use diode constant voltage drop (CVD) model with VDO = 0.5 V. You must show your work in details and you must verify your assumptions. The circuit parameters are:, V₁ = 10 V, V₂ = 5 V, V3 = 1, R₁ = 30 KS2, R₂ = 100K. V₁ V₂ KH I₁ D₂ 1₂ 13 Vo R₁ kN m • R2 ΚΩ V3
use the constant voltage drop model in analyzing the diode circuit below: 10 92 V₁ (+ M 1 V D₁ If V₁ is -3 V, what would be the state of the diodes? A. D₁ and D₂ are both OFF C B. D₁ is OFF and D₂ is ON - 1 V D₂ C. D₁ is ON and D₂ is OFF D. D₁ and D₂ are both ON + 1092 Vo
A platinum resistance coil is to be used as a temperature sensor and has a resistance at 0°C of 100 . It forms one arm of a Wheatstone bridge with the bridge being balanced at this temperature and each of the other arms also being 100 . If the temperature coefficient of resistance of platinum is 0.0039 K , what will be the output voltage from the 1 bridge per degree change in temperature if the supply voltage is 6.0 V?
G2/0.Desgn Circint as the fallowing peseriptom: A- the positive Cycle of the vout signal is 3.2 and Negatne cycle is 4-3 (Note: we must used preetical Diodes and vin is tov) B- the positive cycles of vout is 5:3 and Negative cycle is (5. 4) [note:consider tovavd we must used Capaetor with praetical Diade) Vin =
32 Basic Zener Regulation Past If the input voltage, Vi = 40 V, the zener diode voltage Vz = 15 V, R = 1002, load resistance is 802, and Pzm = 1 W. The following statements are true except, * load voltage is exactly the same as Vz load voltage is greater than Vz Power delivered by the input voltage is 10 Watts power dissipation of R = 6.25 Watts IN+ R₂
7:-V O Voltage_Doubler_. > Vin = 5 Vpk RI = 4KQ C1-10μF C1 = 10µF Second Year Electronics Laboratory Discussion: 1. Compare the characteristies of voltage doubler with an ordinary a.c to d.c rectifier 2. Discuss the possibit ty of using the voltage doubler circuit as a regulated power su ly. 3. Suggest u circuit d.agram for a voltage tripller and compare it with the voltage doubler circuit. Table (1) Rr. (KO) V. (V) Vip-p (V) Va (V) V.R 10 4. النقطة الثانية في المناقشة غير مطلوبة II
When resistors with higher wattage ratings are required, resistors are generally used to dissipate the excessive heat. a) Variable b) Fixed c) Wirewound d) Preset The diode is considered shorted when both anode and cathode has a) Low resistance b) High resistance c) Different resistance d) None of the above When two resistors are connected in parallel then their overall power rating is a) Increased b) Decreased c) Doubled d) Reduced
Using complete diode model and assuming that the forwyd resistance of thediode is 152 and a Germanium diode, the voltage across the resistance R equals to R. 5k0 12V 11.65 V 11.7 V 12 V None of the above Moving to another question will save this response. MacBook Pro
Instructions Calculate the DC voltages and currents in the circuit. Find for the current emitter, collector current and collector voltage. +12v 5kN 5kN Von Voz Q2 Vi2 2.7kN