12-2 (a) Determine the ms nolse vollage produced by a 120-kS2 resistance in an 80-KHz bandwidih al the standard temperature To = 290 K. (b) Delermine the rms noise vollage if the resistance is changed to 1.2 MS2. (C) Determine the ms noise vollage ir the resistance is changed to 12 M2. (d) wilh R = 12 MS2, delermine the rms noise vollage ir the bandwidth is changed to 800 kHz. (e) With R = 12 M2, determine the rms noise vollage ir the bandwidih is changed to 8 MHz. () With the values of Rand B of part (C), delermine the rms noise vollage if the temperalure is decreased to 270 K.

12-2 (a) Determine the ms nolse vollage produced by a 120-kS2 resistance in an 80-KHz bandwidih al the standard temperature To = 290 K. (b) Delermine the rms noise vollage if the resistance is changed to 1.2 MS2. (C) Determine the ms noise vollage ir the resistance is changed to 12 M2. (d) wilh R = 12 MS2, delermine the rms noise vollage ir the bandwidth is changed to 800 kHz. (e) With R = 12 M2, determine the rms noise vollage ir the bandwidih is changed to 8 MHz. () With the values of Rand B of part (C), delermine the rms noise vollage if the temperalure is decreased to 270 K.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.18P: Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of...

See similar textbooks

Similar questions

The maximum values of the alternating voltage and current are 400 V and20 A respectively in a circuit connected to 50 Hz supply and these quantitiesare sinusoidal. The instantaneous values of the voltage and current are 283V and 10 A respectively at t = 0, both increasing positively. Write down theexpression for voltage and current at time t and determine its phasedifference and indicate which quality leads or lags the other.
A non-sinusoidal quasi-square wave voltage v(t) is applied to a nonlinear load, resulting in a non-sinusoidal current i(t). The voltage and current waveforms are shown below. Assume any values of your choice for Vp (≤ 200 V) and Ip (≥ 5 A). 1. calculate the average power and net power factor of the load. 2. The total load harmonic distrotion (THD) of the load current, assuming the smallest frquency term as fundamental.
Please solve Last time Not give details solution. Give good ans i give upvote. A 3-phase alternator has the line voltage of 11 kV. The generator is connected to a circuit breaker. The inductive reactance upto the circuit breaker is 50/phase. The distributed capacitance upto circuit breaker between phase and neutral is 0.001 µF Determine peak restriking voltage across the CB, frequency of restriking voltage transients average rate of restriking voltage upto peak restriking voltage, maximum RRRV.
3. Perform the following steps for the given circuit in below.c) Find the Av, if the Vs = 100mV_rms, IDSS = 12mA, VP = -4V, VDD = +12V, RD =3.6kΩ, RS = 1.1kΩ.d) Find the Vo, if a load resistance of 10kΩ is connected to the output of the circuit.Vs = 50mV_peak, IDSS = 12mA, VP = -4V, VDD = +12V, RD = 3.6kΩ, RS = 1.1kΩ.
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
FROM THE SOLVE DIAGRAM FOR A COMBINATIONAL ELEMENT ACCORDING TO THE NOMENCLATURE FOR IT, WITH SAT DATA VCC= 18V, VBE= .47V, VBB = 9V, VCE= .92 V ICSATMAX= 290mA. β= 55 RE= 3.3 OHMS WHAT TOLERANCES DOES THE USE OF CORRESPONDING STANDARDIZED VALUES FOR RC YIELD?
How much is the Zt for a 20-Ω resistor in series with a 20-Ω capacitive reactance? If a 20 V is across the R and also 20 V is across Xc, what is the supply voltage and phase angle of the circuit?
Is it possible to measure the phase-shift angle in an AC single-phase circuit by an indirect method using an ammeter and a voltmeter? - Yes, but an instrument must be added to measure the active resistance of the load. - Yes, but an instrument must be added to measure the active power dissipated by the load. - Yes, but an instrument must be added to measure the frequency.
. At a 12.47 kV (line to line) distribution system the communication interference (CI) was observed due to 5% of 5th harmonic currents generated by a 3000 kVA arc furnace. In order to avoid CI it is required to convert an existing 600 kVAr capacitor to 5th harmonic filter considering the total kVAr should not exceed 135%. Calculate the following: (i) Capacitor reactance (ii) Reactance of the series reactor (iii) Fundamental frequency current (iv) 5th harmonic frequency current (v) Tuned frequency voltage (vi) Total rms current (vii) Fundamental frequency voltage (viii) Voltage (rms) across the capacitor bank (ix) Check whether the filter kVAr rating is within limit? (x) Comment how the existing capacitor bank is converted to filter
chapter 1 Q1 The rms value the AC input voltage to the of Circuit shown is 230U, and the firing angle is maintained Current is 5 A. constant at 45° so that the load a) Calculate the de output voltage. b) Assume that the load resistance remains the a same, find the current is a FWD is used at the output. c) If^ prime prime ScR^ prime prime " is open circuited, find load voltage and current a is the Same) (FWD is still connected and high. "L Load Ans[146.4U,6.03A ; 3.c2A] 3 3 FWD
Let a series RLC network be connected to a source voltage V, drawing a current I. (a) In terms of the load impedance Z=ZZ, find expressions for P and Q, from complex power considerations. (b) Express p(t) in terms of P and Q, by choosing i(t)=2Icost. (c) For the case of Z=R+jL+1/jC, interpret the result of part (b) in terms of P,QL, and Qc. In particular, if 2LC=1, when the inductive and capacitive reactances cancel, comment on what happens.
In the case of reactive power compensation in a low voltage distribution network and increasing the power factor to cosQ2 = 0.92 as a result of compensation while cosQ1 = 0.75, which of the following expresses the change in apparent power transmitted from the line a) increase by 22.66% b) decrease by 22.66% c) increase by 18.47% d) increase by 15.00% e) decrease by 18.47%